Page 1
Before operating this unit, please read this manual thoroughly and retain it for future reference. Mode d’emploi Page 116 Avant la mise en service de cet appareil, prière de lire attentivement ce mode d’emploi que l’on conservera pour toute référence ultérieure. UP-2300 UP-2800 1997 by Sony Corporation...
Page 2
Owner’s Record The model and serial numbers are located at the rear. Record these number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. Serial No. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture.
Tabel of Contents Introduction About This Manual ............5 System Overview .............. 7 System Configuration............8 Operation Before Printing ..............9 Loading an Ink Ribbon Cartridge ........9 Loading Paper ..............12 Selecting the Input Signal ..........14 Making Full-Size Printouts ..........16 Making Multiple Copies of Identical Printouts ....
Page 4
Tabel of Contents Installation and Setting Up the Printer ............. 68 Adjustment Compensating for the Input Signals ....... 69 Matching the Video Monitor Color to (Continued) the Printer Color ............72 Adjusting the Printout Color .......... 75 Changing the Printout Size/Printout Area ...... 82 Selecting the Operation Mode for Automatic Printing Capabilities..............
In this manual, the UP-2800 is used for illustrations. Also, the monitor display and printer window display are used to explain the operation. If your printer is a UP-2300 which is not equipped with the printer window display, perform operations according to the monitor display explanation.
Page 6
About This Manual (continued) Conventions used Cross references Throughout this manual you will find references to other sections of the manual that contain related information. Important note Be sure to read the sections of the manual marked Note . They explain points that Note you should be aware of to operate the printer correctly and prevent malfunctions.
System Overview The UP-2300/2800 color video printer is designed for capturing images from video equipment such as VTR and for printing out high-resolution images, either in 256 shades in full color (about 300 dpi). You can make various types of printouts. You can also add a caption onto the printout.
System Overview (continued) System Configuration The following shows an example printer system configuration. Video source Provides the video input for printing. Connect a video source such as video recorder, video disk player Video monitor or similarly. Displays the images received from the video source (source image) and the image to be printed (memory source).
Operation Before Printing This section describes the following operations that must be made prior to starting printing after mounting the paper tray and paper cover on the printer and making the necessary connections. • Loading an ink ribbon cartridge (see below) •...
Page 10
Before Printing (continued) Note Never put your hand into the ink ribbon compartment. The thermal head becomes very hot. You may burn yourself if you touch it. When the ink ribbon cartridge cannot be ejected Turn the power off, then back on again. Then, after a while, press the ink ribbon cartridge.
Page 11
Notes When using ink ribbon cartridge • Once an ink ribbon cartridge has been completely used, replace it. Ink ribbon cartridges are not reusable. • Do not touch the ink ribbon cartridge or place it in a dusty location. Finger prints or dust on the ink ribbon will result in imperfect printing or malfunction of the head.
Before Printing (continued) Loading Paper To load paper, follow the procedure below. Be careful not to touch the printing surface. Notes • When loading the paper while the printer is operating, do not turn off the power. Turning off the power will cause the image stored in memory to be lost. •...
Page 13
Printing surface Place the paper in the paper tray with the printing surface facing up Riffle the paper Set the paper securely under the tab. Front Slide the paper tray back into the printer until it clicks into place. Close the front panel. Notes When handling the paper Do not touch the printing surface.
Before Printing (continued) Selecting the Input Signal Before printing, select the input signal (the input connector to which the signal to be printed is being input—VIDEO, S-VIDEO, or RGB (only for the UP-2800). Once you have selected the input signal, this setting remains effective until you select another source.
Page 15
Select INPUT SEL by pressing the ◊ or √ button. I NP U T SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / I NP U T SE L V I DEO/ SV / RGB H U E I NP U T S E L :...
Making Full-Size Printouts This section explains how to make a full-size printout. The operations described here constitute the basic procedure for making a printout. Before making a full-size printout • All connections should have already been made. (see page 65) •...
Page 17
Press the CAPTURE button at the instant when the image you want to print appears on the screen. The image is captured into memory. The memory image is displayed on the screen. Which image appears after this, the source image or memory image, depends on the setting made with AUTO LIVE on the FUNCTION SETUP menu (page 36).
Page 18
Making Full-Size Printouts (continued) Note • Do not turn off the power during printing. If you do so, paper may not be ejected and may jam in the printer. • Do not pull the paper from the paper cover until printing has been completed. •...
Making Multiple Copies of Identical Printouts You can make up to 9 copies of identical printouts. The following two methods are available to set the number of printouts. • On the menu • Using the PRINT QTY button. However, you cannot decrease the number of printouts.
Page 20
Making Full-Size Printouts (continued) Select PRINT QTY by pressing the ◊ or √ button. PR I N T E R SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / P R I N T QT Y I N TE R V A L OF F / ON...
Page 21
Setting the print out quantity by using the PRINT QTY button 1, 2 Press the PRINT QTY button. The following screen appears. If you do not perform any operation after you press the PRINT QTY button, the currently set number of copies appears for 2 or 3 seconds, after which it disappears.
Making Full-Size Printouts (continued) Capturing Another Image While Printing While the printer is printing, you can capture another image into another memory page to be printed once the printer becomes free, if you select field memory mode (page 29). Select the desired memory page by pressing the MEMORY PAGE button. Pressing the MEMORY PAGE button switches the memory page.
Page 23
Press the PRINT button. The image captured in step 2 is queued. The image is printed as soon as all previous printing jobs have been completed. Q1 A 1 Q 1 A 1 Memory page whose image has been queued for printing (blinks white on the video monitor) The memory page display returns to white on the video monitor once printing has been completed.
Making Variations of Printouts You can store various kinds of images into memory and make variations of printouts using the images captured into memory. Variations of printouts that the printer can produce The following variations of printout of the images stored in memory can be made. Printout of a full-size Printout of two Printout of four...
Selecting the Printer Application Mode The unit allows you to make printouts according to your need, such as regular printouts, printouts for identification photograph and printouts for sticker. You can select the application mode of the printer on the SYSTEM SETUP menu. When you use the printer first time, the standard application mode for regular printouts is selected.
Page 26
Making Variations of Printouts (continued) Select SYSTEM by pressing the ◊ or √ button. PR I N T E R SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / P R I N T QT Y I N TE R V A L OF F / ON...
Page 27
Select the desired application mode by pressing the ı or ∫ button. S Y S T EM SE T UP CO L OR n n n P R N SE TUP P RE S S L C D – CN TR. B AUD RA TE / 24 /4800 / 96 B EE P...
Making Variations of Printouts (continued) About the Memory To make printouts, it is first necessary to capture the image into memory. When capturing the image, there are two ways to use the memory, one is frame mode and the other is field mode. Frame mode: A image is captured in one memory.
Selecting the memory mode Note You can select the desired memory page only when 1 or 2H is selected in STANDARD mode. 1, 5 2, 4 Press the MENU button. The menu just before opened appears. Select LAY by pressing the ı or ∫ button. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY...
Page 30
Making Variations of Printouts (continued) Select MEMORY by pressing the ◊ or √ button. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X...
Page 31
Selecting a memory page MEMORY PAGE button To select a memory page, press the MEMORY PAGE button. Q1 A 1 Q 1 A 1 Press the MEMORY PAGE button as many times as the necessary until the desired memory page appears. Note The memory page whose image is being printed is blinking on the video monitor screen.
Making Variations of Printouts (continued) Making a Printout of Multiple Different Reduced Images You can store multiple images into a memory page and make a printout with those reduced images. This section explains how to make a printout with multiple reduced images.
Page 33
Select MULTI PIX by pressing the ◊ or √ button. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X 1 / 2H / 4 / 16 MU L T I P I X :...
Page 34
Making Variations of Printouts (continued) Select SEPARATE by pressing the ◊ or √ button. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X...
Page 35
To select the desired type of reduced-image printout using the MULTI PICTURE button You can select the number of reduced images using the MULTI PICTURE button on the front panel. 1, 2 Press the MULTI PICTURE button. The current setting appears. The video monitor screen is reset to the regular screen after a few seconds.
