Table of Contents
Advertisement
Available languages
Available languages
Multi-Brand Control Feature
Advanced Connections
Multi-Brand Control Setup
Audio/Video connection
The Remote Control can be set to control some TV functions.
If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR
to them to receive higher quality picture and sound.
1
Find your TV Brand Code Number from those shown below.
2
Set up for TV control,
➛ hold down TV button,
➛ enter code with NUMBER keys.
3
Confirm code entry,
➛ press POWER to turn your TV on or off.
VCR
• See table below for controllable functions in each mode.
AUDIO OUT
Notes
Notes
R
• Repeat setup after remote battery replacement.
L
• Remote will not control every TV made by the manufacturer listed. If you get no response, your particular
unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed,
then the remote is not compatible with that product.
VIDEO OUT
Using Multi-Brand Control
After remote is set up, you can select VCR or TV for the desired function.
Press VCR or TV on the remote.
(Table below shows available unit buttons for each mode.)
1
Connect the VCR's VIDEO OUT jack to the TV's VIDEO IN jack.
Unit
VCR
TV
Mode
All
VCR
VOL UP/DOWN
2
VCR/TV, PLAY, STOP, EJECT, SAP/Hi-Fi, DISPLAY,
POWER, INPUT,
Connect VCR's L/R AUDIO OUT jacks to the TV's L/R AUDIO IN jacks.
TV
FF, REW, PAUSE/SLOW, REC, SPEED, CM/ZERO,
CH UP/DOWN, VOL UP/DOWN
RESET COUNTER, TAPE POSITION
3
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to "VIDEO."
Notes
• Not all functions listed may be controllable.
• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection.
I I I I I With a Cable Box (VCR
TV Brand Code Numbers
Panasonic ................................... 01, 02
Sony .................................................. 08
ANT
AUDIO
IN FROM ANT.
Quasar ......................................... 01, 02
Toshiba .............................................. 09
R
or
RCA ................................................... 03
Sanyo ................................................ 10
CATV
L
VIDEO
GE ...................................................... 03
Fisher ................................................. 10
Sharp ................................................. 06
Hitachi ............................................... 12
IN 1
OUT
Important Notes
• Some manufacturers use several codes for one brand. If the first code entered fails, try the next one listed.
• Some TV brands require you to turn on the power manually.
I I I I I Connect With Two Cable Boxes
CABLE BOX
IN
OUT
ANT
or
2-Way Splitter
CATV
OUT 1
OUT 2
- 2 -
V4524S-K Advanced-2 (031219) new form.p65
3
LSQT0816A (E) Advanced OP - Back
MTS Broadcast
Connection
Make the Audio/Video Connection as shown on page 3.
• You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.
TV
ANTENNA
VCR
R
L
IN FROM ANT.
TV
VIDEO IN
VHF/UHF
AUDIO IN
R
VHF/UHF
L
OUT TO TV
Receivable Broadcast Types
The following are possible audio broadcast types and on-screen displays.
The signal being received is indicated with a " " mark while the selected audio mode is indicated
with an arrow.
To display the broadcast signal being received,
➛ ➛ ➛ ➛ ➛ press DISPLAY*.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main language) and
Secondary Audio Program (sub language) broadcasts are being
received simultaneously. Select STEREO or SAP audio mode.
MTS Stereo broadcast
Cable Box)
You Can
You Cannot
Multi-channel Television Sound Stereo broadcast.
TV
• record scrambled
• view any
Select STEREO audio mode.
channels.
(including
• If stereo broadcast is weak and display flickers, select MONO
IN
OUT
scrambled)
audio mode for possible better results.
R
CABLE BOX
channel.
AUDIO
L
VHF/UHF
OUT TO TV
IN
OUT
VIDEO
• use VCR Remote
VHF/UHF
Control to select
channels without
VCR
SAP broadcast
using Multi-brand
control feature.
Secondary Audio Program (sub language) broadcast.
Select SAP audio mode for the sub language.
You Can
You Cannot
VCR
• record and view
• view a channel
other than the
MONO broadcast
both scrambled
AUDIO
IN FROM ANT.
one selected for
R
and unscrambled
Normal monaural sound broadcast.
any type of
channels if
L
VHF/UHF
recording.
additional
VIDEO
OUT TO TV
equipment is
• do a Timer
IN 1
OUT
TV
added.
recording of a
This connection
A/B Switch
IN
OUT
channel unless
requires: two
R
you select it at
CABLE BOX
AUDIO
converter boxes,
L
the cable box.
an A/B switch, and
IN
OUT
IN 1
IN 2
VIDEO
a 2-way splitter.
VHF/UHF
Equipped with
®
-TV Noise Reduction for true
MTS reproduction.
®
-TV Noise Reduction is
required for good stereo separation and audio
fidelity.
®
is a registered trademark, and is
licensed by
®
Technology Licensing.
- 3 -
VHS Hi-Fi Stereo System
Audio Mode for Recording
1
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
2
Press SAP/ Hi-Fi repeatedly
to select desired mode.
STEREO
SAP
• Refer to "Receivable
MONO
Broadcast Types" on page 4.
Stereo Amplifier
AUDIO OUT
• Arrow indicates selection.
R
R
L
3
Make a recording.
AUDIO IN
R
See p. 5 of "Basic Operations" Instruction book.
L
OUT TO TV
Audio Mode for Playback
1
Start playback.
See p. 5 of "Basic Operations" Instruction book.
2
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
3
Press SAP/ Hi-Fi repeatedly
to select desired mode.
