General Issues Power; General Issues: Displays - Panasonic Diga DMR-EZ48VEB Operating Instructions Manual

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions
indicated in the chart do not solve the problem, consult your dealer for instructions.
The following does not indicate a problem with the unit:
 Regular disc/video cassette rotating sound.
 Poor reception due to atmospheric conditions.
 Image disturbance during search.
 Periodic interruptions to the reception due to satellite broadcasting breaks.
 Operations are slow to respond in power save mode.
Operations are not working due to a poor-quality disc. (Try again using a Panasonic disc.)
 The unit freezing due to the activation of one of its safety devices (
 When the unit is turned on or off, there may be an unexpected sound.
General Issues
No power.
The unit does not turn on pressing
[ DVD/VHS].
The unit switches to standby mode.
The unit is turned off automatically.
General Issues
The display is dim.
"0:00" is fl ashing on the unit's display.
The displayed time of this unit is
different from the actual recording
time or MP3 recording time.
The clock is not correct.
Compared to the actual recorded
time, the elapsed time displayed is
less.
(Only when recording in NTSC)
The tape counter is not changing.
The clock does not display on the
unit when switched to standby.
Power
 Insert the AC mains lead securely into a known active household mains socket.
 Linked timer recordings with external equipment is in recording standby
("EXT-L" on the unit's display blinks when [ DVD/VHS] is pressed). Press
[EXT LINK] to cancel the recording standby.
 One of the unit's safety devices is activated. Press [/I] on the main unit to
turn the unit on.
 If you connected this unit to a "HDAVI Control" compatible TV with an
HDMI cable, or connected this unit to a Q Link-compatible TV with a fully
wired 21-pin Scart cable, this unit will be automatically set to standby
mode when the TV is set to standby mode.
Displays
 Change "FL Display" in the Setup Menu.
 Set the clock.
 Times shown may disagree with actual times.
 [-R] [-R\DL] [+R] [+R]DL] The remaining capacity does not increase even if
titles are deleted.
 Available space on a DVD-RW (DVD-Video format) or +RW disc increases
when you delete the last title (space may increase slightly when you delete
other titles).
 If you record or edit about 200 times or more, the remaining capacity
of DVD-R, DVD-R DL, +R, and +R DL is reduced and then recording or
editing may be disabled (for the second layer on DVD-R DL and +R DL,
this happens after about 60 times).
 The time during searching may not be displayed accurately.
 Under adverse reception conditions, etc., the automatic time correction
function may not work.
In this case, "Automatic" is automatically turned to "Off". If re-setting the
Auto Clock Setting does not work, set the time manually.
 The displayed recording/play time is converted from the number of frames
at 29.97 frames (equal to 0.999 seconds) to one second. There will be a
slight difference between the time displayed and the actual elapsed time
(e.g., actual one-hour elapsed time may display as approximately 59
minutes 56 seconds). This does not affect the recording.
 The tape counter does not change while playing unrecorded parts. The
"second" display changes as follows:
(e.g., Blank after 1 h 36 min)
 The unit's display also appears like this if the tape is dirty or damaged.
Consult your dealer if this is the case.
Ensure "Power Save" is set to "Off".
80, To restore the unit if it freezes).
Page
8, 9, 70
27
−
46
Page
66
12
−
−
−
−
−
12
−
−
−
68
81
RQT9126