Setting The Channels And Clock - Panasonic Diga DMR-EH59EM Operating Instructions Manual

Setting the Channels and Clock

Preparation:
 Turn on the mains for the television
(and connected equipment) and
select the appropriate AV input to
suit the connections to this unit.
 These are the first settings you make
upon buying the unit. You don't need
to make these settings again.
to turn the unit on.

When connecting to a Q Link compatible TV with a fully wired 21-pin
Scart cable or a VIERA Link (HDAVI Control 3 or later) compatible TV
with an HDMI cable (
– You can download the tuning positions from the television for the
channels in this unit's channel coverage.
– This unit's Auto Clock Setting function synchronizes the time when the TV
channel that is broadcasting time and date information is tuned.
Power Save Function:
,  to select "On" or
"Off", then
OK
"On": It will go into the Power Save mode when the unit is in
standby mode.
"Off": It is possible to start quickly from the standby mode.
(Quick Start mode)
– The features of the power save function when the unit is in
standby mode are as below.
Power Save
Power consumption
Watching the picture from
the digital satellite receiver
connected to the AV2 terminal
Startup time
Front display
 It is possible to startup and start recording within several seconds.
Depending on the type of TV or the connected terminal, it may take time to
display the screen.
When setup has completed, the confi rmation screen appears.
OK
The Owner ID settings screen appears.
, then press the numbered buttons to
enter your choice of a 4-digit PIN number.
Make a note of the PIN number
(don't forget), as it is not possible
to return to the factory preset.
to store the PIN number.
OK
TV's remote control
42), downloading from the television starts.
Power Save
On: Minimise standby power
consumption, without
Quick Start function and
AV2 loop-through in standby.
SELECT
Off: With Quick Start
function and AV2 loop-through
OK
RETURN in standby.
On
Approx. 0.9 W
Cannot do
Not quick
Turns off
(The clock display
disappeared.)
PIN number
Name
House No.
Postcode
RETURN
RETURN : leave
(continued on the next page)
On
Off
Tips
 Auto-Setup
Off
Auto-Setup starts instead of "Download
from TV" in the following cases:
Approx. 9 W
– when connecting to a television with
the VIDEO OUT, S VIDEO OUT or
Can do
COMPONENT VIDEO OUT terminal
(
Quick  – when connecting to a television that
does not have the VIERA Link or Q Link
functions
Stays lighted
This function automatically tunes all
available TV stations and synchronizes
the time when the TV channel that is
broadcasting time and date information is
tuned. This takes about 8 minutes.
 To cancel setup
Press [RETURN].
 If the unit displays "No stations
found !"
Press [] to select "No", then press [OK].
Go to step . After you have performed
steps –, turn off the unit and confi rm
the cable or aerial input is connected
to the RF IN terminal. Restart the setup
again (
 If the clock setting menu appears or
Owner ID
the clock is not correct, set the clock
manually (
     
 Restarting the setup (
 To correct the PIN number
1. Press [, ] to select the digit.
2. Press the numbered buttons to enter
the digit.
 When this unit is not operated for
approximately 5 minutes while the screen
is being displayed, the screen saver may
be displayed.
You can turn this function off (
"Screen Saver").
TV


VOL
CH
DRIVE
SELECT
A A AV
2 3
1
CH
4 5 6
VIDEO Plus+
8 9
7
STATUS
DELETE INPUT
0
SELECT
SKIP SLOW/SEARCH
PLAY/x1.3
STOP PAUSE
TIME SLIP EXIT
OK
OPTION RETURN
CREATE
AUDIO DISPLAY MANUAL SKIP
CHAPTER
75)
67).
14).
67)
70,
13
RQT9272