H I F I : L / R
H I F I : L
• Select "HIFI(L/R)" or "HIFI(L)"
H I F I : R
NORMAL
or "HIFI(R)" to listen to stereo
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
recordings in stereo sound.
STEREO
SP
Select "NORMAL" for
SAP
MONO
monaural sound.
• Arrow indicates
selection.
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
STEREO
SP
SAP
MONO
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.
Standard stereo tapes will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a
stereo TV or an external stereo amp and speakers. (See page 4.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
STEREO
SP
• Hi-Fi and normal audio playback volume level may differ.
SAP
MONO
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
STEREO
SP
SAP
MONO
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 4 -
- 5 -
2003/12/22, 15:20
Tape Operation
Tape Operation
Search System
Repeat Play
Tape Select
For each recording, an invisible index mark is
Set to playback a recording over and over.
Select your tape length so the tape position and
placed on the tape.
amount of tape remaining are properly displayed.
1
A program index and information are also
(See "Tape Position and Tape Status Display"
Press ACTION to display menu.
included for timer recordings.
section below.)
These marks are used to access or scan
2
Press
to select
MENU
1
SET UP VCR
Press ACTION to display menu.
recordings.
SET UP CLOCK
"SET UP VCR,"
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
and press .
VCR'S OUTPUT CH: 3
2
Index Search
MENU
SET UP VCR
SELECT :
SET:
SET UP CLOCK
EXIT
: ACTION
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
1
Press SEARCH* to display
INDEX SEARCH
VCR'S OUTPUT CH: 3
SEARCH in Stop or Play
ENTER INDEX NUMBER :1
3
Press
to select
SET UP VCR
SELECT :
SET:
USING 1- 9 KEYS
mode, and then press
REPEAT PLAY
: OFF
EXIT
: ACTION
AUTO SHUT-OFF
: OFF
"REPEAT PLAY,"
FORWARD SEARCH :FF
NUMBER keys to select
FRONT DISPLAY
: ON
REVERSE SEARCH :REW
and press
to set
AUTO VCR/TV
: ON
recording number.
TAPE SELECT
: T-120
"ON" or "OFF."
3
EXIT
:SEARCH
SET UP VCR
• To calculate number,
REPEAT PLAY
: OFF
SELECT :
SET:
ON :Play repeats at tape end
AUTO SHUT-OFF
: OFF
EXIT
: ACT I ON
see below.
FRONT DISPLAY
: ON
or if unrecorded portion
AUTO VCR/TV
: ON
TAPE SELECT
: T-120
Press FF or REW to start
over 30 sec. is detected.
search.
SELECT :
SET:
EXIT
: ACT I ON
4
Press ACTION
to return to normal screen.
2
Play begins at search end.
• Select "T-120" for tapes 120 minutes or
INDEX SEARCH
To search forward or back 1
less, "T-160" if 140 or 160 minutes, and
index, press FF or REW
"T-180" if 180 minutes.
while screen left is displayed
FORWARD SEARCH :FF
(10 sec.).
4
REVERSE SEARCH :REW
Press ACTION
• To cancel, press PLAY or
to return to normal screen.
STOP.
Zero Search
To quickly return to a specified tape location.
1
Tape Position and Tape Status
Press DISPLAY during play
To Calculate Index Number
Display
to display Counter.
Example 1:
To find out the present tape position and amount
To go to rec. 2 from rec. 4, enter 3 and press REW.
2
Press COUNTER RESET
of tape remaining.
PLAY
1 2 : 0 0AM
0 : 0 0 : 0 0
on remote at desired position
SP
to reset to "0:00:00".
Tape position is displayed incorrectly in the
following cases:
1
2
3
4
5
6
7
• If VHS-C type cassettes, tapes under 30
minutes, tapes over 180 minutes, or
incompatible tapes are used.
• If the correct tape length is not selected.
Example 2:
3
Continue to record, playback, etc.
(See "Tape Select" section above.)
To go to rec. 6 from rec. 2, enter 4 and press FF.
1
4
Press STOP.
Press TAPE POSITION
to detect tape position.
1
2
3
4
5
6
7
5
Press CM/ZERO in
REW
1 2 : 3 0AM
CH 02
DETECTING TAPE POSITION
0 : 30 : 30
SP
Stop mode to start
ZERO SEARCH.
NOTE:
indicates start points of each recording.
• Unit will go into FF or REW
mode and stop at the last
point the Counter was set
Note
to 0:00:00.
SP
• If Index Search is started very close to an
R 120 M I N.
index mark, that index mark may not be
STOP
1 2 : 3 1AM
CH 02
0 : 0 0 : 0 0
counted in the search.
BEG I N
END
SP
2
Press TAPE POSITION (or wait 5 seconds)
to return to normal screen.
*Important: If a remote control button does not work when pressed,
- 6 -
Commercial Skip
VCR fast forwards (skips) over 1, 2, or 3 minutes
of recorded tape as desired.
1
Press CM/ZERO in Play mode.
• Press CM/ZERO repeatedly to change skip
time as shown below.
Press
to select
PLAY
"SET UP VCR,"
and press .
1st Press
1 min Skip
2nd Press
2 min Skip
Press
to select
"TAPE SELECT," and
3rd Press
3 min Skip
press
to set "T-120,"
"T-160" or "T-180."
• No indication appears.
T-120
T-160
T-180
• "DETECTING TAPE
POSITION" only
appears the first time a
cassette is inserted
and it takes several
seconds for correct
indication to appear.
• The present tape
position indication and
amount of tape
remaining (according to
tape speed) are
displayed.
Tape remaining time
display may not be
precise.
press the VCR button on the remote and try the button again.
- 7 -
Advertisement
Table of Contents