Page 36
Making Variations of Printouts (continued) Selecting how to capture the images You can select how to capture the images by using the PRINTER SETUP menu and FUNCTION SETUP menu. • Storing only the image currently displayed on the video monitor screen or storing images sequentially to all reduced-image positions of a memory page at regular intervals.
Page 37
Select INTERVAL by pressing the ◊ or √ button. PR I N T E R SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / P R I N T QT Y I N TE R V A L OF F / ON GA MMA...
Page 38
Making Variations of Printouts (continued) Press the ∫ button. The FUNCTION SETUP menu appears. F UNC T I ON S E T U P CO L OR : n n n P R N SE TUP P RE S S A U T O L I V E OF F / ON I MME D .
Page 39
Making a Printout with Multiple Reduced Images This subsection explains how to make printouts of multiple reduced images taking, as an example, the making of a printout of four reduced images. Before making the printout of four reduced images • Select the type of the four-reduced image and whether to put the white borders (see page 32) •...
Page 40
Making Variations of Printouts (continued) Press the CAPTURE button at the instant the image you want to print appears on the screen. The image has been stored to the star (*) that blinked green on the video monitor screen or the position number displayed on the printer window display in step 1.
Page 41
2 Start the video source. If the memory image is displayed, press the SOURCE/MEMORY button to display the source image. 3 Press the CAPTURE button at the instant the image you want to print appears. The previously stored image is replaced with the newly stored image. To skip a previously captured image When an image has already been captured, the previously captured image can be replaced by pressing the CAPTURE button.
Making Variations of Printouts (continued) Making Printouts for Stickers The unit supports application modes such as STICK DUP or STICK DIF that allows you to make printouts for stickers. • STICK DUP application mode allows you to make a printout with four or 16 identical reduced images.
The UPA-2002 (not supplied) is required. For detailed information, contact your Sony dealer. Making printouts for identification photographs of a desired size The FLEX IPP application mode allows you to select the size of one image. The number of images in a single printout depends on the set size.
Page 44
Making Variations of Printouts (continued) p To decide the size The sizes can be registered as LOAD SIZE number 1, 2 and 3. The printer retains these sizes even if you turn off the printer power. Once you have set the typical size of the photograph, you can make the identification photograph with the desired size very easily.
Page 45
Select WINDOW by pressing the ◊ or √ button. L A Y OU T S E T U P COL OR / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X 1 / 2H / 4 / 16 S E P A RA T E...
Page 46
Making Variations of Printouts (continued) Decide the size. Display the source image on the video monitor and decide the size as watching the image trimmed according to the size. Wide (determined by the setting of H WIDTH) The image is trimmed according to the size.
Page 47
Select the SAVE SIZE number to which new settings are to be stored by pressing the ı or ∫ button. W I NDOW S E T U P CO L OR : n n n L A Y SE T U P P R E S S L OA D S I Z E 1 / 2 / 3...
Page 48
Making Variations of Printouts (continued) Select the memory page by pressing the MEMORY PAGE button. Load the desired size by pressing the MULTI PICTURE button. By pressing the MULTI PICTURE button, ”LOAD SIZE: 1/2/3 appears. Each time you press the MULTI PICTURE button, the LOAD SIZE number to be loaded changes.
Page 49
Making printouts for identification photograph with the fixed-size image The printer allows you to make a printout with a full-size image, 4 or 16 identical reduced images in FIXED IPP application mode. You can select the number of identical reduced images on the menu on the LAYOUT SETUP menu.
Making Printouts With a Caption A caption, such as data or comments, can be added to a printout below the image. You can input up to 48 characters. About the CAPTION menu A caption is entered from the CAPTION menu. You can input caption in any printer application mode and make a printout with a caption.
Entering a Caption Enter a caption as follows. The setting remains effective until you enter a new setting - even if you turn the power off. Notes • If you turn off the power of the printer without returning to the LAYOUT SETUP menu or regular screen, the entered characters are cleared.
Making Printouts With a Caption (continued) Select CAPTION by pressing the ◊ or √ button. L A Y OU T S E T U P COL OR / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X...
Page 53
Select the character you want to enter by pressing the ◊, √, ı or ∫ button. Example: To enter S C A P T I ON ON Display S by pressing the ◊, √, ı or ∫ button. C. ON A B CDE F GH I J K L MN O PQR S T U VWX Y Z 01 23456789 + –...
Page 54
Making Printouts With a Caption (continued) To enter a space 1 Position the green cursor to the point where you want to enter a space by performing the operations explained in step 5. 2 Select SPC by pressing the ◊, √, ı or ∫ button. 3 Press the EXEC button.
Page 55
Select exit by pressing the ◊, √, ı or ∫ button. Press the EXEC button. The entered characters are stored in the memory. The LAYOUT SETUP menu appears. To return to the regular screen Press the MENU button in step 9. The entered characters are stored in the memory and the regular screen appears.
Deleting the Images Stored to Memory Pages You can delete images captured to memory pages, form either all of memory pages or a single memory page, by using the CLEAR button. Whether images of all memory pages or single memory page are deleted depends on the setting of CLEAR on the FUNCTION SETUP menu.
Page 57
Press the ∫ button. The FUNCTION SETUP menu appears. FU NC T I ON S E T UP CO L OR n n n P R N SE T UP PRE SS A U T O L I V E OF F / ON I MME D .
Page 58
Deleting the Images Stored to Memory Pages (continued) Select PRINTER SETUP by pressing the ◊ or √ button. FU NC T I ON S E T UP CO L OR n n n P R N SE T UP PRE SS A U T O L I V E OF F / ON I MME D .
Deleting Images You can delete images captured to memory pages, either from all memory pages or a single memory pages. If the source image is displayed on the video monitor, press the CLEAR button once so that the memory image will be displayed. Deleting images in all memory pages simultaneously Before deleting images in all memory pages Set CLEAR to ALL on the FUNCTION SETUP menu.
Page 60
Deleting the Images Stored to Memory Pages (continued) Deleting images in a certain memory page Before deleting images Set CLEAR to PAGE on the FUNCTION SETUP menu. Press the SOURCE/MEMORY button when the source image is displayed on the video monitor screen. The image stored in memory is displayed on the screen.
Installation and Adjustment Supplied Accessories The printer is packed together with the following accessories. Check that nothing is missing from your package. Paper cover (1) Paper tray (1) AC power cord (1) Color printing pack Warranty card (1) Operating Instructions (1) a) Use the ink ribbon cartridge and paper for operation check.
Supplied Accessories (continued) Assembly Attach the supplied paper cover, paper tray and ink ribbon cartridge to the printer. For details of how to assemble them, see the pages given in parentheses. Printer Ink ribbon cartridge (page 9) Paper tray (page 12) Paper cover Installation and Adjustment...
Preparing the Remote Control Unit The following remote control units (not supplied) allow you to control the printer remotely. • RM-5500 Remote Control Unit: Used to connect to the REMOTE 1 connector • RM-91 Remote Control Unit, FS-20/36 Foot switch: Used to connect to the REMOTE 2 connector.
Page 64
Supplied Accessories (continued) Using the RM-5500 remote control unit (not supplied) as a wireless unit When using the remote control unit as a wireless unit, aim the head of the remote control unit at the remote sensor on the printer. With fresh batteries, the range of the remote control unit is about 3 meters.
Connections To enable printing, video equipment to act as an input signal source, and a video monitor to display images or menus must be connected. The following diagrams illustrate how to make the input, output and remote control connections. Use this as a guide when connecting the necessary signals to and from the equipment to be used for printing.
Connections (continued) Making Connections for Viewing Images to be Printed Connect a video monitor to view stored images and to check those to be printed. Connect the necessary video monitor which will be used in actual printing, using the following diagram as a guide. INPUT SYNC S-VIDEO...
Making Connections to Enable Remote Control The printer can be controlled remotely by connecting the RM-5500 Remote Control Unit (not supplied), RM-91 Remote Control Unit (not supplied), the FS-20/36 Foot Switch (not supplied) or the personal computer. Computer RS-232C cable SMF-1015 to RS-232C UP-2800 INPUT...
