Table of Contents
Advertisement
Available languages
Available languages
Copying Your Tapes (Dubbing)
Connection
(Rear connection shown.)
VCR
(HiFi)
AUDIO OUT
Connect VIDEO OUT jack on Playing VCR to VIDEO IN jack on Recording VCR.
1
To monitor the dubbing, also connect a TV as shown.
2
Connect AUDIO L/R OUT jacks on Playing VCR to AUDIO L/R IN jacks on Recording VCR.
In place of a Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit's Audio/Video outputs to the Recording VCR.
Playing (Source) VCR
1
Insert pre-recorded tape.
2
3
Press PLAY, then PAUSE/SLOW
immediately to enter PLAY/PAUSE mode.
4
Press PLAY to start dubbing.
Playing VCR starts playback.
5
Press STOP to stop dubbing.
To Monitor Dubbing on Your TV
1
Turn your TV on and tune to the Recording
VCR channel (CH3 or CH4).
2
Set the VCR/ TV Selector on the Recording
VCR to "VCR."
Note
• Dubbing tapes protected with Copy
Guard will have poor quality results.
Montréal: 3075 Louis A. Amos, Lachine, Québec H8T 1C4 (514) 633-8684
Toronto: 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-8447
Calgary: 6835 8th Street N.E., Calgary, Alberta T2E 7H7 (403) 295-3955
Vancouver: 12111 Riverside Way, Richmond, BC V6W 1K8 (604) 278-4211
Panasonic Canada Inc.
5770 Ambler Drive,
K
Caution :
Unauthorized exchanging and/or copying of copyrighted recordings may be
Mississauga, Ontario L4W 2T3
copyright infringement.
(905) 624-5010
www.panasonic.ca
Printed in Indonesia
LSQT0816 A
S1203-0
- 8 -
V4524S-K Advanced-1 (031219) new form.p65
1
LSQT0816A (E) Advanced OP - Front
Special VCR Features
Auto Shut-Off Feature
The power shuts off at a preset time.
1
Press ACTION to display MENU.
VCR
IN FROM ANT.
TV
2
Press
to select
MENU
(HiFi)
SET UP VCR
SET UP CLOCK
"SET UP VCR,"
OUT TO TV
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
and press .
VCR'S OUTPUT CH: 3
R
R
R
L
SELECT :
SET:
L
EXIT
: ACTION
R
3
Press
to select
L
SET UP VCR
REPEAT PLAY
: OFF
"AUTO SHUT-OFF."
AUDIO IN
AUTO SHUT-OFF
: OFF
FRONT DISPLAY
: ON
AUTO VCR/TV
: ON
Press
repeatedly to
VIDEO OUT
TAPE SELECT
: T-120
change shutoff time as
VIDEO IN
VHF/UHF
SELECT :
SET:
shown below.
EXIT
: ACT I ON
Front of VCR
VIDEO IN 2
L-AUDIO IN2-R
4
Press ACTION
to return to normal screen.
(Front Audio L/R Video IN jacks
are also provided)
• The shut-off countdown will not
Note
function during Play or Record.
VCR/TV Selection Feature
The VCR/TV selection can be set to auto or
manual.
1
Press ACTION to display MENU.
Recording (Editing) VCR
2
MENU
Press
to select
SET UP VCR
"SET UP VCR,"
SET UP CLOCK
SET UP CHANNEL
Insert blank tape with record tab.
IDIOMA/LANGUE : ENGLISH
and press .
VCR'S OUTPUT CH: 3
SELECT :
SET:
EXIT
: ACTION
Press INPUT* to set VCR Input mode to LINE1
for Video Input (Rear) or to LINE2 for Video Input
3
Press
to select
SET UP VCR
REPEAT PLAY
: OFF
"AUTO VCR/TV,"
(Front). (See "Selecting the Input Mode" below.)
AUTO SHUT-OFF
: OFF
FRONT DISPLAY
: ON
and press
to set
AUTO VCR/TV
: ON
"ON" or "OFF."
TAPE SELECT
: T-120
Press REC, then PAUSE/SLOW immediately to
SELECT :
SET:
EXIT
: ACT I ON
enter REC/PAUSE mode.
• OFF(Manual): You select "VCR" or "TV" mode
The operation of steps 4 and 5 must be done on both playing
using the VCR/TV button on the
unit or remote.
and recording VCRs at the same time.
• ON(Auto):
"VCR" mode is automatically set
Press PAUSE/SLOW to start dubbing.
when VCR is turned on, or in Play
mode.
Recording VCR starts recording.
4
Press ACTION
to return to normal screen.
Press STOP to stop dubbing.
Note
• For more on VCR/TV selection, see "Record one
Selecting the Input Mode
station, watch another" and "Select channels on
Method 1:
VCR" sections (p. 5 of Basic Operations book).
Press INPUT repeatedly.
