Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
READ BEFORE INSTALLING
UNIT
For SLO3 Air Conditoner (8,000-12,000
BTU)
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
Tools and Parts:
Gather
the required
tools and parts before starting
installation.
Read and follow the instructions
provided
with any tools
listed here.
TOOLS NEEDED
•
Flat-blade
and Phillips
screwdrivers
•
Tape measure
•
Level
•
Drill and 3/16", 1/8"_ 3/32", or smaller
drill bit
Through-the-wall
Installation:
In addition
to the tools listed above, the following
tools are needed for through-the-wall
installation.
TOOLS
NEEDED
o saw
•
1°' (2.5 cm) or thicker lumber
® caulk
• #10 X 1" wood screws (7)
Parts Supplied
Check that all parts are included
in parts package:
Hardware
Qty.
Hardware
#10 X 1/2" pan - head
Phillips screws
#10 X 1/2" round - head
screws
#10 X 1/4" pan - head
Phillips screws
Top channel
side curtains
Window sash seal
5
Foam seal
window
lock bracket
2
_
Safety Lock
_1
(for Vinyl-Clad
window)
weather seals
(6"X3/4"X1/12")
Qty.
1
2
5
2020217A2196
Advertisement
Related Manuals for Frigidaire FRA08PZU111
Summary of Contents for Frigidaire FRA08PZU111
- Page 1 READ BEFORE INSTALLING UNIT For SLO3 Air Conditoner (8,000-12,000 BTU) Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices. To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight hazard.
- Page 2 • Installation parts are supplied for double-hung windows up to 36" (91.4 cm) wide. A special Wide Window Kit is available from your dealer or service center. See "Accessories." • Do not use any screws other than those specified here. Location Requirements: IMPORTANT:Observe...
- Page 3 FIG.3A FIG.3B FIG.4 FIG.5 B ,Y electronics plug B. front panel screw C. handle A. shipping screw + Handle the air conditioner gently. + Be sure your air conditioner cabinet does not fall out of the opening during installation or removal. •...
- Page 4 Attach foam adhesive seal: Attach foam adhesive seal along the bottom of the curtain bottom channel (FIG.8). FIG.10 FIG.9 A_g_ket fsCeacbuinee tys eated ............on edge of inner silt. _binet ...... _'neUr°_,, wintdow [--J Bracket A. Curtain housing outer sill B.
- Page 5 FIG.15 Complete Installation: 1. Insert window sash seal behind the top of the lower window sash and against the glass of the upper window (FIG. 15). 2. Place the window-lock bracket on top of lower window and against upper window sash on right side of the window (FIG. 15). 3.
- Page 6 • Dimension f ordepthdepends o nwallthickness a ndtypeof molding (FIG.21). FIG. o Donotblocklouvers in airconditioner cabinet. • Use1"(2.5cm)or thickerlumber f orwood frame. A.Outside width C.Depth B.Outside height Install Cabinet into Wood Frame: 1. Insert cabinet into the framed wall opening. The top of the cabinet should extend 314 °' (19.1 mm) into the room. If there is trim, the cabinet should extend 3/4°' (19.1 mm) past trim (FIG.22).