Setting Up the Printer You can set up the printer specification. Once you have adjusted and stored, the printer operates according to the setting until those values are modified. You can set up the printer according to the intended purpose, connected equipment or your individual preferences.
This section explains the following settings and adjustments. • Compensating for the input signals (on this page) • Matching the video monitor color to the printout color (page 72) • Adjusting the printout color and sharpness (page 75) • Adjusting the tone of the printout (page 80) •...
Page 70
Setting Up the Printer (continued) Press the MENU button, then select INPUT SETUP menu by pressing the ◊ or √ button. I NP U T SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / I NP U T SE L V/ SV / RGB H U E...
Page 71
1 Press the ◊ or √ button until the desired item appears. CO L OR I NP U T SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / I NP U T SE L V/ SV / RGB H U E...
Setting Up the Printer (continued) Matching the Video Monitor Color to the Printout Color To match the color of the monitor image to that of the printout, adjust the monitor and printer colors such that the monitor color is the same as that of the printout. The printer outputs either of two kinds of video signals according to the printer settings.
Page 73
Press the MENU button, then select OUTPUT SETUP menu by pressing the ı or ∫ button. OU T P U T SE T UP CO L OR n n n / COL / LA Y / PR N / I N / OUT / D I S P L A Y OF F / ON SOURCE...
Page 74
Setting Up the Printer (continued) Adjust the monitor while comparing the printout with the image on the monitor. 1 Select the adjustment item by pressing the ◊ or √ button. 2 Perform adjustment by pressing the ı or ∫ button. Menu When selecting Button to be...
Adjusting the Printout Color You can adjust the printout quality by adjusting the color intensity, printout sharpness and tone (GAMMA) of the printout. Adjusting the color intensity, contrast and sharpness You can adjust the color intensity (RED/GREEN/BLUE), contrast (DARK/ LIGHT) and printout sharpness. You can store up to three settings. These settings are managed according to the LOAD COLOR number.
Page 76
Setting Up the Printer (continued) Select LOAD COLOR by pressing the ◊ or √ button. CO L OR A D J U S T CO L OR : n n n / COL / LA Y / PRN / I N / OUT / L OA D CO L OR 1 / 2 / 3 CYN–RED...
Page 77
When adjusting the RED/GREEN/BLUE (color intensity) Menu Adjustment When selecting Button to be Adjustment direction on item pressed the menu CYN-RED To make the image reddish ∫ button Toward RED To make the image cyan (blue ) ı button Toward CYN (cyan) MAG-GRN To make the image magenta (pink) ∫...
Page 78
Setting Up the Printer (continued) When adjusting the sharpness You can set the sharpness to any of 5 steps from 1 to 5. A setting of step 3 corresponds to the standard sharpness. When selecting Content of settings To make a soft outline Toward step 1 To make a normal outline Centered (step 3)
Page 79
Select the SAVE COLOR number to which new settings are to be stored by pressing the ı or ∫ button. CO L OR A D J U S T CO L OR : n n n / COL / LA Y / PRN / I N / OUT / L OA D CO L OR 1 / 2 / 3 CYN–RED...
Page 80
Setting Up the Printer (continued) Adjusting the tone of the printout You can adjust the tone so that the details in the white or black part is clearly printed. Note The tone (GAMMA) setting is activated only when the UPC-2010 color printing pack or UPC-2020 B/W printing pack is used.
Page 81
Select the desired tone pressing the ı or ∫ button. CO L OR A D J U S T CO L OR : n n n / COL / LA Y / PRN / I N / OUT / L OA D CO L OR 1 / 2 / 3 CYN–RED MA G –...
Setting Up the Printer (continued) Changing the Printout Size/Printout Area When you print an image that is narrower or wider than the standard screen size, a black frame may be printed or the image may be partially cut. In such a case, you can change the screen size.
Page 83
Select WINDOW by pressing the ◊ or √ button. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X 1 / 2H / 2 / 4 / 16 S E P A RA T E...
Page 84
Setting Up the Printer (continued) When a black line appears on the printout Adjust the printout area according to the position of the line on the printout, by using the H START and V START items on the menu. Position where Menu adjustment Button to be Adjustment result...
In addition to the above, the printer can be remotely controlled by a pulse signal input to REMOTE 2. (see pages 101). Also, you can control the printer using the personal computer. For detailed information on controlling with the computer, contact with your Sony dealer. 2, 3, 4, 5, 6, 7 Press the MENU button, then select PRINTER SETUP menu by pressing the ı...
Page 86
Setting Up the Printer (continued) Select FUNCTION by pressing the ◊ or √ button. PR I N T E R S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / P R I N T QT Y I N TE R V A L OF F / ON...
Page 87
Select the desired timing to capture the image by pressing the ı or ∫ button. Timing Selection To capture the image just after the CAPTURE command is received To capture the image with the timing pulse input to REMOTE 2 connector a) When IMMED.
Page 88
Setting Up the Printer (continued) Select the function that you want to assign to the remote control unit connected to the REMOTE 2 connector by pressing the ı or ∫ button. Items to be selected Operation PRINT Printing whenever you press the switch. C &...
Erasing the Screen Display You can erase a screen display with the menu when, for example, it is hard to see the image that is hidden behind the screen display . The printer operation is identical, regardless of whether screens are displayed. The same messages are displayed in the printer window display.
Page 90
Setting Up the Printer (continued) Select OFF by pressing the ı or ∫ button. OU T P U T SE T UP CO L OR n n n / COL / LA Y / PR N / I N / OUT / D I S P L A Y OF F / ON SOURCE...
Adjusting the Brightness of the Printer Window Display When it is hard to read the contents of the printer window display, adjust the brightness with the menu. This item is available only for the UP-2800. 2, 3, 4, 5, 6 Press the MENU button, then select PRINTER SETUP menu by pressing the ı...
Page 92
Setting Up the Printer (continued) Press the ∫ button. The SYSTEM SETUP menu appears. S Y S T E M S E T U P CO L OR n n n P R N SE TUP P RE S S L C D –...
Selecting Whether the Operation and Error Tones Sound Whenever you press a button on the front panel or sub panel, the operation tone sounds (one time). When an error occurs, the alarm tone sounds (three times). You can turn these tones on and off with menu. 2, 3, 4, 5, 6 Press the MENU button, then select PRINTER SETUP menu by pressing the ı...
Page 94
Setting Up the Printer (continued) Press the ∫ button. The SYSTEM SETUP menu appears. S Y S T E M S E T U P CO L OR n n n P R N SE TUP P RE S S L C D –...
Setting the Baud Rate for Computer Communication When controlling the printer with a computer connected to the printer’s RS-232C connector, select the appropriate baud rate. For details, contact your nearest Sony dealer. 2, 3, 4, 5, 6 Press the MENU button, then select PRINTER SETUP menu by pressing the ı...
Page 96
Setting Up the Printer (continued) Press the ∫ button. The SYSTEM SETUP menu appears. S Y S T E M S E T U P CO L OR n n n P R N SE TUP P RE S S L C D –...
• If the unit malfunctions or if a foreign body falls into the cabinet, disconnect the power immediately and consult your Sony service facility or your Sony dealer. Installation •...
Precautions (continued) Location To prevent internal heat built-up, leave enough room around the printer for air to circulate through the vents on the left hand side of the cabinet. On transportation Do not transport the printer with the supplied accessories. Doing so may cause malfunction.
Ink Ribbon Cartridge and Paper Both paper and an ink ribbon cartridge are necessary for printing. Use the ink ribbon with the paper contained in the same package. UPC-2010 Color Printing Pack Contains color ink ribbon cartridge and paper. Color ink ribbon cartridge 1 roll A-6 (4 ⁄...
Specifications Power requirements S VIDEO (Separate luminance (Y) and 120 V AC, 50/60 Hz chrominance (C) signals): 4-pin mini-DIN 1 Power consumption About 1.8 A max. at 25°C, Y: 1 Vp-p 120 V AC C: 0.29 Vp-p color burst Operating temperature 75 ohms (terminated), sync negative 5°C to 35°C (41°F to 95°F)
Page 101
Using the automatic printing capabilities Note (REMOTE 2) When AUTO LIVE of the FUNCTION-SETUP If you send the remote control pulse signals menu is set to OFF, the memory image is illustrated through the REMOTE 2 connector, the displayed on the screen after the image is captured printer is remotely controlled according to the in memory.
(page 124) The paper tray has got out of position. MECHA TROUBLE: TRAY MECHA TROUBLE TRAY Contact your Sony service facility or your Sony dealer to clear error status. MECHA TROUBLE: PLATEN MECHA TROUBLE PLATEN The paper has jammed inside the printer.
Message Possible cause and remedies On the monitor In the printer window display INSERT RIBBON AND PAPER INSERT RIBBON The ink ribbon cartridge and paper are not loaded. n Load the ink ribbon cartridge and paper. (pages 9 and 12) SET PAPER REMOVE PRINTS REMOVE PRINTS...
Error/Warning Messages (continued) If the paper jams If the paper jams after pressing the PRINT button, the message stating that paper jammed appears on the video monitor and in the printer window display. Follow the steps below to remove the jammed paper. When the jammed paper is removed, you do not need to continue operation explained below.
Page 105
When the message does not appear, you can use the printer as normal. However, the image captured to memory have been cleared. Capture the image to memory again. If the same message appears again, the printer must not be operated. Turn off the power immediately and contact your Sony service facility. Others...
Before proceeding with these trouble checks, first check that the power cord is firmly connected. Should the problem persist, unplug the unit and contact your Sony dealer or local authorized Sony service facility.
Location and Function of Parts and Controls For details, refer to the pages given in parentheses. Front 1 U POWER switch (13) 5 PRINT lamp Press to turn the printer on or off. Lights while the printer is printing. 2 Top cover (on the top panel) 6 ALARM lamp (103) Do not open this top cover.
Location and Function of Parts and Controls (continued) PRINT QTY (quantity) button (21) When the front panel is open Press this button to set the number of copies. You can set any number up to 9. You can change the number even when the printer is printing.
Sub Panel STOP CLEAR DISPLAY MENU EXEC 1 STOP button (18) CLEAR button (59, 60) Press to stop printing midway. By pressing Press this button to clear the images captured in the memory pages. Which images that can this button, the current printing complete and printing after this is cancelled.
3 RS-232C connector (67) connectors. Used to connect the computer to control the a) Only for the UP-2800. printer. For details, contact your nearest Sony dealer. 4 INPUT (input signal) connectors (65) Used to connect the video equipment supplying the source image.
Monitor Display There are two types of display: the regular screen display and menu screen display. The two types of display are explained using the monitor display. Regular screen display When you first turn on the printer, the regular screen message appears. 4 Printer operation mode display section Display Meaning...
Location and Function of Parts and Controls (continued) Menu screen Menu screen tree chart The menu screen configuration is shown using the tree-chart. For details, refer to the pages indicated in ( ). COLOR ADJUST menu (page 75) CO L OR A D J U S T CO L OR : n n n / COL / LA Y / PRN / I N / OUT / L OA D CO L OR 1 / 2 / 3...
Index A, B F, G, H P, Q Accessaries (supplied) 61 Foot switch 63, 67, 85 Paper Adjusting Full-size printout inkr ribbon and paper 99 input signal 69 making 16 loading 12 color of the printer’s output signal 72 setting 33 notes on storing 13 printout area 82 FUNCTION SETUP menu 38, 57, 86...
Page 114
Index (continued) R, S Remote control unit (not supplied) foot switch 63, 67, 85 remote control unit 63, 67, 85 Safety precautions 97 Screen display erasing 89 erasing temporarily 18 Selecting the input signal 14 Setting up the printer with menu adjusting the printer window display brightness 91 adjusting the printout color 75...
Page 116
Français AVERTISSEMENT Pour prévenir tout risque d’incendie ou d’électrocution, garder cet appareil à l’abri de la pluie et de l’humidité. Pour prévenir tout risque d’électrocution, ne pas ouvrir le boîtier. Confier l’entretien de cet appareil exclusivement à un personnel qualifié.
Page 117
Table des matières Introduction A propos de ce mode d’emploi ........119 Vue d’ensemble du système ........121 Configuration système ..........122 Opération Avant l’impression ............123 Installation d’une cassette à ruban encreur ....123 Chargement du papier d’impression ......126 Sélection du signal d’entrée .........
Page 118
Table des matières (suite) Installation et Raccordement pour permettre la commande à distance de l’imprimante ......... 181 réglage Configuration de l’imprimante ........182 (suite) Compensation pour les signaux d’entrée ..... 183 Harmonisation des couleurs du moniteur avec les couleurs de l’imprimante ........186 Réglage des couleurs des tirages ........
De même, l’écran du moniteur et la fenêtre d’affichage de l’imprimante sont utilisés pour expliquer les modes de fonctionnement. Si votre imprimante est une UP-2300 sans fenêtre d’affichage, exécutez les opérations en suivant les instructions sur l’écran du moniteur. Toute différence de fonctionnement ou de paramètres entre les modèles susmentionnés est clairement expliquée dans le présent mode d’emploi.
Page 120
A propos de ce mode d’emploi (suite) Installation et réglage Description des raccordements et des réglages au moyen des menus affichés sur le moniteur vidéo et sur la fenêtre d’affichage de l’imprimante. Lorsque tous les raccordements et réglages auront été effectués, il ne sera plus nécessaire de recommencer ces opérations durant les opérations d’impression normales.
Vue d’ensemble du système Les imprimantes vidéo couleur de la série UP-2300/2800 ont été conçues pour saisir des images provenant d’appareils vidéo tels qu’un magnétoscope et pour imprimer des images à haute résolution, que ce soit en 256 teintes ou en quadrichromie (environ 300 ppp).
Vue d’ensemble du système (suite) Configuration système Voici un exemple de configuration système intégrant cette imprimante. Source vidéo Fournit l’entrée vidéo en vue de l’impression. Raccordez-y une source vidéo comme un magnétoscope, un lecteur Moniteur vidéo de vidéodisques ou tout Affiche les images transmises autre appareil similaire.
Opération Avant l’impression Cette section présente une description des opérations à exécuter avant de lancer une impression et après avoir installé le magasin à papier et le réceptacle à papier sur l’imprimante et procédé aux raccordements indispensables. • Installez une cassette à ruban encreur •...
Page 124
Avant l’impression (suite) Retirez la cassette à ruban encreur en appuyant sur la touche dessus. La cassette à ruban encreur s’éjecte. Cette opération n’est pas nécessaire la première fois que vous utilisez l’imprimante. Remarque N’introduisez jamais les doigts dans le compartiment du ruban encreur. La tête thermique atteint en effet une température très élevée et vous risquez de vous brûler si vous la touchez.
Page 125
Introduisez fermement la cassette à ruban encreur jusqu’à ce qu’elle s’encliquette. Si la cassette à ruban encreur ne peut être introduite Mettez successivement l’imprimante hors et puis à nouveau sous tension. Introduisez ensuite le porte-ruban encreur. Refermez le panneau frontal. Remarques Utilisation des cassettes à...
Avant l’impression (suite) Chargement du papier d’impression Pour charger du papier, appliquez la procédure ci-dessous. Veillez à ne pas toucher la surface d’impression du papier. Remarques • Ne mettez pas l’imprimante hors tension lorsque vous chargez du papier d’impression. Sinon, les images enregistrées dans la mémoire seront perdues. •...
Page 127
Surface d’impression Placez le papier d’impression dans le magasin à papier avec la surface d’impression (face lisse sans inscriptions) vers le haut. Déramez le papier. Glissez correctement le papier sous l’onglet. Avant Réintroduisez le magasin à papier dans l’imprimante jusqu’à ce qu’il s’encliquette.
Avant l’impression (suite) Sélection du signal d’entrée Avant d’exécuter un tirage, sélectionnez le signal d’entrée (le connecteur d’entrée via lequel le signal à imprimer est transmis — VIDEO, S-VIDEO ou RGB (UP- 2800 uniquement). Lorsque vous avez sélectionné le signal d’entrée, ce réglage reste opérant jusqu’à...
