Digital Camera User’s Guide Thank you for purchasing this CASIO product. • Before using it, be sure to read the precautions contained in this User’s Guide. • Keep the User’s Guide in a safe place for future reference. • For the most up-to-date information about this product, visit the official EXILIM...
Accessories As you unpack your camera, check to make sure that all accessories shown below are included. If anything is missing, contact your original retailer. Rechargeable lithium ion USB-AC adaptor battery (NP-130A) (AD-C54UG/AD-C53U) Power cord USB cable Basic Reference Neck strap The type of USB-AC adaptor included varies according to the country or geographic area where the camera is sold.
Attaching the Neck Strap to the Camera Undo the strap from the buckle Pass the end of the strap and remove the strap loop through the strap loop ring and secure it with the buckle. Buckle Attach the loop on the other end of the strap to the strap hole on one side of the camera, and...
CASIO COMPUTER CO., LTD. is forbidden under copyright laws. • CASIO COMPUTER CO., LTD. shall not be held liable for any damages or lost profits suffered by you or any third party due to the use or malfunction of this product.
General Guide The numbers in parentheses indicate the pages where each item is explained. Front Back bn 7 ck bt bs Mode dial Lens [SET] button (pages 34, 42, 71) Microphones (page 72) (pages 44, 71, 106) Zoom controller [RING] button [MENU] button (pages 35, 58, 134) (pages 45, 133)
Bottom Battery/memory card slots (pages 21, 30) Battery cover Tripod hole Use this hole when attaching to a tripod. Speaker . Control Dial In addition to using the up, down, left, and right buttons, you can also use the control dial to perform operations.
Monitor Screen Contents and How to Change Them The monitor screen uses various indicators, icons, and values to keep you informed of the camera’s status. • The sample screens in this section are intended to show you the locations of all the indicators and figures that can appear on the monitor screen in various modes.
. CS Image Viewing Number of images in the group (page 129) CS group icon (page 129) . Movie Playback No audio data available Movie recording time (page 127) Recording mode/Movie quality/speed (pages 71, 74, 74) YouTube (page 80) . Configuring Monitor Screen Settings Each press of [8] (DISP) will cycle through display settings that display or hide on-screen information.
Quick Start Basics What you can do with your CASIO camera Your CASIO camera is packed with a powerful selection of features and functions to make recording of digital images easier, including the following main functions. Tiltable Monitor Screen 180 degrees The camera’s monitor screen can be tiled upwards...
Blurred Background This function analyzes a burst of consecutive images and then blurs the background behind the main subject. This creates an effect that really makes the subject stand out, just like photographs taken with a single-lens reflex camera. *See page for more information.
Tilting the Monitor Screen The monitor screen can be tilted upwards up to 180 degrees. This means you can position 180 degrees the monitor screen so it faces in the same direction as the lens, for easy composition of self-portraits. You can also tilt the monitor screen upwards 90 degrees, which means you can easily shoot from a low angle 90 degrees...
. Tilting the Monitor Screen As shown in the figure below, pull upwards on the bottom center of the monitor screen at point . The monitor screen will open up to 90 degrees and stop momentarily. Keep lifting and it will tilt upwards up to 180 degrees. •...
Page 20
. Returning the Monitor Screen to Its Normal Position Holding the monitor screen at Push the monitor screen point , rotate the screen downwards with your finger at downwards to the back of the point to slide the monitor camera. screen down as far as it will go.
Note that the battery of a newly purchased camera is not charged. Perform the steps below to load the battery into the camera and charge it. • Your camera requires a special CASIO rechargeable lithium ion battery (NP-130A or NP-130) for power. Never try to use any other type of battery.
Page 22
Load the battery. Stopper With the CASIO logo on the battery facing downwards (in the direction of the lens), hold the stopper next to the battery in the direction indicated by the arrow as you slide the battery into the camera. Press the battery in until the stopper secures it in place.
Charge the Battery You can use either of the two following methods to charge the camera’s battery. • USB-AC adaptor • USB connection to a computer (Using the included USB cable.) . To charge with the USB-AC adaptor The adaptor lets you charge the battery while it is loaded in the camera. While the camera is turned off, connect in the sequence shown below.