Channel Number ↔ ↔ ↔ ↔ ↔ LINE1 ↔ ↔ ↔ ↔ ↔ LINE2
Method 2:
Press CH
/
.
VCR Lock Feature
Display will change as below.
When set to ON, all operations except for timer
1
2
3
record and tape eject are prohibited. Useful for
households with small children.
(CABLE)
(TV)
LINE2
LINE1
125
or
69
To turn on, hold down REC
on the VCR in Stop mode with
• "L1" or "L2" lights on Multi-Function Display
BLOQUEO DEL VCR:INACTIVO
BLOQUEO DEL VCR:INACT
no tape inserted for 7 sec.
(about 4 sec.) when LINE1 or LINE2 is
(Please ignore the NO
selected.
CASSETTE warning.)
• LINE1: For rear audio/video connection.
LINE2: For front audio/video connection.
To turn off, repeat above.
VCR LOCK OFF
• VCR Lock cancels in 24 hours.
- 9 -
On-Screen Displays (OSD)
Weak Signal Display ON/OFF Feature
On-Screen Displays (OSD)
When set to "ON," picture is displayed regardless
Function & Channel Displays
Blank Tape/
of signal strength.
No Video Signal Indications
When a function button is
1
CH 0 8
Press ACTION to display MENU.
When blank tape is detected during play, or
pressed, e.g. PLAY, or you
change channels,
the current channel has no signal (with Weak
2
Press
to select
MENU
SET UP VCR
Signal Display feature (p. 10) set to OFF), the
a 5 second display
SET UP CLOCK
"SET UP CHANNEL,"
SET UP CHANNEL
appears.
TV screen will turn solid blue.
IDIOMA/LANGUE : ENGLISH
and press .
VCR'S OUTPUT CH: 3
SELECT :
SET:
EXIT
: ACTION
VCR Status & Clock Displays
3
Press
to select
SET UP CHANNEL
To display or remove
WEAK SIGNAL
ANTENNA : CABLE
AUTO SET
DISPLAY, and press
overlay at right,
Current Time
WEAK S I GNAL D I SPLAY:OFF
Function Status
to set "ON" or "OFF."
➛ press DISPLAY*.
SELECT :
SET:
Rec Time Remaining
REC
1 2 : 0 0AM
EXIT
: ACT I ON
0 : 25
(OTR mode only.
STEREO
SAP
• ON : Picture is displayed even if signal
See p. 5 of Basic
MONO
is very weak but quality may be poor.
Operations book.)
OFF : Screen turns solid blue when signal
is weak or non-existent.
Broadcast Audio
• Selecting "ON" has no effect on connected
Being Received
equipment with blue back feature.
4
Press ACTION
to return to normal screen.
These displays will alert you to a missed operation or
Warning and Instruction Displays
Multi Function Display
provide further instructions.
(Front Display) ON/OFF Feature
OSD
Caution
Multi Function Display (Front Display) can be
set to ON/OFF.
1
If you attempt to set or review a Timer
Press ACTION to display MENU.
PLEASE SET CLOCK BY
PRESSING ACTION KEY
Recording and the Clock is not set...
2
Press
to select
MENU
SET UP VCR
SET UP CLOCK
"SET UP VCR,"
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
and press .
VCR'S OUTPUT CH: 3
SELECT :
SET:
EXIT
: ACTION
TURN VCR OFF
After a Timer Program has been set...
FOR TIMER RECORDING
3
Press
to select
SET UP VCR
REPEAT PLAY
: OFF
"FRONT DISPLAY,"
AUTO SHUT-OFF
: OFF
FRONT DISPLAY
: ON
and press
to set
AUTO VCR/TV
: ON
TAPE SELECT
: T-120
"ON" or "OFF."
If you press REC on the remote
SELECT :
SET:
EXIT
: ACT I ON
CHECK CASSETTE
control or VCR, and a cassette is
RECORD TAB
• ON : When set to "ON,"
inserted with no record tab...
Multi Function Display is displayed
in Standby (OFF) mode.
OFF : When set to "OFF,"
If you press PLAY, FF, REW, or REC on
Multi Function Display is not
NO CASSETTE
the remote control or VCR without a
displayed in Standby (OFF) mode.
cassette inserted...
If a Timer Program is set,
Multi Function Display is displayed.
4
Press ACTION
to return to normal screen.
TO CANCEL TIMER REC
If you press POWER or STOP during
PRESS POWER THEN
a Timer Recording...
STOP KEY
(visible in VCR mode only)
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT HEAD
If head cleaning becomes necessary
CLEANING CASSETTE
while playing back a tape...
OR REFER TO MANUAL
REC
END
:PLAY
Multi Function Display
(Front Display)
If you press a function button other
VCR LOCK ACTIVATED
than STOP/EJECT or POWER while
the VCR is in VCR Lock mode...
*Important:
If a remote control button does not work
when pressed, press the VCR button on
the remote and try the button again.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 10 -
- 11 -
2003/12/22, 15:20
Before Requesting Service
Check the following points once again if you are having trouble with your VCR.