Page 129
Sélectionnez INPUT SEL en appuyant sur la touche ◊ ou √. I NP U T SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / I NP U T SE L V I DEO/ SV / RGB H U E I NP U T S E L :...
Réalisation de tirages pleine page Cette section explique comment réaliser des tirages pleine page. Les opérations décrites ci-après constituent la procédure de base pour la réalisation de tirages. Avant d’exécuter un tirage pleine page • Tous les raccordements doivent déjà avoir été réalisés (voir page 179). •...
Page 131
Appuyez sur la touche CAPTURE au moment où l’image que vous voulez imprimer apparaît à l’écran. L’image est saisie dans la mémoire. L’image mémoire est affichée sur l’écran. L’image qui s’affiche après celle-là, à savoir l’image source ou l’image mémoire, dépend du réglage effectué avec AUTO LIVE dans le menu FUNCTION SETUP (page 154).
Page 132
Réalisation de tirages pleine page (suite) Remarques • Ne mettez pas l’imprimante hors tension durant une impression. Sinon, il se peut que le papier ne soit pas éjecté et reste coincé dans l’imprimante. • Ne tirez pas le papier du réceptacle à papier avant que l’impression soit terminée. •...
Réalisation de plusieurs copies de tirages identiques Vous pouvez imprimer jusqu’à 9 copies d’un même tirage. Appliquez l’une des deux méthodes suivantes pour définir le nombre de tirages. • Dans le menu • Utilisez la touche PRINT QTY. Vous ne pouvez pas diminuer le nombre de tirages.
Page 134
Réalisation de tirages pleine page (suite) Sélectionnez PRINT QTY en appuyant sur la touche ◊ ou √. PR I N T E R SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / P R I N T QT Y I N TE R V A L OF F / ON...
Page 135
Définition du nombre de copies à l’aide de la touche PRINT QTY 1, 2 Appuyez sur la touche PRINT QTY. L’écran suivant apparaît. Si vous n’exécutez aucune opération après avoir appuyé sur la touche PRINT QTY, le nombre de copies sélectionné apparaît pendant 2 ou 3 secondes, après quoi il disparaît.
Réalisation de tirages pleine page (suite) Saisie d’une autre image pendant une impression Pendant une impression, vous pouvez saisir une autre image dans une autre page mémoire et elle sera imprimée dès que l’imprimante sera libre, si vous sélectionnez le mode de mémoire de champ (page 143). Sélectionnez la page mémoire voulue en appuyant sur la touche MEMORY PAGE.
Page 137
Appuyez sur la touche PRINT. L’image saisie à l’étape 2 est mise dans la file d’attente. L’image est imprimée dès que tous les travaux d’impression précédents ont été réalisés. Q1 A 1 Q 1 A 1 Page mémoire dont l’image a été mise dans la file d’attente d’impression (clignote en blanc sur le moniteur vidéo) L’écran de page mémoire redevient blanc sur le moniteur vidéo lorsque l’impression est terminée.
Variantes de tirages Vous pouvez enregistrer différents types d’images dans la mémoire et effectuer des variantes de tirages à l’aide des images saisies dans la mémoire. Variantes de tirages que l’imprimante peut produire Vous pouvez réaliser les variantes de tirages au départ des images enregistrées dans la mémoire.
A propos du mode d’application L’appareil vous permet de réaliser des tirages en fonction de vos besoins, comme des tirages ordinaires, des tirages pour photos d’identité et des tirages pour étiquettes adhésives. Vous pouvez sélectionner le mode d’application de l’imprimante dans le menu SYSTEM SETUP.
Page 140
Variantes de tirages (suite) Sélectionnez SYSTEM en appuyant sur la touche ◊ ou √. PR I N T E R SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / P R I N T QT Y I N TE R V A L OF F / ON...
Page 141
Sélectionnez le mode d’application voulu en appuyant sur la touche ı ou ∫. S Y S T EM SE T UP CO L OR n n n P R N SE TUP P RE S S L C D – CN TR. B AUD RA TE / 24 /4800 / 96 B EE P...
Variantes de tirages (suite) A propos de la mémoire Pour réaliser des tirages, il convient en premier lieu d’enregistrer l’image dans la mémoire. Pour la saisie de l’image, vous avez deux possibilités d’utiliser la mémoire, à savoir le mode d’image et le mode de champ. Mode d’image: Une image est saisie dans une mémoire.
Page 143
Sélection du mode de mémoire Remarque Vous pouvez sélectionner la page mémoire uniquement lorsque 1 ou 2H est sélectionné en mode STANDARD. 1, 5 2, 4 Appuyez sur la touche MENU. Le dernier menu consulté apparaît. Sélectionnez LAY en appuyant sur la touche ı ou ∫. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY...
Page 144
Variantes de tirages (suite) Sélectionnez MEMORY en appuyant sur la touche ◊ ou √. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X...
Page 145
Sélection d’une page mémoire Touche MEMORY PAGE Pour sélectionner une page mémoire, appuyez sur la touche MEMORY PAGE. Q1 A 1 Q 1 A 1 Appuyez sur la touche MEMORY PAGE autant de fois qu’il est nécessaire pour que la page mémoire voulue apparaisse.
Variantes de tirages (suite) Réalisation d’un tirage à images multiples différentes en réduction Vous pouvez enregistrer des images multiples dans une page mémoire et réaliser une impression de ces images en réduction. Cette section vous explique comment réaliser une impression d’images multiples en réduction. Appliquez la procédure ci-dessous pour réaliser une impression d’images multiples en réduction.
Page 147
Sélectionnez MULTI PIX en appuyant sur la touche ◊ ou √. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X 1 / 2H / 4 / 16...
Page 148
Variantes de tirages (suite) Sélectionnez SEPARATE en appuyant sur la touche ◊ ou √. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X...
Page 149
Pour sélectionner le type d’impression d’images en réduction voulu à l’aide de la touche MULTI PICTURE Vous pouvez sélectionner le nombre d’images réduites à l’aide de la touche MULTI PICTURE du panneau frontal. 1, 2 Appuyez sur la touche MULTI PICTURE. Le réglage sélectionné...
Page 150
Variantes de tirages (suite) Sélection du mode d’enregistrement des images Vous pouvez sélectionner comment enregistrer les images à l’aide du menu CONF. IMPRIM et du menu CONF. FONCTION. • Mémorisation de l’image affichée sur l’écran du moniteur vidéo uniquement ou mémorisation séquentielle d’images dans toutes les pages mémoire à...
Page 151
Sélectionnez INTERVAL en appuyant sur la touche ◊ ou √. PR I N T E R SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / P R I N T QT Y I N TE R V A L OF F / ON GA MMA...
Page 152
Variantes de tirages (suite) Appuyez sur la touche ∫. Le menu FUNCTION SETUP apparaît. F UNC T I ON S E T U P CO L OR : n n n P R N SE TUP P RE S S A U T O L I V E OF F / ON I MME D .
Page 153
Réalisation d’un tirage à images multiples en réduction Cette sous-section vous explique comment réaliser des tirages d’images multiples en réduction. A titre d’exemple, nous vous expliquons comment réaliser un tirage de quatre images en réduction. Avant de réaliser le tirage de quatre images en réduction •...
Page 154
Variantes de tirages (suite) Appuyez sur la touche CAPTURE au moment où l’image que vous voulez imprimer apparaît à l’écran. L’image a été enregistrée sous l’étoile (*) qui clignotait en vert sur l’écran du moniteur vidéo ou sous le numéro de position indiqué dans la fenêtre d’affichage de l’imprimante à...
Page 155
3 Appuyez sur la touche CAPTURE au moment où l’image que vous voulez imprimer apparaît. L’image précédemment mémorisée à cet endroit est remplacée par la nouvelle image enregistrée. Pour sauter une image précédemment mémorisée Si une image a déjà été mémorisée, l’image précédemment mémorisée peut être remplacée en appuyant sur la touche CAPTURE.