Page 24
IMPORTANT! • A battery that has not been used for a long time, or ambient temperature extremes can cause charging to take longer than normal. If charging takes longer than about five hours, a timer will terminate it automatically, even if the battery is not fully charged.
Page 25
. To charge using a USB connection to a computer USB connection lets you charge the battery while it is loaded in the camera. While the camera is turned off, connect in the sequence shown below ( Computer (power turned on) USB port [USB/AV] port USB cable...
Page 26
Back Lamp Operation Back lamp Lamp Status Description Lit Red, Charging (Lit/Flashing Amber) Abnormal ambient temperature, Flashing Red charging taking abnormally long, or battery problem (page 196) Off, (Lit Green) Charging complete • The information in parentheses in the above table shows the lamp status while the camera is turned on during charging.
Checking Remaining Battery Power As battery power is consumed, a battery indicator on the monitor screen indicates remaining power as shown below. Remaining Power High Battery Indicator Indicator Color White * White indicates battery power is low. Charge the battery as soon as possible. Recording is not possible when is indicated.
Page 28
Press [ON/OFF] (Power) to turn on the [ON/OFF] (Power) camera. Use [8], [2], [4], and [6] to select the language you want and then press [SET]. Use [8] and [2] to select a date style and then press [SET]. Example: July 10, 2015 YY/MM/DD 15/7/10 DD/MM/YY...
Ultra High Speed Type SD memory card is recommended. Note, however that CASIO makes no guarantees about the operation of any Ultra High Speed Type SD memory card used with this camera.
• Never insert anything besides a supported memory card (page 29) into the memory card slot. • Should water or any foreign object ever get into the card slot, immediately turn off the camera, remove the battery, and contact your retailer or nearest CASIO authorized service center. Quick Start Basics...
To replace the memory card Press the memory card and then release it. This will cause it to pop out of the memory card slot slightly. Pull the card out the rest of the way and then insert another one. •...
Turning the Camera On and Off . To turn power on Pressing [ON/OFF] (Power) enters the [ON/OFF] (Power) REC mode so you can record images. Pressing [p] (PLAY) while in the REC Shutter button mode enters the PLAY mode, which you can use to view snapshots and movies Back lamp (pages 38, 127).
Holding the Camera Correctly Your images will not come out Horizontal Vertical clearly if you move the camera when you press the shutter button. When pressing the shutter button, be sure to hold the camera as shown in the illustration, and keep it still by pressing your arms firmly against your sides as you shoot.
To shoot a snapshot Selecting an Auto Recording Mode You can select one of two auto recording modes (Program Auto or Premium Auto Pro) according to your digital imaging needs. REC Screen Setting Description Icon Display Program This is the standard Auto recording mode. Auto With Premium Auto Pro recording, the camera automatically determines whether you are shooting a...
To shoot a snapshot Point the camera at the subject. If you are shooting with Premium Auto Pro, text will appear at the bottom of the monitor screen describing the type of shot the camera has detected. • You can zoom the image, if you want. Appears when the camera detects it is stationary on a tripod.
Continuing to keep the camera still, Full-press press the shutter button the rest of the way down. This records the snapshot. Snap (Image is recorded.) Recording a Movie [0] (Movie) Press [0] (Movie) to start movie recording. Press [0] (Movie) again to stop movie recording. See the following pages for details.
Page 37
. Shooting with Premium Auto Pro • In addition to shutter speed, aperture, and ISO sensitivity, the camera automatically executes the following operation as required when shooting with Premium Auto Pro. – Continuous AF (page 118) – Intelligent AF (page 115) –...
Viewing Snapshots Use the following procedure to view snapshots on the camera’s monitor screen. • For information about how to play back movies, see page 127. • For information about images recorded using continuous shutter (CS), see page 129. Turn on the camera and press [p] (PLAY) to enter the PLAY mode.
Deleting Snapshots and Movies If memory becomes full, you can delete snapshots and movies you no longer need in order to free up storage and record more images. IMPORTANT! • Remember that a file (image) delete operation cannot be undone. •...
