Advertisement
27=1/2"
recessed
height
Single oven
25=3/8" max.
recessed
width
\
29"max_
overall
height
27=3/4"
min.
cutout
height
27"min,
___
cabinet
width
-
1=1/2" min.
top of cutout
to underside
of ceuntertep
_
25-1/2"
cutout width
5=I/4"
bottom
of
cutout
to f_oer
Single oven
undercounter
{without cooktop
installed above)
T
27=3/4"
min.
cutout
height
1=I/2"
min,
bottom
of
cutout
to
top of
cabinet
door
27" min,
cabinet width
25=1/2"
_---
cutout
---:_
width
1" top of cutout
to bottom
of
upper
cabinet
door
t
32"
bottom
of
cutout
to
floor
Single oven
Double oven
25=3/e"max.
recessed width
49-1/2"
recessed
height
26=314"
j-
61" max,
overs[[
height
r_
J
49-3/4"
min,
cutout
height
1=1/2" min,
bottom of
cutout
to top of
cabinet
door
27" ram.
_---
cabinet
--_
I [
25=1/2"
_---
cutout --_
width
Double
oven
1" top 01 cutout
to bottom
of
upper cabinet
door
14=3/4"
bottom
of cutout
to fleer
cabinet -_
2e=li4"mim
cutout
depth
23"recessed
oven depth
recessed
oven
oven
J'_
front
Cabinet side view
Your safety and the safety of others are
very imp0rtaet.
We have provided many important safety
messages in this manualand on your appliance,
Atwaye read and obey aHsafety messages=
This is the safety alert symbol.
This symboi alerts you to potentiai hazards
that can kiii or hurt you and others.
Ati safety messageswiii foiiow the safety alert
symbol and either the word "DANGER"or
"WARNING".Thesewords mean:
You can be killed or seri0usly injured if you don't
follow instructions.
Ati safety messages wiii teli you what the potential
hazardis, tell you howto reducethe chance of
injury, and teti you what can happen if the
instructions are not followed.
important: Observe ali governing
codes
and ordinances.
Proper installation is your responsibility.
Have a qualified technician install this oven.
Oven location should be away from strong draft
areas, such as windows, doors and strong
heating vents.
Cabinet opening dimensions that are shown
must be used. Given dimensions provide
minimum clearance.
Recessed installation area must provide
complete enclosure around the recessed portion
of the oven.
Electrical ground is required. See "Electrical
requirements."
Electrical supply junction box should be located
3 inches maximum below the support surface
when oven is installed in a wall cabinet. Drill a
1°inch minimum diameter hole in the right rear
or left rear corner of the support surface to pass
the appliance cable through to the junction box.
For undercounter installation, it is recommended
that the junction box be located in the adjacent
right or left cabinet. If installing the junction box
on rear wall behind oven, junction box must be
recessed and located in the upper or lower right
or left corner of cabinet.
Oven support surface MUST be solid, [eve[ and
flush with bottom of cabinet cutout.
it is the customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is
adequate and in conformance with National
Electrical Code, AN81/NFPA 70 E latest edition*,
and nit local codes and ordinances.
Copies
of the standards
listed may be obtained
from:
* National
Fire Protection
Association
Battervmamh
Park
Quincy,
Massachusetts
02269
Tool needed:
S
screwdriver
Parts supplied:
4 screws
(double
oven)
Page 1
Advertisement