Variantes de tirages (suite) Réalisation de tirages pour étiquettes adhésives L’imprimante supporte les modes d’application tels que STICK DUP ou STICK DIF permettant de réaliser des tirages pour étiquettes. • Le mode d’application STICK DUP vous permet de réaliser un tirage avec quatre ou seize images réduites identiques.
Par conséquent, le magasin à papier fourni est trop étroit pour charger du papier. Le UPA-2002 (non fourni) est indispensable. Pour plus d’informations détaillées, adressez-vous à votre revendeur Sony. Réalisation de tirages pour photos d’identité dans un format déterminé Le mode d’application FLEX IPP vous permet de sélectionner le format d’une image.
Page 158
Variantes de tirages (suite) p Pour déterminer le format Les formats peuvent être enregistrés sous les numéros LOAD SIZE 1, 2 et 3. L’imprimante conserve ces formats en mémoire même lorsque vous la mettez hors tension. Dès que vous avez déterminé le format de la photo, vous pouvez réaliser très facilement les photos d’identité...
Page 159
Sélectionnez WINDOW en appuyant sur la touche ◊ ou √. L A Y OU T S E T U P COL OR / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X 1 / 2H / 4 / 16 S E P A RA T E...
Page 160
Variantes de tirages (suite) Déterminez le format. Affichez l’image source sur le moniteur vidéo et déterminez le format en visionnant l’image détourée au format sélectionné. Largeur (déterminé par le réglage de H WIDTH) L’image est rognée en Hauteur (déterminé fonction du format. par le réglage de V L’image de cette partie WIDTH)
Page 161
Sélectionnez le numéro SAVE SIZE sous lequel les nouveaux réglages doivent être enregistrés en appuyant sur la touche ı ou ∫. W I NDOW S E T U P CO L OR : n n n L A Y SE T U P P R E S S L OA D S I Z E 1 / 2 / 3...
Page 162
Variantes de tirages (suite) Sélectionnez la page mémoire en appuyant sur la touche MEMORY PAGE. Chargez le format voulu en appuyant sur la touche MULTI PICTURE. Lorsque vous appuyez sur la touche MULTI PICTURE, l’indication ”LOAD SIZE: 1/2/3 apparaît. Chaque fois que vous appuyez sur la touche MULTI PICTURE, le numéro LOAD SIZE à...
Page 163
Réalisation de tirages pour photos d’identité au format fixe L’imprimante vous permet de réaliser, avec une image pleine page, 4 ou 16 images multiples identiques en réduction dans le mode d’application FIXED IPP. Vous pouvez sélectionner le nombre d’images réduites identiques dans le menu LAYOUT SETUP.
Réalisation de tirages avec une légende Une légende, comme une date ou des commentaires, peuvent être ajoutées sous l’image en vue du tirage. Vous pouvez introduire jusqu’à 48 caractères. A propos du menu CAPTION Les légendes sont saisies via le menu CAPTION. Vous pouvez introduire une légende dans n’importe quel mode d’application de l’imprimante et réaliser un tirage avec une légende.
Saisie d’une légende Introduisez une légende selon la procédure suivante. Le réglage reste effectif jusqu’à ce que vous introduisiez un nouveau réglage - même si vous mettez l’imprimante hors tension. Remarques • Si vous mettez l’imprimante hors tension sans revenir au menu LAYOUT SETUP ou à...
Page 166
Réalisation de tirages avec une légende (suite) Sélectionnez CAPTION en appuyant sur la touche ◊ ou √. L A Y OU T S E T U P COL OR / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X...
Page 167
Sélectionnez le caractère que vous voulez introduire en appuyant sur la touche ◊, √, ı ou ∫. Exemple: Pour introduire la lettre “S” C A P T I ON ON Affichez “S” en appuyant sur la touche ◊, √, ı ou ∫. C.
Page 168
Réalisation de tirages avec une légende (suite) Pour introduire un espace 1 Positionnez le curseur vert sur la position où vous voulez introduire un espace en exécutant les opérations expliquées à l’étape 5. 2 Sélectionnez SPC en appuyant sur la touche ◊, √, ı ou ∫. 3 Appuyez sur la touche EXEC.
Page 169
Sélectionnez exit en appuyant sur la touche ◊, √, ı ou ∫. Appuyez sur la touche EXEC. Les caractères introduits sont enregistrés dans la mémoire. Le menu LAYOUT SETUP apparaît. Pour revenir à l’écran normal Appuyez sur la touche MENU à l’étape 9. Les caractères introduits sont enregistrés dans la mémoire et l’écran normal apparaît.
Suppression des images enregistrées dans les pages mémoire Vous pouvez effacer les images enregistrées dans les pages mémoire, soit de toutes les pages mémoire soit d’une seule page mémoire à l’aide de la touche CLEAR. L’effacement des images de toutes les pages mémoire ou d’une seule page mémoire est déterminé...
Page 171
Appuyez sur la touche ∫. Le menu FUNCTION SETUP apparaît. FU NC T I ON S E T UP CO L OR n n n P R N SE T UP PRE SS A U T O L I V E OF F / ON I MME D .
Page 172
Suppression des images enregistrées dans les pages mémoire (suite) Sélectionnez PRINTER SETUP en appuyant sur la touche ◊ ou √. FU NC T I ON S E T UP CO L OR n n n P R N SE T UP PRE SS A U T O L I V E OF F / ON...
Suppression d’images Vous pouvez effacer les images enregistrées dans des pages mémoire, soit de toutes les pages mémoire soit d’une seule page mémoire. Si l’image source est affichée sur le moniteur vidéo, appuyez une fois sur la touche CLEAR de façon à ce que l’image mémoire soit affichée. Suppression simultanée des images de toutes les pages mémoire Avant de supprimer les images de toutes les pages mémoire Réglez CLEAR sur ALL dans le menu FUNCTION SETUP.
Page 174
Suppression des images enregistrées dans les pages mémoire (suite) Suppression des images d’une page mémoire déterminée Avant de supprimer les images Réglez CLEAR sur PAGE dans le menu FUNCTION SETUP. Appuyez sur la touche SOURCE/MEMORY lorsque l’image source est affichée sur l’écran du moniteur vidéo. L’image enregistrée dans la mémoire est affichée sur l’écran.
Installation et réglage Accessoires fournis L’imprimante est fournie avec les accessoires suivants. Vérifiez bien si rien ne manque dans le conditionnement de votre imprimante. Réceptacle à papier (1) Magasin à papier (1) Cordon d’alimentation (1) Jeu d’impression couleur Carte de garantie (1) Mode d’emploi (1) a) Utilisez la cassette à...
Accessoires fournis (suite) Assemblage Installez le réceptacle à papier, le magasin à papier et la cassette à ruban encreur fournis sur l’imprimante. Pour plus de détails sur la manière de les assembler, reportez-vous aux pages indiquées entre parenthèses. Printer Cassette à ruban encreur (page 123) Magasin à...
Préparation de la télécommande Les télécommandes suivantes (non fournies) vous permettent de commander l’imprimante à distance. • Télécommande RM-5500: A raccorder au connecteur REMOTE 1. • Télécommande RM-91, commande au pied FS-20/36: A raccorder au connecteur REMOTE 2. Les opérations pouvant être commandées à distance au moyen des télécommandes ci-dessus dépendent de la sélection du mode de commande à...
Page 178
Accessoires fournis (suite) Utilisation de la télécommande RM-5500 (non fournie) comme télécommande sans fil Si vous utilisez la télécommande comme une télécommande sans fil, dirigez la tête de la télécommande vers le capteur de télécommande de l’imprimante. Avec des piles neuves, la télécommande offre une portée efficace d’environ 3 mètres. Utilisation de la télécommande RM-91/FS-20/36 (non fournie) Le fonctionnement de la télécommande RM-91 et de la commande au pied FS-20 peut être contrôlé...
Raccordement Pour permettre l’impression, l’appareil vidéo doit servir de source de signal d’entrée et vous devez raccorder un moniteur vidéo pour afficher les images ou les menus. Les diagrammes suivants présentent comment établir les raccordements d’entrée, de sortie et de commande à distance. Utilisez-les comme guides de référence pour la connexion des signaux requis de et vers l’appareil à...
