Panasonic WV-CM2000 Operating Instruction page 5

1. Power Switch (POWER ON/OFF)
This is a push-push type switch which turns the power
of the monitor on and off.
Press once and the switch remains down (
ing on the power of monitor.
Press again, the switch comes up ( ) for turning off
the power of the monitor.
2. Stand-by On/Off Switch (STAND BY ON/OFF)
This is a push-push type switch which turns on/off this
switch.
Press once and the switch remains down (
ing on this switch.
Press again, the switch comes up ( ) for turning off
this switch.
When selecting the Standby On/Off mode by using the
external signal, set this switch to the ON position.
3. AFC time Selection Switch (AFC, LONG/SHORT)
This is a push-push type switch which selects the AFC
time. Press once, then the switch remains down (
for selecting the LONG position.
Press again, then the switch comes up ( ) for select-
ing the SHORT position.
Normally (standard video signal), set this switch to the
SHORT position.
When the video signal is jittery, set this switch to the
LONG position.
4. 3.58 MHz Trap Filter On/Off Switch
(3.58 TRAP, ON/OFF)
This is a push-push type switch which turns on/off the
3.58 MHz Trap Filter.
Press once, then the switch remains down (
tuning off the 3.58 MHz Trap Filter.
Press again, then the switch remains down ( ) for
turning on the 3.58 MHz Trap Filter function.
Note: When decreasing the colour dots noise on the
monitor screen, turn on this switch.
5. Picture Selection Switch (PICTURE NARROW/
WIDE)
NARROW: Select this position when the video source
is come from the high resolution camera or the
like.
WIDE: Select this position when the video source is
come from the low resolution VTR.
6. Vertical Hold Control (V-HOLD)
This control is used to adjust the picture in vertically.
POWER
ON
OFF
7. Horizontal Hold Control (H-HOLD)
This control is used to lock the picture in horizontally.
) for turn-
) for turn-
)
) for
VIDEO Y/C
1 2 3 4
PAL
NTSC
(3.58)
M.NTSC
(4.43)
INPUT SELECT
-3-
8. Tint Control (TINT)
Turn this control clockwise for purplish colour of the
picture and turn this counterclockwise for greenish
colour of the picture.
9. Tint Subcontrol
10. Colour Control (COLOUR)
Turn this control clockwise to increase the picture
colour and turn this control counterclockwise to
decrease the picture colour.
11. Colour Subcontrol
12. Bright Control (BRIGHT)
Turn this control clockwise to increase the picture
brightness and turn this control counterclockwise to
decrease the picture brightness.
13. Bright Subcontrol
14. Contrast Control (CONTRAST)
Turn this control clockwise to increase the picture con-
trast and turn this control counterclockwise to
decrease the picture contrast.
15. Contrast Subcontrol
16. Picture Adjustment (PICTURE)
Turn this control clockwise for sharp picture and turn
this control counterclockwise for soft picture.
17. Audio Volume (AUDIO, MIN/MAX)
Turn this volume clockwise to increase the audio level
and turn this volume counterclockwise to decrease the
audio level.
18. Power Indicator/Broadcast System Indicator
(PAL, NTSC, M-NTSC)
When turning on the power of this monitor without any
input signals, PAL LED indicator lights in red.
The NTSC LED indicator lights in green with the NTSC
input signal.
The M-NTSC LED indicator light in orange with the M-
NTSC input signal.
These indicators are switched by the difference in the
broadcasting system connected to this monitor.
In the Stand-by mode, PAL and NTSC LEDs light
together.
19. Input Signal Selection Switches (INPUT 1/2/3/4)
By pressing the desired switch, both Video (S-Video)
and Audio input signals are selected.
Note : The video and audio input signal selected once
will be kept even if the power of this monitor is
turned off.
20. Focus Control (FOCUS)