Table of Contents
Advertisement
Quick Links
AUTOMATIC
BATTERY CHARGER
93781
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INjURY,
REAd ANd UNdERSTANd ALL WARNINGS
ANd INSTRUCTIONS BEFORE USE.
Copyright
2005 by Harbor Freight Tools
. All rights reserved. No portion of this manual or any
©
®
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Chicago Electric 93781
Summary of Contents for Chicago Electric 93781
-
Page 1: Battery Charger
TO PREVENT SERIOUS INjURY, REAd ANd UNdERSTANd ALL WARNINGS ANd INSTRUCTIONS BEFORE USE. Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this manual or any © ® artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. -
Page 2: Work Area
HANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: Model______________ SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. -
Page 3: Personal Safety
There is an increased risk of electric shock if your body is grounded. do not abuse the Power Cord. Never use the Power Cord to carry the Battery Charger or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. -
Page 4: Grounded Tools: Tools With Three Prong Plugs
Battery Charger. Never remove the grounding prong from the plug. do not use the Battery Charger if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. -
Page 5: Extension Cords
INSULATEd APPLIANCES: APPLIANCES WITH TWO PRONG PLUGS Note: The Battery Charger has a Two Prong Plug. Appliances marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the... - Page 6 Specific Safety Rules for the Battery Charger Maintain labels and nameplates on the Battery Charger. These carry important information. If the labels are unreadable or missing, contact Harbor Freight Tools for replacement. Always place the Battery Charger on a dry, flat, level, sturdy nonflammable work surface capable of supporting the weight of the Battery Charger.
- Page 7 12 volt. Always locate the Battery Charger as far away from the battery as the Charger’s dC cables permit. Never place the Battery Charger directly above the battery being charged. Gases from the battery will corrode and damage the Battery Charger.
- Page 8 Battery Charger in a closed-in area, or restrict ventilation in any way. do not set a battery on top of the Battery Charger. Connect and disconnect dC output clamps only after removing the AC power cord from the electrical outlet.
- Page 9 When unpacking the Automatic Battery Charger, check to make sure parts on page 11 are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. determine which post of the battery is grounded (connected) to the chassis vehicle.
- Page 10 Note: The monitoring voltage of the Battery Charger is 10.5V; if the voltage is below 10.5V, the Battery Charger will not work. A battery must be properly connected to the charger to allow it to work. For best results, the capacity of the battery should be below 24 Ah.
- Page 11 Battery Charger. With a dry cloth, remove any oil and residue from the Battery Charger after each use. Do not clean with flammable or corrosive liquids.
-
Page 12: Parts List
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 93781 For technical questions please call 1-800-444-3353. Parts List...
Need help?
Do you have a question about the 93781 and is the answer not in the manual?
Questions and answers