. To delete all files Press [p] (PLAY) to enter the PLAY mode and then press [2] ( Use [8] and [2] to select “Delete All Files” and then press [SET]. Use [8] and [2] to select “Yes” and then press [SET] to delete all files. This will cause the message “There are no files.”...
. Auto Focus Restrictions • Any of the following can make proper focus impossible. – Solid color wall or other very low contrast subject – Strongly back lit subject – Very shiny subject – Blinds or other subject with a repeating horizontal pattern –...
Snapshot Tutorial Selecting the Recording Mode Your camera has a variety of different recording Mode dial modes. Before recording an image, rotate the mode dial to select the recording mode that suits the type of image you are trying to record. P Program Auto Standard Auto recording mode.
Page 43
M M (Manual Exposure) mode This mode gives you total control over aperture and shutter speed settings. Press [SET] to open the Control Panel. Use [8] and [2] to select (Aperture), and then press [SET]. Use [8] and [2] to change the aperture setting, and then press [SET]. Use [8] and [2] to select (Shutter Speed), and then press [SET].
Using the Control Panel The Control Panel can be used to configure camera [8] [2] [4] [6] settings. In the REC mode, press [SET]. [SET] • You can also display the Control Panel by pressing [2]. Use [8] and [2] to select the setting you want to change, and then press [SET].
Configuring Camera Settings with the Function Ring Control Panel and menu item functions can be assigned to the function ring. After that, camera settings can be easily configured by rotating the function ring. Functions that can be assigned to the function ring depend on the recording mode. [SET] [RING] [8] [2] [4] [6]...
Using the Self-timer (Self-timer) With the Self-timer, pressing the shutter button starts a timer. The shutter is released and the image is shot after a fixed amount of time. In the REC mode, press [SET]. Use [8] and [2] to select the (Self-timer) Control Panel option, and then press [SET].
NOTE • The Self-timer cannot be used together with the following features. High Speed CS with Prerecord CS, Prerecord (Movie), Slide Panorama, Wide Shot, Triple Shot • The Triple Self-timer cannot be used together with the following features. Movie, Time Lapse, High Speed CS, Multi SR Zoom, HS Night Shot, HS Best Selection, For YouTube, Blurred Background, All-In-Focus Macro •...
Page 48
REC Screen Setting Description Icon Display Tungsten For shooting under light bulb lighting « For configuring the camera manually to suit a particular light source Select “Manual WB”. Blank white paper Under the lighting conditions you plan to use when shooting, point ·...
Selecting a Focus Mode (Focus) • The “Focus” setting is always fixed at “AF” (Auto Focus) whenever “Face Detection” (page 119) is being used. If you want to change the “Focus” setting, first select “Off” for “Face Detection”. In the REC mode, press [SET]. Use [8] and [2] to select the (Focus) Control Panel option, and then press [SET].
Super Macro Super Macro fixes optical zoom at a position that allows you to shoot from the closest distance to the subject. The result is closer and larger subject images. NOTE • Zoom is fixed while Super Macro is selected, so no zoom operation is performed when you rotate the zoom controller.
Using Focus Lock Subject to be focused on “Focus lock” is a technique you can use when you want to compose an image in which the subject you want to focus on is not within the focus frame in the center of the screen.
Page 52
Use [8] and [2] to select the setting you want and then press [SET]. REC Screen Setting Description Icon Display Adjusts sensitivity automatically according to Auto None conditions. ISO80 Lower Slow shutter speed Less noise sensitivity ISO100 ISO200 ISO400 ISO800 Fast shutter speed Some coarseness ISO1600...
Recording Beautiful Portraits (Make-up Level) The Make-up Function smoothes the skin texture of the subject and softens facial shadows caused by harsh sunlight for better looking portraits. You can select a make- up level within the range of “0 (Off)” to “+12 (Max.)”. Enter the REC mode, and then press [SET].