(BO : refers to "Basic Operations" Instruction book.)
(AO : refers to "Advanced Operations" Instruction book.)
Power
Correction
No power...
• Completely insert Power Plug into an AC outlet.
• Press POWER button on.
• Make sure power source is active.
Recording & Playback
Correction
TV program cannot be recorded...
• Check connections between VCR, external antenna, and
TV.
• Check connections selection. (BO p. 4, AO p. 3)
• Make sure your antenna system (CABLE or TV) is correctly
set. (Channels [BO p. 11])
Channel
• Make sure cassette record tab is intact. (BO p. 3)
CH 02
Timer recording cannot be
• Confirm that clock is set to current time and date.
-0 : 1 2 : 3 4
Counter
SP
performed...
• Make sure Cable/DSS box (if used) is left on and tuned to
channel to be recorded.
• Set recording start/stop times correctly. (BO p. 6, 7)
• Make sure VCR POWER button is pressed off. (BO p. 6, 7)
• Timer recording may not be performed or continued if a
Tape Speed
power interruption occurs before or during a Timer
(See p. 3 of Basic
Recording, even after power is restored.
Operations book.)
There is no playback picture, or the
• Select channel 3 or 4 on TV to match VCR output channel
playback picture is noisy or contains
(3 or 4) (BO p. 4) or select LINE.
streaks...
• Set VCR/TV selector to "VCR."
• Adjust TRACKING control in either direction. (BO p. 3)
• Try Head Cleaning. (BO p. 3)
Special effects playback picture
• Set TV's Vertical Hold Control to MANUAL, then adjust.
may contain some vertical jitter
when using a TV with an Automatic
Vertical Hold Control...
Page
VCR cannot be controlled...
• Make sure VCR power is on.
• Check Remote batteries.
• Make sure VCR LOCK is set to off. (AO p. 10)
See pages 6, 7 of
• Make sure Timer Record is not in progress.
Basic Operations
book
Remote Control
Correction
VCR cannot be remote controlled...
• Make sure VCR power is on.
• Make sure Remote is in VCR mode.
• Aim Remote Control directly at remote sensor on VCR.
See pages 6, 7 of
(BO p. 10)
Basic Operations
• Avoid any object blocking signal path.
book
• Check Remote batteries. (BO p. 3)
• Make sure VCR LOCK is set to off. (AO p. 10)
• Exposing VCR remote sensor to direct fluorescent or
outdoor light may cause signal interference.
See page 3 of Basic
ACTION and PROG buttons do not
• Check connections between VCR, external antenna, and
Operations book
respond...
TV.
• Press VCR button for VCR mode. (AO p. 2)
• Check Remote batteries. (BO p. 3)
Miscellaneous
Correction
See page 5 of Basic
Operations book
Programs cannot be viewed on TV...
• Make sure TV power is on.
• Make sure TV is tuned to VCR's output channel (3 or 4).
• Check connections between VCR, external antenna, and
TV.
• Set VCR/TV selector to "TV." (BO p. 5, AO p.10)
See pages 6, 7 of
• Make sure proper signal source is selected.
Basic Operations
Video cassette cannot be inserted...
• Insert the cassette with window side up; record tab facing
book
you.
• Check if a tape is already in the unit.
Video cassette cannot be removed...
• Confirm Power Plug is fully inserted into an AC outlet.
Video cassette ejects when a
• Make sure cassette record tab is intact. (BO p. 3)
See page 3 of Basic
recording is started or the power is
Operations book
turned off for timer recording...
In Stop mode, the motor
• To enable Quick play mechanism, the cylinder will rotate for
(CYLINDER) continues to rotate...
about 5 minutes. This reduces response time from Stop to
Play mode and from Play to Rewind Search mode.
See page 10
- 12 -
Video Cassette Recorder
Operating Instructions
(Advanced Operations)
For Basic operations, see the separate
"Basic Operations" instruction book.
PV-V4524S-K
Model No.
Table of Contents
Multi-Brand Control Feature ............................................ 2
Advanced Connections (Cable/DSS) .............................. 3
MTS Broadcast ................................................................ 4
VHS Hi-Fi Stereo System ................................................ 5
Tape Operation ............................................................ 6, 7
Copying Your Tapes (Dubbing) ...................................... 9
Special VCR Features .................................................. 10
On-Screen Displays (OSD) ........................................... 11
Before Requesting Service ........................................... 12
As an
E
NERGY
S
TAR
®
Participant, Panasonic has determined
E
S
®
that this product or product model meets the
NERGY
TAR
guidelines for energy efficiency.
Please read these instructions carefully before attempting to
connect, operate or adjust this product. Please save this manual.
LSQT0816 A
For assistance, please call : 1-800-561-5505 or visit us at www.panasonic.ca
Advertisement
Table of Contents
