Advertisement
27" oven
25-3/8
recessed
41"
recessed
height
23" max.
recessed
depth
,26-314"
41-1/4"
cutout
height
1-1/2"
min.
bottom of
cutout to
top of
cab,net
door
"_
27" min.
cabinetwidth
25-1/2"
,._-----
cutout --
width
27" oven
cabinet
----
23-1/4"min.
q[----
cutout depth
23"recessed
oven depth
recessed
oven
Cabinet side view
J
42-7/16"
overall
height
1"top of cutout
tobottomof
upper cabinet
door
f
19-1/4"
bottom of
cutout to
floor
_3_
oven
"_front
41"
recessed
height
23" max.
recessed
depth
30" oven
28-3J8"
29-314"
42-7/16"
overall
height
J
T
41-I/4"
cutout
height
l,
1-1/2" rnin.
bottom of
cutout to
top of
cabinet
door
"9_'--
30" mm.
cabinet
J
2S-1/2"
cutout ---_
width
30" oven
1"top
of cutout
to bottom
of upper
cabinet door
i
19-1/4"
bottom
of cutout
tofloor
_I_
Cabinet filler kits are available from your dealer.
Use a matching color kit if oven is smaller than your
cabinet opening.
27" oven filler height is 7-13/16"
Black
-- 4378950
White
-- 4378951
Almond-
4378952
30" oven filler height is 4-13116"
Black
-- 4378944
White
-- 4378945
Almond-
4378946
Important: Observe all governing codes
and ordinances.
Proper installation is your responsibility.
Have a qualified technician install this oven.
Oven location should be away from strong draft
areas, such as windows, doors and strong
heating vents.
Cabinet opening dimensions that are shown
must be used. Given dimensions provide
minimum clearance.
Recessedinstallation area must provide
complete enclosure around the recessed portion
of the oven.
Electrical ground is required. See "Electrical
requirements."
Electrical supply junction box should be located
3 inches maximum below the support surface
when oven is installed in a wall cabinet. Cutout
for wiring should be in the right rear or left rear
corner. For undercounter installation, it is
recommended that the junction box be located
in the adjacent right or left cabinet. If installing
junction box on rear wall behind oven, junction
box must be recessed and located in the upper
or lower right or left corner of cabinet.
Oven support surface MUST be solid, level and
flush with bottom of cabinet cutout.
Excessive Microwave Energy Exposure
Do Not attempt to operate the microwave
oven with the door open.
Do Not tamper with or defeat the safety
interlocks.
Do Not place objects between the microwave
oven front face and door.
Do Not allow soil or cleaner residue to
accumulate on sealing surface of the
microwave oven door.
Do Not operate the microwave oven if
damaged.
Do Not operate the microwave oven if:
-- door is bent.
-- hinges and latches are broken or loose.
-- door seals, sealing surfaces or glass are
broken.
The microwave oven door must close
properly to provide safe operation.
Have a qualified repair person adjust, repair
and check microwave oven for microwave
leakage after a repair is made.
Do Not use microwave for commercial
purposes. The microwave oven in this unit is
designed for household use only.
Failure to follow these instructions could
result in exposure to excessive microwave
energy.
It is the customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is
adequate and in conformance with National
Electrical Code, ANSI/NFPA 70 -- latest edition*,
and all local codes and ordinances.
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Tool needed:
Phillips screwdriver
Parts supplied:
Page 1
Advertisement