Correcting Image Brightness (EV Shift) You can manually adjust an image’s exposure value (EV value) before shooting it. • Exposure Compensation Range: –2.0 EV to +2.0 EV • Unit: 1/3EV In the REC mode, press [SET]. Use [8] and [2] to select the (EV Shift) Control Panel option, and then press [SET].
Using Flash (Flash) In the REC mode, press [2] ( Flash once. Use [8] and [2] to select the flash setting you want and then [2] ( press [SET]. REC Screen Setting Description Icon Display Flash fires automatically in accordance with Auto Flash None exposure (amount of light and brightness)
Page 56
NOTE • Take care so your fingers and the strap do not block the flash. • The desired effect may not be obtained when the subject is too far away or too close. • Flash charging time (page 213) depends on operating conditions (battery condition, ambient temperature, etc.).
Specifying the Metering Mode (Metering) The metering mode determines what part of the subject is metered for exposure. In the REC mode, press [SET]. Use [8] and [2] to select the (Metering) Control Panel option, and then press [SET]. Use [8] and [2] to select the setting you want and then press [SET]. REC Screen Setting Description...
Shooting with Zoom Your camera is equipped with various types of zoom: optical zoom, HD Zoom, Single SR Zoom, Multi SR Zoom, and digital zoom. The maximum zoom factor depends on the image size setting and the digital zoom on/off settings. Zooming is performed by changing the lens focal distance, so Optical zoom there is no deterioration of image quality.
Page 59
NOTE • Use of a tripod is recommended to protect against image blur due to camera movement when shooting with telephoto. • Performing a zoom operation changes the lens aperture. • Zoom operations are supported during movie recording. Zoom operations are disabled during high speed movie recording.
Monitor Screen Information when Zooming A variety of information is shown on the monitor screen while a zoom operation is in progress. . Zoom Mode Icons Zoom mode Focal distance (Converted to 35 mm film Focusing Range format.) (Displayed for Auto Focus, Macro Focus, and Manual Focus.) Image quality limit...
. Interpreting the Zoom Bar During a zoom operation, a zoom bar appears on the monitor screen to show the current zoom setting. Range where image deterioration is Deteriorated image range suppressed. Wide Angle Telephoto Zoom pointer Optical zoom limit point (Indicates current zoom.) Point from which image deteriorates •...
Zooming with Super Resolution (Zoom (SR)) There are two types of Super Resolution Zoom: Single SR Zoom and Multi SR Zoom. Single SR Zoom uses super resolution to expand the zoom range in which image quality deterioration is minimized. Multi SR Zoom shoots a series of High Speed CS images, which are then combined into an image that enables shooting at higher zoom ratios without loss of image quality.
Expanding the Zoom Range to Shoot Clearer Snapshots (Multi SR Zoom) This feature uses super resolution technology and multiple Continuous Shutter (CS) images to expand the zoom range for overall images of higher quality and clarity (page 62). Align the mode dial with [j] (Multi SR Zoom). Press the shutter button to shoot.
Page 64
Facing the camera, move your hand or perform some other movement in the vicinity of the (start self-timer) icon on the monitor screen. When the camera detects movement near the icon, it will automatically shoot an image. • To stop movie recording, press [0] (Movie) again. NOTE •...
Configuring Handsfree Mode Settings (Handsfree) Use the procedure below to configure Handsfree Mode settings. In the REC mode, press [MENU]. Press [4], use [8] and [2] to select the “ r REC MENU” tab, and then press [6]. Use [8] and [2] to select “Handsfree” and then press [SET]. Configure Handsfree settings.
Repositioning the Motion Detection Area (Motion Position) Use the procedure below to reposition the motion detection area (Start self-timer icon) as required when it (or the preview icon ) hinders your view of the display image. In the REC mode, press [MENU]. Start self-timer icon Press [4], use [8] and [2] to select the “...
Shooting with Artistic Effects (ART SHOT) A variety of artistic effects help to make even common, ordinary subjects become more novel and exciting. Scene Description Applies HDR (High Dynamic Range, page 89) photography to transform snapshots and movies into works of art that HDR Art provide a greater degree of expression than conventional imaging.
