Table of Contents
Advertisement
Quick Links
AWC10HP
Air Compressor
Direct drive, oil lubricated, ducted air cooled, portable compressor
A small, direct drive, oil lubricated, ducted air cooled, portable compressor. Great in the
workshop or around the home for low volume air tools such as air staplers and nailers,
air brush painting, occasional tyre inflation etc. Quite a robust little unit with a cast iron
Axminster Tool Centre,
Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PH
www.axminster.co.uk
cylinder for long life. Twin pressure gauges
monitor receiver and output pressures.
Supplied with four rubber feet, top grab
handle for easy mobility, output pressure
control valve and a 1/4" BSP female quick
release fitting.
Advertisement
Table of Contents
Related Manuals for Axminster AWC10HP
Summary of Contents for Axminster AWC10HP
-
Page 1: Air Compressor
Supplied with four rubber feet, top grab handle for easy mobility, output pressure control valve and a 1/4” BSP female quick release fitting. Axminster Tool Centre, Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PH www.axminster.co.uk... -
Page 2: Table Of Contents
Index of Contents Page No Index of Contents......................................02 Declaration of Conformity..................................... 02 What’s Included......................................... 03 Safety Precautions......................................03 Specifications (AWC10HP Air Compressor)............................. 04 Assembly Instructions....................................04-05 Illustration and Parts Description of Air Compressor......................05-06-07 Operating Instructions....................................08 Maintenance........................................09 Parts Breakdown....................................... 10 Parts List.......................................... -
Page 3: What's Included
10. Do not adjust the tank pressure switch without 2. Never leave inflammable objects or materials near reference to Axminster Power Tool Service to the compressor. Department. 3. Always check oil level before using the 11. -
Page 4: Specifications (Awc10Hp Air Compressor)
Report any problems to oil filler plug (See fig 2) and fill with a good quality Axminster Power Tool Centre’s Customer Services compressor oil, (see our catalogue) until the level is in Department. Fit the rubber feet, air filter and quick line with the circle marked on the oil level indicator. -
Page 5: Illustration And Parts Description Of Air Compressor
Assembly Instructions Fitting the quick release coupling Wrap some PTFE tape (A) around the outlet thread and screw on the 1/4" BSP female coupling (B) and, lightly tighten with a spanner. (DO NOT OVERTIGHTEN) Illustration and Parts Description of Air Compressor Oil drain plug Oil level indicator Tank pressure gauge (A) &... - Page 6 Illustration and Parts Description of Air Compressor Fig 1 Motor cover Handle Cylinder On/Off switch Pressure switch Pressure adjuster Outlet pressure gauge Tank pressure Crankcase gauge Pressure relief valve Wheel Tank Rubber foot Water drain valve...
- Page 7 Illustration and Parts Description of Air Compressor Motor vents Filter Pressure adjuster Air inlet filter Fig 2 Quick release coupling Oil filler plug Oil level indicator and drain plug...
-
Page 8: Operating Instructions
Operating Instructions The outlet air pressure can be regulated by rotating the drops below a pre-set level. The cut-in and cut-out regulator knob clockwise to increase the pressure and pressures are factory set and should not need to be anticlockwise to reduce it. Do not leave the regulator altered. -
Page 9: Maintenance
Maintenance Daily: filler plug, place a suitable container under the drain plug and drain the oil right out. Replace drain plug and Drain water from tank. (See fig 5) refill to the level mark on the sight glass (See figs 6-8). Weekly: Yearly: Check oil level and top-up if necessary. -
Page 10: Parts Breakdown
Parts Breakdown... -
Page 11: Parts List
Parts List Wiring Diagram... -
Page 12: Trouble Shooting
Carefully clean all sealing surfaces before re-assembling The compressor Crank bearing failure Stop the compressor and contact Axminster does not reach the Tool Centre set pressure and overheats The compressor is Pressure switch failure Stop the compressor quickly.
Need help?
Do you have a question about the AWC10HP and is the answer not in the manual?
Questions and answers