Chicago Electric 94533 Operating Instructions
Chicago Electric 94533 Operating Instructions

Chicago Electric 94533 Operating Instructions

Chicago electric maintenance battery charger operating instructions 12 volt / 2 amp output

Advertisement

Quick Links

MAINTENANCE BATTERY CHARGER
Copyright
©
sheet or any artwork contained herein may be reproduced in any shape or form without
Always wear ANSI-approved safety impact eye goggles during setup or use.
1.
Maintain a safe working environment. Always keep the work area free of obstruc-
2.
tions, grease, oil, trash, and other debris. Do not use this product in areas near
flammable chemicals, dust, and vapors.
Read and understand all instructions and safety precautions as outlined in the
3.
manufacturer's manual of the battery with which this product will be used.
4.
FIRE HAZARD! Never allow the red and black Battery Clamps to touch each
other or the same metal object.
WARNING! Lead acid batteries generate hydrogen gas during normal operation,
5.
and even more gas is generated when the battery is charging. Hydrogen gas is
explosive and highly flammable. Never smoke near a charging battery.
6.
Plug the Charger into its electrical outlet only after it is connected to the
vehicle's battery.
Do not attempt to start a vehicle with the Charger connected to its battery.
7.
WARNING! If battery fluid comes in contact with skin, wash with soap and water and
8.
rinse with lemon juice and vinegar. If the fluid comes into contact with eyes, flush
with water for several minutes and contact a physician immediately. Never burn a
battery as it can explode in a fire. Do not attempt to charge a leaking battery.
WARNING! People with pacemakers should consult their physician(s) before using
9.
this product. Electromagnetic fields in close proximity to a heart pacemaker could
cause interference or failure of the pacemaker. In addition, people with pacemakers
should adhere to the following: Caution is necessary when near the coil, spark plug
wires, or distributor of a running engine.
12 Volt / 2 Amp Output

OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
2006 by Harbor Freight Tools
the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
SAVE THESE INSTRUCTIONS

SAFETY WARNINGS AND PRECAUTIONS

94533
®
. All rights reserved. No portion of this instruction
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 94533 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Chicago Electric 94533

  • Page 1: Operating Instructions

    Caution is necessary when near the coil, spark plug wires, or distributor of a running engine. 12 Volt / 2 Amp Output 94533 3491 Mission Oaks Blvd., Camarillo, CA 93011 . All rights reserved. No portion of this instruction ®...
  • Page 2 Then disconnect the BLACK/NEGATIVE (–) Battery Clamp from the Temporary Connection Cord (8) from the NEGATIVE battery terminal of the vehicle’s battery. Make sure to store all parts of the Battery Charger in a clean, dry, safe location out of reach of children.
  • Page 3 Plug the Power Cord (2) of the Battery Charger into the nearest 120 volt, grounded, electrical outlet. The RED (AC Power) light on the Main Unit (1) of the Battery Charger should be illuminated. This light indicates the Main Unit is receiving 120 volt electrical power from the electrical outlet.
  • Page 4 Problem: The Battery Charger is plugged into an electrical outlet, but no lights on the Main Unit (1) are illuminated. Possible Solutions: Check to make sure the Power Cord (2) is properly plugged into a working 120 volt, grounded electrical outlet.
  • Page 5 This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 For technical questions, please call 1-800-444-3353 SKU 94533 PAGE 5...

Table of Contents