Raccordement (suite) Raccordement pour la visualisation des images à imprimer sur un moniteur vidéo Raccordez un moniteur vidéo pour pouvoir visualiser les images mémorisées et contrôler celles qui doivent être imprimées. Raccordez le moniteur vidéo qui sera utilisé pour l’impression proprement dite en utilisant le diagramme suivant comme guide de référence.
Raccordement pour permettre la commande à distance de l’imprimante Cette imprimante peut être commandée à distance en raccordant une télécommande RM-5500 (non fournie), une télécommande RM-91 (non fournie), une commande au pied FS-20/36 (non fournie) ou un ordinateur personnel. Ordinateur Câble RS-232C SMF-1015 vers RS-232C UP-2800...
Configuration de l’imprimante Vous pouvez configurer les spécifications de l’imprimante. Lorsque vous avez réglé et mémorisé les paramètres voulus, l’imprimante fonctionne conformément à ces paramètres jusqu’à ce que vous les modifiiez à nouveau. Vous pouvez régler l’imprimante en fonction de l’utilisation que vous comptez en faire, d’un appareil raccordé...
Cette section explique les réglages et ajustements suivants. • Compensation pour les signaux d’entrée (page 183) • Harmonisation des couleurs du moniteur avec les couleurs d’impression (page 186) • Réglage de la couleur et de la netteté des tirages (intensité et contraste de l’image) (page 189) •...
Page 184
Configuration de l’imprimante (suite) Appuyez sur la touche MENU et sélectionnez ensuite le menu INPUT SETUP en appuyant sur la touche ◊ ou √. I NP U T SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / I NP U T SE L V/ SV / RGB H U E...
Page 185
1 Appuyez sur la touche ◊ ou √ jusqu’à ce que le paramètre voulu apparaisse. CO L OR I NP U T SE T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / I NP U T SE L V/ SV / RGB H U E...
Configuration de l’imprimante (suite) Harmonisation des couleurs du moniteur avec les couleurs de l’imprimante Pour harmoniser les couleurs de l’image affichée sur le moniteur avec celles des tirages, réglez les couleurs du moniteur et de l’imprimante de façon à ce que les couleurs du moniteur soient identiques à...
Page 187
Appuyez sur la touche MENU et sélectionnez ensuite le menu OUTPUT SETUP en appuyant sur la touche ı ou ∫. OU T P U T SE T UP CO L OR n n n / COL / LA Y / PR N / I N / OUT / D I S P L A Y OF F / ON SOURCE...
Page 188
Configuration de l’imprimante (suite) Réglez le moniteur en comparant le tirage avec l’image affichée sur le moniteur. 1 Sélectionnez le paramètre à régler en appuyant sur la touche ◊ ou √. 2 Procédez au réglage en appuyant sur la touche ı ou ∫. Paramètre de Pour sélectionner Touche à...
Réglage des couleurs des tirages Vous pouvez ajuster la qualité des tirages en réglant l’intensité des couleurs, la netteté ainsi que la tonalité (GAMMA) des tirages. Réglage de l’intensité des couleurs, du contraste et de la netteté Vous pouvez régler l’intensité des couleurs (RED/GREEN/BLUE), le contraste (DARK/LIGHT) et la netteté...
Page 190
Configuration de l’imprimante (suite) Sélectionnez LOAD COLOR en appuyant sur la touche ◊ ou √. CO L OR A D J U S T CO L OR : n n n / COL / LA Y / PRN / I N / OUT / L OA D CO L OR 1 / 2 / 3 CYN–RED...
Page 191
Réglage de RED/GREEN/BLUE (intensité des couleurs) Paramètre de Pour sélectionner Touche à Sens de réglage dans le réglage du menu actionner menu CYN-RED Pour rendre l’image rougeâtre Touche ∫ Vers RED Pour rendre l’image cyan (bleue) Touche ı Vers CYN (cyan) MAG-GRN Pour rendre l’image magenta (rose) Touche ∫...
Page 192
Configuration de l’imprimante (suite) Réglage de la netteté Vous pouvez régler la netteté sur l’une des 5 graduations allant de 1 à 5. Le réglage sur la graduation 3 correspond à la netteté standard. Pour sélectionner Valeur de réglage Pour obtenir des contours adoucis Vers la graduation 1 Pour obtenir des contours normaux Centre (graduation 3) Pour obtenir des contours nets...
Page 193
Pour conserver la valeur de réglage initiale Sélectionnez un numéro SAVE COLOR différent du numéro LOAD COLOR sélectionné à l’étape 3. Appuyez sur la touche EXEC. Les réglages sont enregistrés sous le numéro SAVE COLOR sélectionné à l’étape 6. L’indication TEMP disparaît du menu. Appuyez sur la touche MENU.
Page 194
Configuration de l’imprimante (suite) Réglage de la tonalité des tirages Vous pouvez régler la tonalité de façon à ce que les détails des parties blanches ou noires apparaissent clairement sur les tirages. Remarque Le réglage de la tonalité (GAMMA) n’est activé que quand le jeu d’impression couleur UPC-2010 ou le jeu d’impression noir et blanc UPC-2020.
Page 195
Sélectionnez la tonalité voulue en appuyant sur la touche ı ou ∫. CO L OR A D J U S T CO L OR : n n n / COL / LA Y / PRN / I N / OUT / L OA D CO L OR 1 / 2 / 3 CYN–RED...
Configuration de l’imprimante (suite) Changement du format d’impression/zone d’impression Lorsque vous imprimez une image plus étroite ou plus large que la taille de l’écran standard, il se peut qu’un cadre noir soit imprimé ou que l’image soit partiellement coupée. Dans ce cas, vous pouvez changer le format de l’écran. Il se peut également qu’une ligne noire apparaisse sur les tirages même si elle n’apparaît pas sur le moniteur vidéo.
Page 197
Sélectionnez WINDOW en appuyant sur la touche ◊ ou √. L A Y OU T S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / MEMORY F R AME / F I E L D MUL T I P I X 1 / 2H / 2 / 4 / 16 S E P A RA T E...
Page 198
Configuration de l’imprimante (suite) Si une ligne noire apparaît sur les tirages Ajustez le format d’impression en fonction de la position de la ligne sur les tirages à l’aide des paramètres H START et V START du menu. Position où la ligne Paramètre de Touche à...
Vous pouvez également commander l’imprimante à l’aide d’un ordinateur personnel. Pour plus de détails sur la commande de l’imprimante à l’aide d’un ordinateur personnel, consultez votre revendeur Sony. 2, 3, 4, 5, 6, 7 Appuyez sur la touche MENU et sélectionnez ensuite le menu PRINTER SETUP en appuyant sur la touche ı...
Page 200
Configuration de l’imprimante (suite) Sélectionnez FUNCTION en appuyant sur la touche ◊ ou √. PR I N T E R S E T UP CO L OR n n n / COL / LA Y / PRN / I N / OUT / P R I N T QT Y I N TE R V A L OF F / ON...
Page 201
Remarque Pour commander l’imprimante à distance à l’aide de la télécommande, réglez le paramètre IMMED.CAP du menu FUNCTION SETUP sur OFF. FU NC T I ON S E T UP CO L OR n n n P R N SE TU P P R E S S A U TO L I V E OF F / ON...
Page 202
Configuration de l’imprimante (suite) Sélectionnez la fonction que vous voulez attribuer à la télécommande raccordée au connecteur REMOTE 2 en appuyant sur la touche ı ou ∫. Paramètres à sélectionner Opération PRINT Impression par une pression sur la touche. C & PRINT Saisie d’une image dans une page mémoire et impression d’une (CAPTURE &...
Suppression de l’affichage à l’écran Vous pouvez supprimer un affichage à l’écran à l’aide du menu si, par exemple, il est difficile de voir l’image dissimulée par un affichage à l’écran. Le fonctionnement de l’imprimante est identique, que des affichages soient à l’écran ou non.
Page 204
Configuration de l’imprimante (suite) Sélectionnez OFF en appuyant sur la touche ı ou ∫. OU T P U T SE T UP CO L OR n n n / COL / LA Y / PR N / I N / OUT / D I S P L A Y OF F / ON SOURCE...
Réglage de la luminosité de la fenêtre d’affichage de l’imprimante S’il est difficile de lire le contenu de la fenêtre d’affichage de l’imprimante, réglez- en la luminosité à l’aide du menu. Ce paramètre est uniquement disponible sur le modèle UP-2800. 2, 3, 4, 5, 6 Appuyez sur la touche MENU et sélectionnez ensuite le menu PRINTER SETUP en appuyant sur la touche ı...
Page 206
Configuration de l’imprimante (suite) Appuyez sur la touche ∫. Le menu SYSTEM SETUP apparaît. S Y S T E M S E T U P CO L OR n n n P R N SE TUP P RE S S L C D –...
Sélection de l’activation des bips de confirmation et d’erreur Chaque fois que vous appuyez sur une touche du panneau frontal ou du panneau secondaire, un bip de confirmation est émis (une fois). Lorsqu’une erreur survient, le bip d’erreur retentit (trois fois). Vous pouvez activer et désactiver ces bips à l’aide du menu.
Page 208
Configuration de l’imprimante (suite) Appuyez sur la touche ∫. Le menu SYSTEM SETUP apparaît. S Y S T E M S E T U P CO L OR n n n P R N SE TUP P RE S S L C D –...
Lorsque vous commandez l’imprimante au départ d’un ordinateur personnel raccordé via le connecteur RS-232C de l’imprimante, sélectionnez le débit en bauds approprié. Pour plus de détails, consultez votre revendeur Sony. 2, 3, 4, 5, 6 Appuyez sur la touche MENU et sélectionnez ensuite le menu PRINTER SETUP en appuyant sur la touche ı...
Page 210
Configuration de l’imprimante (suite) Appuyez sur la touche ∫. Le menu SYSTEM SETUP apparaît. S Y S T E M S E T U P CO L OR n n n P R N SE TUP P RE S S L C D –...
étoffe, etc. • Si l’imprimante fonctionne incorrectement ou si un corps étranger pénètre à l’intérieur du châssis, déconnectez immédiatement le cordon d’alimentation secteur et consultez votre revendeur Sony. Installation • N’installez pas l’appareil dans un endroit soumis à: — des vibrations mécaniques;...
Précautions (suite) A propos de la condensation • Si l’imprimante est soumise à des variations de température brutales et importantes comme lors de son transfert d’une pièce froide dans une pièce chaude ou lorsqu’elle est laissée dans une pièce dont le système de chauffage tend à...
Cassette à ruban encreur et papier d’impression Pour réaliser des impressions, vous avez besoin de papier d’impression et d’une cassette à ruban encreur. Utilisez le ruban encreur et le papier d’impression emballés dans le même conditionnement. Ensemble pour impression couleur UPC-2010 Contient une cassette à...
Spécifications Puissance de raccordement S VIDEO (signaux de luminance (Y) et de chrominance (C) séparés): 120 V CA, 50/60 Hz miniconnecteur DIN à 4 broches 1 Consommation électrique Y: 1 Vcc Approx. 1,8 A max. à 25 °C, 120 V CA C: Impulsion de synchronisation Température d’utilisation couleur 0,29 Vcc...
Page 215
Télécommande RM-91 Remarque Commande au pied FS-20 Si AUTO LIVE dans le menu FUNCTION- Commande au pied FS-36 SETUP est réglé sur OFF, l’image mémoire est affichée sur l’écran après qu’elle a été enregistrée Exploitation de la fonction d’impression dans la mémoire. Dans ce cas, appuyez sur la (REMOTE 2) touche SOURCE/MEMORY chaque fois que vous Si vous envoyez les signaux d’impulsion de...
(page 218). MECHA TROUBLE: TRAY Le bac d’alimentation est sorti de son logement. MECHA TROUBLE Consultez le service après-vente Sony ou votre revendeur Sony pour TRAY remédiez à ce problème. Le papier s’est coincé à l’intérieur de l’imprimante.
Page 217
Message Causes possibles et remèdes Sur le moniteur Dans la fenêtre d’affichage de l’imprimante INSERT RIBBON AND La cassette à ruban encreur et le papier n’ont pas été chargés. INSERT RIBBON PAPER nChargez la cassette à ruban encreur et du papier (pages 123 et SET PAPER 126).
Messages d’erreur/avertissement (suite) En cas de bourrage du papier Si un bourrage papier se produit après que vous avez appuyé sur la touche PRINT, le message signalant un bourrage de papier apparaît sur le moniteur vidéo et dans la fenêtre d’affichage de l’imprimante. Appliquez la procédure suivante pour dégager le papier coincé.
Page 219
Si la cassette à ruban encreur ne peut être enlevée, l’imprimante ne peut plus être utilisée. Mettez-la immédiatement hors tension et consultez le service après-vente Sony. Réintroduisez le bac d’alimentation, le réceptacle à papier ou la cassette à ruban encreur que vous avez enlevée et refermez le panneau frontal.
Avant de procéder à ces contrôles, vérifiez toutefois si le cordon d’alimentation est correctement branché. Si le problème persiste, mettez l’imprimante hors tension et consultez votre revendeur Sony ou le service après- vente agréé. Symptômes Causes possibles et remèdes...
Emplacement et fonction des composants et des commandes Pour plus de détails, reportez-vous aux pages indiquées entre parenthèses. Partie frontale 1 Commutateur POWER U (128) 4 Capteur de télécommande (178) Appuyez sur ce commutateur pour mettre Dirigez l’avant de la télécommande vers ce l’imprimante sous ou hors tension.
Page 222
7 Témoin MULTI PICTURE !™ Touche PRINT (149, (131, 132, 137, 155, 155, 162) 157, 162, 163) Appuyez sur cette touche pour sélectionner le Appuyez sur cette touche pour réaliser une type de tirage voulu. Lorsque vous appuyez impression. sur cette touche, le type de tirage sélectionné s’allume en vert pendant deux ou trois !£...
Emplacement et fonction des composants et des commandes (suite) Panneau secondaire STOP CLEAR DISPLAY MENU EXEC 4 Touche CLEAR (173, 174) 1 Touche STOP (132) Appuyez sur cette touche pour interrompre un Appuyez sur cette touche pour effacer les images enregistrées dans les pages mémoire. cycle d’impression.
3 Connecteur RS-232C (181) 6 Connecteurs OUTPUT (180) Sert au raccordement d’un ordinateur pour Servent au raccordement du moniteur vidéo. commander l’imprimante. Pour plus de détails, consultez votre revendeur Sony. Connecteur Appareils pouvant être raccordés Appareil vidéo doté d’un connecteur de S-VIDEO 4 Connecteurs INPUT (signal d’entrée)
Affichage du moniteur Il y a deux types d’affichages: l’écran normal et l’écran de menu. Les deux types d’affichage sont expliqués à l’aide d’écrans. Ecran normal Lorsque vous mettez l’imprimante sous tension pour la première fois, le message d’écran normal apparaît. 4 Section d’affichage du mode de fonctionnement de l’imprimante Affichage...
Page 226
Emplacement et fonction des composants et des commandes (suite) Ecran de menu Organigramme de l’écran de menu La configuration de l’écran de menu est illustrée à l’aide d’un organigramme. Pour plus de détails, reportez-vous aux pages indiquées entre parenthèses. Menu COLOR ADJUST (page 189) CO L OR A D J U S T CO L OR : n n n / COL / LA Y / PRN / I N / OUT /...
Index si le papier est épuisé en cours d’impression 137 Accessoires (fournis) 175 Débit en bauds pour la communication si l’image mémorisée est floue 131 avec l’ordinateur 209 Accessoires fournis si l’imprimante n’imprime pas 132 accessoires fournis 175 Dépannage 220 si une ligne noire apparaît sur les montage 176 tirages 132...
Page 228
Réglage couleurs d’impression 189 couleurs du signal de sortie de l’imprimante 186 netteté des tirages 192 signal d’entrée 183 taille de l’écran 198 tonalité d’impression 194 zone d’impression 196 Réglage du nombre de tirages 133 Sony Corporation Printed in Japan...