Step 3 Ac Mains Lead Connection; Step 4 Preparing The Remote Control; Step 5 Easy Setup - Panasonic SC-XH50 Operating Instructions Manual

step 3 AC mains lead connection
To household mains socket
AC mains lead
(supplied)
BE SURE TO READ THE CAUTION FOR THE AC
MAINS LEAD ON PAGE 2 BEFORE CONNECTION.
Conserving power
This unit consumes a small amount of power, even when
it is in standby mode (approx. 0.8 W). To save power
when the unit is not to be used for a long time, unplug it
from the household mains socket.
You will need to reset some memory items when plugging
back this unit.
The supplied AC mains lead is for use with this unit only.
Do not use it with other equipment. Also, do not use cords for
other equipment with this unit.
step 4 Preparing the remote control
Batteries
Insert so the poles (r and j) match those in the
remote control.
R6/LR6, AA
Replace the cover.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer's instructions.
≥Use alkaline or manganese batteries.
≥Do not heat or expose to flame.
≥Do not leave the battery(ies) in an automobile
exposed to direct sunlight for a long period of time with
doors and windows closed.
Do not:
≥mix old and new batteries.
≥use different types of batteries at the same time.
≥take apart or short circuit.
≥attempt to recharge alkaline or manganese batteries.
≥use batteries if the covering has been peeled off.
Mishandling of batteries can cause electrolyte leakage
which can severely damage the remote control.
Remove the batteries if the remote control is not going to be
used for a long period of time. Store in a cool, dark place.
Use
Aim at the remote control signal sensor (
obstacles.
Distance: Within approx. 7 m
Angle: Within approx. 20° up and down, approx. 30° to
the left and right
This unit (rear)
AC IN
Press in and lift up.
4), avoiding
step 5 Easy setup
The Easy setup screen assists you in making
necessary settings.
Preparation
Turn on your TV and select the appropriate video input
mode
(e.g. VIDEO 1, AV 1, HDMI, etc.) to suit the connection
to this unit.
≥To change your TV's video input mode, refer to its
operating instructions.
≥This remote control can perform some basic TV
operations ( 4).
1
Press [Í]1 to turn on the unit.
≥The Easy setup screen appears automatically.
2
Press [3, 4]8 to select "Yes" and press [OK]8.
3
Follow the messages and make the settings with
[3, 4, 2, 1]8 and [OK]8.
≥Language
Select the language used on menu screen.
≥TV aspect
Select the aspect to suit your TV.
≥Speaker layout
Select "Surround layout (Recommended)" mode or
"Front layout (Alternative)" mode according to your
speaker layout ( 6, Installation).
≥Speaker check
Listen to speaker output to confirm speaker
connections.
≥Speaker output
Make surround sound setting for speaker output.
≥TV audio
Select the audio input connection from your TV.
For AUX connection (
For HDMI connection (
For SCART (AV) connection (
This will be the TV audio setting for VIERA Link
"HDAVI Control". (
4
Press [OK]8 to finish the "Easy setup".
≥You can perform this setup anytime by selecting "Easy setup"
in the Setup menu. ( 20)
≥If this unit is connected to a "HDAVI Control 3 or later"
compatible TV via HDMI cable, the menu language and TV
aspect information will be retrieved via VIERA Link.
≥If this unit is connected to a "HDAVI Control 2" compatible TV
via HDMI cable, the menu language information will be
retrieved via VIERA Link.
8): Select "AUX".
8): Select "ARC".
8): Select "AV".
16)
9