1. Manuals
  2. Brands
  3. LISTAESCAN Manuals
  4. Desktop
  5. ARLINK 8000
  6. Instructions for assembly

LISTAESCAN ARLINK 8000 Instructions For Assembly

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Arlink 8000 Workstation
Making Workspace Work® is a trademark of Lista International Corporation.
Creation Date
Feb/01/06
This manual is proprietary information of Lista International Corporation. Unauthorized
reproduction of any portion of the manual is prohibited without consent of Lista
International Corporation. The material in this manual is for informational purposes
only. It is subject to change without notice. Lista International Corporation assumes
no responsibility for any typographical errors contained in the manual.
© 2006 by Lista International Corporation, all rights reserved.
106 Lowland Street
Holliston, MA 01746-2094
E-mail: sales@ listaintl.com
All rights reserved.
For questions or technical support, call 1-800-722-3020
ISO 9001 Certified
Instructions for Assembly
Introduction
Basic Frame Assembly
Worksurface Assembly
Drawer and Light Fixture Assembly
Micro Slot Accessory Mounting
Macro Slot Accessory Mounting
Worksurface Grounding Instructions
Wrist Strap Receptacle Grounding & Cleaning
Document Number
AS80026
Rev
Description
B
Arlink 8000 Workstation

Advertisement

Table of Contents
loading

Related Manuals for LISTAESCAN ARLINK 8000

Summary of Contents for LISTAESCAN ARLINK 8000

  • Page 1 Arlink 8000 Workstation Instructions for Assembly Introduction Basic Frame Assembly Worksurface Assembly Drawer and Light Fixture Assembly Micro Slot Accessory Mounting Macro Slot Accessory Mounting Worksurface Grounding Instructions Wrist Strap Receptacle Grounding & Cleaning Making Workspace Work® is a trademark of Lista International Corporation.

  • Page 2: Table Of Contents

    Table of Contents Arlink 8000 Introduction ....3 Tool Trolley Track ......7 Basic Frame........ 4 Micro Slot Accessories....7 Single Station......4 Modesty Panel ......7 In-Line Station......4 Powerbeam.........7 Alignment........4 Parts Bin Rail ......7 Standard Worksurface ....5 Part Bin Rail Accessories....7 Round or Straight Back Corner...

  • Page 3: Arlink 8000 Introduction

    In order to appreciate this unique concept, we suggest you spend a 1. Décor Trim few minutes studying the instructions before starting assembly of 2. Vertical support column your Arlink 8000 Workstation. 3. Light fixture support bracket Should you have any difficulty during assembly or have further 4.

  • Page 4: Basic Frame

    Basic Frame Assembly Install all leveling glides before starting assembly. The column glide should only be threaded half way into the column, while the outrigger glides should be threaded into the outriggers their full length. Install outriggers by inserting the tongues of the outrigger into the center slot or Macro slot of the column. Secure with clevis pins through the tongues of the outrigger, then insert the retainer through the hole in the clevis pin.

  • Page 5: Standard Worksurface

    Worksurface Assembly Place the worksurface face down on a smooth surface to prevent damage. Place the worksurface brackets and support beams in their proper locations as shown below. Install the four 1/4-20 x 1” machines screws provided and tighten once all are in place. NOTE: If you have drawers on your system now is the time to hang them.

  • Page 6: Drawer, Tote Box & Cpu Holder

    Drawer, Tote Box & CPU Holder Mounting Drawers and Tote Boxes are mounted using two steel strip drawer hangers which slide inside the worksurface support beams. Drawers should be installed before the worksurface assembly is mounted on the system. If the worksurface assembly is already in place, it should be removed for drawer installation.

  • Page 7: Tool Trolley Track

    Tool Trolley Track Power Beam Mounts to light brackets, with or without light. Can Power Beams are installed by hooking the brackets be mounted in front of or behind light. Install one of into the micro slots. Hook the cord end in first then the screws and square nuts provided.

  • Page 8: Airbeam

    Air Beam Air beams are provided with two or three receptacles for 1/4” NPT quick connects. Any receptacles not used with quick connects must be plugged. Each end of the air beam is equipped with a quick connect fitting for 1/4” tube. This allows air beams to be connected in line.

  • Page 9: Grounding Static Protected Worksurfaces

    Grounding Static Protected Worksurfaces In order to prevent a possible electrical shock hazard to personnel, the static protected laminate should not be directly connected to ground at any point. Recommended grounding procedures suggest installing an in-line 1 MEG OHM current limiting resistor between the static protected laminate and the ground.

  • Page 10: Sc12 Dual Wrist Strap Receptacle

    SC12 Dual Wrist Strap Receptacle This should be mounted onto the worksurface support beam much like the drawer assembly. Loosely fasten the hanger to the wrist strap receptacle. Slide it into the worksurface support beam and tighten hardware. Attach ground lead to brass worksurface ground bolt.
  • Page 11 Document Number: AS80026 Print Date: May, 2006 This manual is proprietary information of Lista International Corporation. Unauthorized repro- duction of any portion of this manual is prohibited without written consent of Lista International Corporation. The material in this manual is for informational purposes only. It is subject to change without notice.

Table of Contents