Harbor freight tools central pneumatic series 2 in 1 flooring cleat staple nailer model 94446 assembly and operating instructions contractor series (12 pages)
Page 1
2008 by Harbor Freight Tools herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must be used for the applicable SKU 98733 For technical questions, please call 1-800-444-3353. conditions. Wear heavy-duty work gloves during use. Wear a full face shield if you are producing metal fil- ings or wood chips.
Store the tool when it is idle out of reach of children and other un- SKU 98733 For technical questions, please call 1-800-444-3353. trained persons. A tool is dangerous in the hands of untrained users.
Cubic Feet per Minute flow at SCFM standard conditions National pipe thread, tapered National pipe thread, straight Chart continued in next column. SKU 98733 For technical questions, please call 1-800-444-3353. Symbol Definitions Symbol Property or statement WARNING marking concerning Risk of Eye Injury.
Page 6
This tool vibrates during use. Re- peated or long-term exposure to vibra- tion may cause temporary or permanent physical injury, particularly to the hands, SKU 98733 For technical questions, please call 1-800-444-3353. arms and shoulders. To reduce the risk of vibration-related injury:...
Tools at the number shown throughout the manual as soon as possible. • This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up. SKU 98733 For technical questions, please call 1-800-444-3353. Air Supply TO PREVENT EXPLOSION:...
Page 8
If the tool will not be used at this time, turn off and detach the air supply and safely discharge any residual air pressure. SKU 98733 For technical questions, please call 1-800-444-3353. Note: Residual air pressure should not be present after the tool is disconnected from the air supply.
WARNING! Even though the Nailer should be empty during this proce- dure, ALWAYS point the Nailer at a piece of scrap wood when testing. Completely empty Magazine (71). SKU 98733 For technical questions, please call 1-800-444-3353. Trigger (56) Magazine (71) Safety (37)
Slide the strip of 60 10-Gauge nails forward in Magazine. Unlatch the Feeder Shoe (69) and allow Feeder Shoe to slide forward against strip of nails. SKU 98733 For technical questions, please call 1-800-444-3353. Operating Framing Nailer Adjust the Exhaust Cover (4) to direct as desired.
Reload the magazine with a new nail strip. SKU 98733 For technical questions, please call 1-800-444-3353. Pull back on the Feeder Shoe and with your other hand, pull the tab down on the Lock (75) and guide the Feeder Shoe back into position.
Cleaning, Maintenance, and Lubrication Note: Anytime inspection, maintenance and cleaning are done: SKU 98733 For technical questions, please call 1-800-444-3353. Disconnect the Framing Nailer from its air supply. Empty Magazine (71) completely. Try to fire the Nailer into a piece of...
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 98733 For technical questions, please call 1-800-444-3353. Troubleshooting Likely Solutions 1.
Piston Cylinder O-Ring (M67 x 3) O-Ring (M60.25 x 2.5) Restrictive Seal O-Ring (M97.5 x 3.5) Bumper A Bumper B Body SKU 98733 For technical questions, please call 1-800-444-3353. PARTS LIST Part Description O-Ring (M62.3 x1.8) Nose Spring Washer Screw...
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. REV 09g SKU 98733 For technical questions, please call 1-800-444-3353. Page 15...
Page 16
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.