Receiver & Remote Control Programming - Chamberlain 1280 Owner's Manual

Receiver & Remote Control Programming
NOTICE: To comply with FCC rules, adjustment or modification of this
receiver and/or transmitter are prohibited, except for changing the code
setting or replacing the transmitter battery. THERE ARE NO OTHER
USER SERVICEABLE PARTS.
Your garage door opener receiver and remote control
transmitter have been set at the factory to a matching
code. The door will open when you press the LARGE
remote control push.
Your SECURITY opener will operate with:
• several SECURITY remote controls (with yellow
indicator lights) utilizing up to 8 functions. NOTE:
Open/Close/Stop operation counts as 1 function.
• one Keyless Entry System (with SECURITY logo)
Follow the instructions below to program your opener
to match any additional remotes you may purchase.
See Accessories on page 34.
To Add A Remote Control
1. Press and hold the selected remote control push
button. See Figure 1.
2. Then press and release the "Smart" (learn) button
on the right side panel of the opener, Figure 2. The
indicator light on the panel will begin to blink and
the opener lights will flash once.
3. Release the remote push button.
Now the opener will operate when that remote control
button is pressed. Test it by pressing the remote
button to see that the door goes up and down.
Adding a remote can also be done from the door
control, as follows:
1. With the door closed, press and hold a remote
push button.
2. Press and hold the Light button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button.
To Erase All Remote Control Codes
Press and hold the "Smart" button on the opener panel
until the indicator light turns off (about 6 seconds). All
transmitter codes are now erased. Then follow the
steps above to re-program each remote control.
To Control the Opener Lights
With SECURITY transmitters, a remote push button
can be programmed to operate the opener lights
without opening the door.
1. With the door closed, press and hold the remote
button that you want to control the light.
2. Press and hold the Light button on the door
control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener
lights should turn on or off but the door should not
move.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause serious
injury or death. Do not allow children to operate
the door controls or remote controls.
A moving garage door could injure or kill
someone under it. Activate the opener only
when you can see the door clearly, it is free of
obstructions, and is properly adjusted.
Model 973LM
SECURITY
3-Channel Remote Control
Select a
Push Button
Figure 2
1
Open/Close/Stop Operation
Your SECURITY remote control can be programmed
to operate one door using all 3 buttons: the large
button will only open the door, the middle button will
only close the door, and the third button will stop the
door's movement. You may set up this feature as
follows:
1. With the door closed, press and hold the
large remote push button.
2. Press and hold the Lock button
on the door control.
3. Press and hold the door control
push bar.
When the opener lights flash, release all buttons. Test
by pressing the large (Open) button on the remote.
The door should open. Press it again while the door is
open and nothing should happen. Press the middle
(Close) button and the door should close. Press the
third (Stop) button while the door is moving and it
should stop immediately.
Model 976LM SECURITY Keyless Entry
Follow instructions on page 34 (Accessories).
29
WARNING
Figure 1
SECURITY
Garage Door Opener
1 2
9 1
7 3
5
KG
"Smart" (learn)
Button Indicator Light
RIGHT PANEL
2 3
9 1 9 1
7 3 7 3
5 5
KG KG
Code programming instructions
are also located
on the opener panel.
Stop
3
9 1
7 3
5
KG
Open
Close