1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Paint Sprayer
  5. 86
  6. Set up and operating instructions manual

Central Pneumatic 86 Set Up And Operating Instructions Manual

Touch-up gun
Hide thumbs
Table of Contents

Advertisement

Quick Links

TOUCH-UP GUN
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
Copyright
1997 by Harbor Freight Tools
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Model
3491 Mission Oaks Blvd., Camarillo, CA 93011
00086
®
. All rights reserved. No portion of this
®
.

Advertisement

Table of Contents
loading

Related Manuals for Central Pneumatic 86

Summary of Contents for Central Pneumatic 86

  • Page 1 Copyright 1997 by Harbor Freight Tools manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353. Model 00086 ®...

  • Page 2: Specifications

    USE EYE PROTECTION. Coatings will cause eye irritation. Wear ANSI approved chemical splash safety goggles. Goggles are available from Harbor Freight Tools. When cleaning, be especially careful as solvents can be forcibly ejected from fluid and air passages.
  • Page 3 BE AWARE OF OTHER PEOPLE. Never spray directly at people or animals. The Touch-Up Gun needs minor assembly. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Item #...
  • Page 4 ASSEMBLY Connect the Spray Unit to the Canister Unit as shown in Figure 1. BEFORE YOU USE YOUR TOUCH-UP GUN A coupler is required to connect the Touch-Up Gun to an air compressor. Select the coupler, e.g. ¼” “M” style NPT, etc. that mates with the end of the air hose you are using, and screw it onto the AIR CONNECTION (#23) located at the end of the Touch-Up Gun’s handle (see Figure 2).

  • Page 5: Operation

    Setup Refer to Figure 3 for the location of parts called out in this section. Step 1. Move the LEVER (#29) counterclockwise until the YOKE (#30) is free from the CUP LOCKS (#35). Step 2. Lift and remove the Paint Gun from the CUP (#34). Step 3.
  • Page 6 The fan size is adjusted by turning the FAN ADJUSTING SCREW (#28) clockwise for a narrow spray and counterclockwise for a wider spray. Adjusting Jet Shape The Jet Shape is adjusted by turning the AIR CAP (#1). It should be perpendicular to the ground to create a horizontal jet and parallel to the ground to create a vertical jet.

  • Page 7: Spraying Techniques

    Your Touch-Up Gun is designed for light touch-up work, stenciling, and small job duties. For heavy or medium production work, we suggest our H.V.L.P. and professional model spray guns. For most uses, e.g. painting walls, benches, vehicles, etc., the best results are obtained by spraying thin, even coats of paint.

  • Page 8: General Maintenance

    General Maintenance Checking & Replacing the Needle Needle wear is expexcted and inspection during Cleaning will ensure the continued top- performance of your Touch-Up Gun. If needle tip wear is noted: Step 1. Unscrew the FAN ADJUSTING SCREW (#28) and remove the SPRING (#27).
  • Page 9 Cleaning: WARNING: Always dispose of paints, coating and other chemicals in a proper way. If you have questions regarding the proper disposal of any chemical, contact the chemical manufacturer for Step 1. Depressurize the cup and disconnect the air hose. Step 2.
  • Page 10 Lubrication: Before and after each use of the TOUCH-UP GUN, perform the following lubrication process, using a non-silicon, spray gun lubricant: Step 1. Put two or three drops of lubricant on the NEEDLE (#24), in front of the TRIGGER (#14). Tip the gun backward and allow the lubricant to drip into the front of the GUN HOUSING (#13).

  • Page 11: Preventative Maintenance

    Periodically check the following: Needle Wear: Visually inspect NEEDLE (#24) tip for wear. NEEDLE wear will cause the paint pattern to be uneven. If NEEDLE wear is noted, replace the NEEDLE per GENERAL MAINTENANCE, CHECKING AND REPLACING THE NEEDLE. Cup Gasket Wear: Step 1.

  • Page 12: Parts List

    PART # DESCRIPTION Air Cap Inner Ring Retainer Ring Fluid Nozzle Ring Packing Vol. Adj. Screw Receiver Volume Adjusting Screw Gun Housing Trigger Trigger Screw Packing Packing Valve Nut Stem Assembly Spring SKU 00086 For technical questions, please call 1-800-444-3353. PARTS LIST PART # DESCRIPTION...
  • Page 13 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents