Table of Contents
Advertisement
Parts List
Item #
Part #
Quantity
Description
1
SS-94-0006
1
Dial
2
05-94-0099
1
Dial Mount
3
05-94-0068
1
Rate Gate
4
05-24-1101
1
Rate Gate Linkage
5
05-90-0044
1
Cable Fastener
6
05-94-0097
2
Double Track Rate Gate Guides
7
05-94-0045
1
Accuway™ Adjustment Screw
8
05-94-0048
1
Accuway™ Adjustment Nut
9
05-94-0043
1
Accuway™
10
SS-94-0010
1
Bevel Gear (nylon)
11
SS-96-0003
1
Agitator Wire
12
SS-94-0012-1
1
Spinner
13
05-46-0019
1
Spinner Shaft
14
SS-90-0002
2
Roll Pin / Bevel Gear / Spinner
15
SS-90-0001
2
Roll Pin / Bevel Gear / Pinion Gear
16
SS-90-0002
2
Felt Washer / Above Gearbox & Below Agitator
17
SS-94-0009
1
Pinion Gear (nylon)
18
SS-94-0007
1
Hopper Bottom Bushing
19
05-46-2210
1
Axle
20
05-90-0065
1
Clevis Pin / Drive Wheel
21
05-90-0089
1
Hair Pin / Drive Wheel
22
05-94-0008
2
Gear Box Cover Halves (two)
23
SS-94-0014
4
Gear Box Clamp Rings
24
05-94-0053
2
Axle Bushings
25
05-24-1030
1
Frame
26
99-50-1081
1
Cotter Pin / Idle Wheel
27
05-24-1040
2
Handle "Braces"
28
05-24-1120
1
Ground Prop
29
SL-HP-1015
1
Handle "Center Section"
30
05-24-1010
1
T - Handle
31
SS-94-0013
2
Handle Grips
32
05-98-0048-1
1
On / Off Control Lever
33
05-90-0042
2
10 - 24 x 1 3/16" Bolt / Control Levers
34
05-91-0008
2
10 - 24 Lock Nut / Nylon Insert / Control Levers
35
05-90-0054
10
1/4" - 20 x 1 1/2" Hex Bolt / Ground Prop to Frame
36
SS-91-0004
10
1/4" - 20 Lock Nut / Nylon Insert
37
05-95-0046
2
Idle & Drive Wheel / 10"
38
05-24-1105
1
Cable Clamp
39
05-46-0500
1
Hopper
40
05-99-0089
1
Manual
41
05-94-0029
1
Spinner Shaft Bushing - Spacer / Gear Box
42
99-10-0227
1
Washers / Idle Wheel
43
05-94-0064
3
Nylon Washer / Hopper
44
05-92-0007
2
Washer / Drive Pin
45
05-96-0046
1
Screen
7
Read Before Using
SPEED - ACCURACY - FREEDOM FROM STRIPES AND STREAKS
are yours - when you use this Spreader.
The spread width ranges from 6 ft. to 12 ft. wide, depending on the
volume/density, particle size of the material and the rate of travel.
The spread thins or feathers at the outer edges, eliminating sharp,
"Edge of spread" lines which cause stripes and streaks. Extra coverage
can be given under trees and other heavy feeding areas without show-
ing "edge of spread" lines.
Gaps and double overlaps are less likely. Small errors in travel are for-
given and do not show.
WARNING: When spreading products containing herbicides, exercise extreme
caution with respect to careless spreading and to wind-drift.
CONTACT OF SOME PRODUCTS ON SOME PLANTS CAN BE FATAL.
If a dial setting is not found, use the size and weight comparison table
found on page 12.
Determine a dial setting on the low side. If the setting proves to be
too low, cover the area more than one time. A higher setting can be
used when a proven dial setting is established.
REMEMBER - Published dial settings can be approximate only. The
operation of the spreader, the condition of the material (damp or dry
or over-pulverized) and weather conditions, are all contributing factors.
For these reasons, it's often a good idea to spread the area 2 times -
at one-half rate - in cross directions (SEE INFORMATION ON ONE-HALF
RATE DIAL SETTINGS ON REFERENCE CHART ON THE BACK PAGE.
SPREADING AT ONE-HALF RATE DIAL SETTINGS IS HIGHLY RECOM-
MENDED UNDER DAMP & HUMID CONDITIONS.
BECOME FAMILIAR WITH THE OPERATION OF THE SPREADER
BEFORE YOU PUT MATERIAL IN THE HOPPER.
Practice walking with the spreader, opening and closing the rate gate
at the appropriate times.
Travel at a constant speed and operate the spreader lever position.
Remember: Open the rate gate after the spreader is in motion at
operating speed (about 3 mph., or at a brisk walking pace).
Close the rate gate while spreader is still at operational speed.
8
Advertisement
Table of Contents
