Central Pneumatic 60314 Owner's Manual & Safety Instructions

Central Pneumatic 60314 Owner's Manual & Safety Instructions

1-1/2 gallon texture spray gun

Advertisement

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 60314 and is the answer not in the manual?

Questions and answers

Summary of Contents for Central Pneumatic 60314

  • Page 2: Table Of Contents

    Distractions are able to result in fire, and injury to persons. the loss of control of the tool. Page 2 For technical questions, please call 1-800-444-3353. Item 60314...
  • Page 3: Personal Safety

    Use only lubricants supplied with the by qualified repair personnel. tool or specified by the manufacturer. b. When servicing a tool, use only identical replacement parts. Use only authorized parts. Item 60314 For technical questions, please call 1-800-444-3353. Page 3...
  • Page 4: Air Source

    Cubic Feet per Minute flow SCFM at standard conditions WARNING marking concerning Risk of Respiratory Injury. Wear NIOSH-approved respirator. National pipe thread, tapered WARNING marking concerning Risk of Explosion. Page 4 For technical questions, please call 1-800-444-3353. Item 60314...
  • Page 5: Specifications

    (California Health & Safety Code § 25249.5, et seq.) Specifications Maximum Air Pressure 90 PSI Hopper Capacity 1.5 gal. Air Inlet 1/4" - 18 NPS Air Consumption 8 CFM @ 90 PSI Item 60314 For technical questions, please call 1-800-444-3353. Page 5...
  • Page 6: Setup

    5. Turn on the air compressor according to and quick coupler, will make operation the manufacturer’s directions and allow more efficient, but are not required. it to build up pressure until it cycles off. Page 6 For technical questions, please call 1-800-444-3353. Item 60314...
  • Page 7 7. Inspect the air connections for leaks. measure to attempt to discharge the tool in a Repair any leaks found. safe fashion after disconnecting to ensure that the tool is disconnected and unpowered. Item 60314 For technical questions, please call 1-800-444-3353. Page 7...
  • Page 8 NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Page 8 For technical questions, please call 1-800-444-3353. Item 60314...
  • Page 9: Components And Controls

    Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Components and Controls Hopper Fluid Clamp Control Knob Lock Nozzle Trigger Inlet Trigger Lock Figure C Item 60314 For technical questions, please call 1-800-444-3353. Page 9...
  • Page 10: Operation

    Therefore, do the job. Remove the Lock Ring to not fill the Hopper completely until the change the Nozzle, then replace proper consistency is achieved. and tighten the Lock Ring. Page 10 For technical questions, please call 1-800-444-3353. Item 60314...
  • Page 11: Spraying Technique

    Hopper and Gun Body with solvent. 7. Clean Spray Gun thoroughly immediately after EVERY use, according to instructions on the following pages. Item 60314 For technical questions, please call 1-800-444-3353. Page 11...
  • Page 12: Maintenance

    6. Inspect fluid needle and make sure sources in a vapor free area. it is not bent. If it is bent, have it e. Keep class ABC fire replaced by a qualified technician. extinguisher nearby. Page 12 For technical questions, please call 1-800-444-3353. Item 60314...
  • Page 13 4. Worn/damaged air valve/seat. 4. Replace air valve. 5. Bent valve stem. 5. Replace valve stem. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service. Item 60314 For technical questions, please call 1-800-444-3353. Page 13...
  • Page 14: Parts List And Diagram

    Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 14 For technical questions, please call 1-800-444-3353. Item 60314...
  • Page 15: Assembly Diagram

    NOTICE Clean the Spray Gun IMMEDIATELY after use. Delayed or inadequate cleaning will permanently clog the Spray Gun. Assembly Diagram Item 60314 For technical questions, please call 1-800-444-3353. Page 15...
  • Page 16: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.

Table of Contents