Download  Print this page

KitchenAid KDRP407HSS0 Installation Instructions Manual page 7

30" commercial style dual fuel range with self-cleaning thermal/convection oven
Hide thumbs

Advertisement

3 front screws
(4 rear screws required
but not shown)
attachingthe
backguard
attaching the island
trim
center h01e
not used
[] Attach the backguard
or island trim
as required for your installation.
Attachment
screws are in the literature
package.
[] Slide range completely
back so
anti-tip bracket is over rear brace of
range.
regilat0r
use pipe-j0int
compound
flexible
connector
1/2 flare/
union adapter
manual gas
shutoff valve
/
1/2"to 3/4"gas
pipe
a 1/2" male pipe thread is neededfor connection
to pressure regulator female pipe threads
[] Make gas connection.
Assemble
flexible connector
from gas supply pipe to
pressure
regulator
located in the middle
front of the range. Apply pipe-joint
compound
made for use with L.R gas to
the smaller thread ends of the flexible
connector
adapters. Attach one adapter
to the pressure
regulator
elbow and the
other adapter to the gas shutoff valve.
Tighten both adapters.
2
[] Open manual shutoff valve in
gas supply line. Wait a few minutes for
gas to move through
the line,
3
[] Use a brush and liquid
detergent
to test all gas connections.
Bubbles around connections
will indicate
a leak. If a leak appears,
shut off gas
valve controls and tighten connections.
Then check connections
again. Clean all
detergent from range.
4
[] Remove cooktop
burner caps,
grates, and simmer
plate from the parts
package. Align the indentation
in the
burner cap with the pins on the burner
base. Burner caps should be level when
properly
positioned.
t5
[] Turn on power supply. "PF"
should appear in the clock display. (Refer
to your Use and Care Guide for
instructions
on using the electronic
control,)
6
[] Check
operation
of cooktop
burners.
Push in and turn
each control knob to the
"LITE" position. The
flame should light within
4 seconds. The first time a burner is
lighted it may take longer than 4 seconds
to light because
of air in the gas line.
7
[] If burners do not light properly,
turn cooktop
control knob to the "OFF"
position. Check that power supply conduit
is properly wired and that circuit breaker
or fuse has not blown. Check that gas
shutoff valves are set to the "OPEN"
position. Repeat step 16. If a burner still
does not light, contact your KitchenAid
dealer or designated
service company.
t
[] Adjust height of top burner
flames. The cooktop LOW burner flame
should be a steady
blue flame
approximately
1/4" (6 mm) high. It can be
adjusted
using the adjustment
screw in
the center of the valve stem. The valve
stem is located directly
underneath
the
control knob. If the LOW flame needs to
be adjusted:
a. Remove the control knob.
b. Hold control
knob stem
controlknob
with a pair of
stem
pliers. Use a
(
small flat-head
screwdriver
to
turn screw
located in the
center of control knob stem until
flame is the proper size.
c. Replace control knob.
d. Test the flame by turning
the control
from "LO" to "HI", checking
flame at
each setting.
GaS COflVerSJOfl$
Gas conversions
(from Natural gas to L.R
gas or from L.R gas to Natural gas) must
be done by a qualified
installer.
L.P. gas conversion:
No attempt shall be made to convert the
range from the gas specified
on the
model/serial
rating plate for use with a
different gas without consulting
the
servicing
gas supplier. An L.R Gas
Conversion
Kit is included in your
literature
package.

Hide quick links:

Advertisement

loading

  Also See for KitchenAid KDRP407HSS0

  Related Manuals for KitchenAid KDRP407HSS0