Advertisement
ENGLISH
1
Bolt
2
Drum
3
Planer blade
4
Drum cover
5
Adjusting plate
6
Blade edge
7
Screws
8
Heel
9
Back side of gauge base
10 Inside edge of gauge plate
11 Gauge plate
12 Gauge base
13 Pan head screw
14 Planer blade locating lugs
15 Heel of adjusting plate
16 Set plate
SAFETY INSTRUCTIONS
WARNING! When using electric tools, basic safety
precautions, including the following, should always
be followed to reduce the risk of fire, electric shock
and personal injury. Read all these instructions
before operating this product and save these instruc-
tions.
For safe operations:
1.
Keep work area clean.
Cluttered areas and benches invite injuries.
2.
Consider work area environment.
Do not expose power tools to rain. Do not use power
tools in damp or wet locations. Keep work area well
lit. Do not use power tools where there is risk to
cause fire or explosion.
3.
Guard against electric shock.
Avoid body contact with earthed or grounded sur-
faces(e.g. pipes, radiators, ranges, refrigerators).
4.
Keep children away.
Do not let visitors touch the tool or extension cord.
All visitors should be kept away from work area.
5.
Store idle tools.
When not in use, tools should be stored in a dry,
high or locked up place, out of reach of children.
6.
Do not force the tool.
It will do the job better and safer at the rate for which
it was intended.
7.
Use the right tool.
Do not force small tools or attachments to do the job
of a heavy duty tool. Do not use tools for purposes
not intended; for example, do not use circular saws
to cut tree limbs or logs.
8.
Dress properly.
Do not wear loose clothing or jewellery, they can be
caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors.
Wear protecting hair covering to contain long hair.
9.
Use safety glasses and hearing protection.
Also use face or dust mask if the cutting operation is
dusty.
6
Explanation of general view
17 Inside flank of gauge plate
18 Mini planer blade
19 Groove
20 Switch trigger
21 Lock button
22 Lock-off button
23 Start
24 End
25 Blade edge
26 Cutting line
27 Screw
28 Edge fence
29 ''V'' groove
30 Front base
31 Align the ''V'' groove with the
edge of the workpiece.
10. Connect dust extraction equipment.
ENA001-2
11. Do not abuse the cord.
12. Secure work.
13. Do not overreach.
14. Maintain tools with care.
15. Disconnect tools.
16. Remove adjusting keys and wrenches.
17. Avoid unintentional starting.
18. Use outdoor extension leads.
19. Stay alert.
32 Nozzle assembly
33 Chip cover screw
34 Chip cover
35 Fit pin on nozzle assembly into
this hole.
36 Sharpening holder
37 Wing nut
38 Blade (A)
39 Blade (B)
40 Side (C)
41 Side (D)
42 Limit mark
43 Screwdriver
44 Brush holder cap
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
Never carry the tool by the cord or yank it to discon-
nect it from the socket. Keep the cord away from
heat, oil and sharp edges.
Use clamps or a vice to hold the work. It is safer than
using your hand and it frees both hands to operate
the tool.
Keep proper footing and balance at all times.
Keep cutting tools sharp and clean for better and
safer performance. Follow instructions for lubrication
and changing accessories. Inspect tool cord periodi-
cally and if damaged have it repaired by an autho-
rized service facility. Inspect extension cords
periodically and replace, if damaged. Keep handles
dry, clean and free from oil and grease.
When not in use, before servicing and when chang-
ing accessories such as blades, bits and cutters.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
When tool is used outdoors, use only extension
cords intended for outdoor use.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
Advertisement
