Do you have a question about the MX20 and is the answer not in the manual?
Questions and answers
Michael Swiderski
February 8, 2025
Removal of dough hook. Stuck on mixer. Unit is not a year old.
1 comments:
Mr. Anderson
February 11, 2025
To remove a stuck dough hook from an Avantco MX20 mixer, raise the agitator on the shaft until it clears the lock, then rotate it counter-clockwise and lower it. If the hook remains stuck, ensure all tools are precisely fitted and check for any residue that may be causing resistance. Cleaning and applying a small amount of lubrication may help ease removal.
This answer is automatically generated
Bittu Gill
April 14, 2025
Avantco mx30 I need wiring spec diagram wire color code We remove motor for repair and miss to get together wire connections
Page 1
User Manual User Manual Gear Driven 20 Qt. Commercial Mixer Shifting gears while this unit is Models: MX20 running will void warranty. 08/2012 Please read and keep these instructions. Indoor use only. www.AvantcoEquipment.com...
User Manual PARTS CATALOG OVER Parts Overview ITEM DESCRIPTION Cover ITEM Rear Cover Safety Guard Mixing Device Bowl Lift Wheel Bowl Power Speed NOTE • Do no • Do no Notes: opera • Do not hose down mixer. • Unlpu •...
STANDARD ACCESSORIES OPERATION INSTR User Manual FIGURE 10 Please ensure power supply m Please ensure power supply m NEMA 5015P 110V 110V FOR CHANGING THE SPEED: before changing speed in order t STANDARD ACCESSORIES OPERATION INSTRUCTION FOR CHANGING THE SPEED: Standard Accessories before changing speed in order t FIGURE 10...
User Manual Mixer Capacity Chart Maximum Bowl Product Agitator and Speed Capacity 20 qt Bread and Roll Dough -60 % AR Dough Hook - 1st only 25 lbs. Heavy Bread Dough -55% AR Dough Hook - 1st only 15 lbs. Pizza Dough, Thin -40% AR Dough Hook - 1st only 9 lbs.
User Manual Troubleshooting Trouble Possible Causes Solution The axles can’t work when Poor contact of the electrical Check the Plug operating the machine equipment The mixing bowl is out of position Moving direction is not correct Change Leaks oil Sealing washer is damaged Change Difficult to move the bowl up and down Slideway is rusted...
Page 7
User Manual TRANSMISSION CASE FIGURE 1 ITEM DESCRIPTION SCRIPTION Screw M6*45 Cover r Cover Screw M5*8 ety Guard Cover ng Device Bearing 6201 wl Lift Wheel Screw M6*25 End Cover Body down mixer. Screw M5*8 wet hands while Cover e mixer. Bearing 6003 r from electrical Rear cover...
Page 8
User Manual PLANETARY SHAFT ASSEMBLY FIGURE 2 ITEM DESCRIPTION Baffle Roller Spring Engager Gear Ring Dividing Ring Joint Gear I Bearing Ring Joint Bearing Ring Joint Gear I Ring Bearing 6205 Oil Seal Pd30*45*10 Sleeve Axle Key 6*14 Key 5*35 Key 6*30 Bearing NOTES:...
Page 9
User Manual TRANSMISSION SHAFT FIGURE 3 ITEM DESCRIPTION IPTION Bearing Transmission Axle Key 5*11 Key 5*11 Gear Stop Ring Ring Gear ar I Stop Ring Ring Bearing 6201 Ring NOTES: ar I • At the center in the shaft unit. To the above gear is the gear shaft and gear shaft I (see figure 3-1) 6205...
Page 10
User Manual WORM GEAR SHAFT ASSEMBLY FIGURE 4 ITEM DESCRIPTION Bearing 6201 Gear Axle Key 5*14 Gear Stop Ring Bearing 6201 NOTES: • C-Type stop ring (5) has to be fixed when reassembling. www.AvantcoEquipment.com...
Page 11
User Manual MBLY MOTOR UNIT FIGURE 5 CRIPTION ITEM DESCRIPTION g 6201 Stop Ring Axle Worm Gear Oil Seal Bearing 6203 Ring Key 4*22 g 6201 Axle Rotor Governor ng (5) has to be fixed Governor Plate Bearing 6203 Bearing Cover NOTES: •...
Page 12
User Manual SHIFTING MECHANISM FIGURE 6 ITEM DESCRIPTION Axle Spring Shaft Fork Pin 3*20 Eccentricity Knot Steel Ball Speed Spring Speed Block Screw M5*10 Shaft NOTES: • The speed selector / shifting mecha- nism is designed for simplicity and reli- ablity.
Page 13
User Manual STAND & BOWL LIFT UNIT FIGURE 7 RIPTION ITEM DESCRIPTION Bowl Support Columns Slide Plate Gear Support Seat icity Knot Capacitor Board Capacitor 200uF Spring Nut M10 Block Spring M5*10 Spiral Bowl Lift Support Handwheel Nut M10 tor / shifting mecha- or simplicity and reli- Handle hree mixing speeds.
Page 14
User Manual BOWL LIFT UNIT FIGURE 8 ITEM DESCRIPTION Lifting Bar Cotton Pin 3*30 NutM10 Flat Washer Compression Spring Little Knot Lifting Handle Bracket Flat Washer Flange Knot Screw M6*25 Key 5*20 Bowl Lift Handle www.AvantcoEquipment.com...
User Manual Electrical Diagram ELECTRIC DIAGRAM / Parts Cat Figure 1 T Figure 2 P Figure 3 T Figure 4 W Figure 5 M Figure 6 S Figure 7 S Figure 8 L Figure 8 P Figure 9 S SPECIFICATIONS Type B20GA Operation...
Changing Gears on the Mixers while Unit is Running and Overloading as Determined by an Approved Certified Technician. This warranty does not apply to, and Avantco is not responsible for, any warranty claims made on products sold or used outside of the United States.
Need help?
Do you have a question about the MX20 and is the answer not in the manual?
Questions and answers
Removal of dough hook. Stuck on mixer. Unit is not a year old.
To remove a stuck dough hook from an Avantco MX20 mixer, raise the agitator on the shaft until it clears the lock, then rotate it counter-clockwise and lower it. If the hook remains stuck, ensure all tools are precisely fitted and check for any residue that may be causing resistance. Cleaning and applying a small amount of lubrication may help ease removal.
This answer is automatically generated
Avantco mx30 I need wiring spec diagram wire color code We remove motor for repair and miss to get together wire connections