Page 68
Press [SET], use [8] and [2] to select the fifth Control Panel option from the top, and then press [SET]. The intensity of the selected effect can be adjusted as described below. Scene Adjustment HDR Art Effect level Toy Camera Soft Focus Effect level Light Tone...
NOTE • Depending on the “ART SHOT” scenes, some of the items on the menu that appears may not be usable. • With this “ART SHOT” scene, the flash setting automatically becomes ? (Flash Off). • Movie recording is disabled while “Sparkling Shot” is selected. •...
Shooting with Triple Shot Triple Shot shoots a burst of three images and stores them in memory. This feature is great for making sure you don’t miss those special moments when kids are around. Align the mode dial with [D] (Triple Shot). Point the camera at the subject and then half-press the shutter button.
Recording Movies To record a movie The following procedure explains how to record a standard (STD) movie. This camera supports Premium Auto Pro movie recording (page 72). See the pages indicated below for more information about movies. High-definition movie (FHD movie): page 74 Mode dial High speed movie (HS movie): page 74 Align the mode dial with [P] (Program...
Recording Movies with Premium Auto Pro When Premium Auto Pro is enabled (page 34), the camera automatically make judgments about the subject, shooting conditions, and other parameters. The result is higher quality images than those produced by Program Auto recording. The shooting environment detected by the camera is displayed at the bottom of the REC mode screen.
Page 73
IMPORTANT! • Spending a long time using movie recording will cause the camera to become slightly warm to the touch. This is normal and does not indicate malfunction. • Shooting movies for long periods in areas where temperature is relatively high can cause digital noise (dots of light) to appear in the movie image.
Recording a High-definition Movie This camera supports recording of high-definition (FHD) movies. The aspect ratio of an FHD movie is 16:9, the image size is 1920 1080 pixels, and the frame rate is 30 fps. Image quality and image size settings cannot be changed. Align the mode dial with [P] (Program Auto) or [Ÿ] (Premium Auto Pro).
Page 75
Use [8] and [2] to select “Movie Quality” and then press [6]. Use [8] and [2] to select the frame rate (recording speed) you want and then press [SET]. A fast frame rate (such as 1000 fps) will result in a smaller image size. Movie REC Screen Image Size...
NOTE • The higher the frame rate (speed), the more lighting is required when shooting. When shooting a high speed movie, shoot in a well-lit environment. • When recording certain types of movies, the image that appears on the monitor screen may be smaller than normal.
Page 77
. To set up the camera to shoot with Prerecord Movie Align the mode dial with [b] (BEST SHOT). Press [MENU]. Press [4], use [8] and [2] to select the “ r REC MENU” tab, and then press [SET]. Use [8] and [2] to select “Movie Quality” and then press [6]. Use [8] and [2] to select the movie mode you want to use for shooting and then press [SET].
NOTE • While the camera is set up for shooting with Prerecord Movie, pressing the shutter button will not shoot a snapshot unless movie recording is in progress. With high- definition (FHD) and standard (STD) movie, you can shoot still images while realtime movie recording is in progress.
Page 79
Press [SET]. • Time Lapse settings are shown at the bottom of the screen. Interval Scene Total Time Press the shutter button to start recording. Recording time • Shooting is repeated at the interval specified in step 6. • Recording stops when the recording time specified in step 6 elapses or when the shutter button is pressed again.
• To adjust brightness when shooting with the Time Lapse “Night Scene”, use “ ” (Shutter Speed) on the Control Panel (page 44) to adjust the shutter speed. . Using the Scene Information Screen To find out more about a scene, select it with the boundary on the scene menu and then rotate the zoom controller in either direction.
NOTE • Movies recorded with the “For YouTube” scene are stored in a special folder to make them easy to locate for uploading (page 172). “For YouTube” movies are shot using the image size, recording speed, and quality settings configured in the Movie Mode (page 71).
Page 82
NOTE • Note that the flash cannot be used when shooting a Snapshot In Movie. • Note that shooting a snapshot while shooting a movie is supported during FHD movie and STD movie recording only. It is not supported during other types of movie recording.
Using BEST SHOT BEST SHOT provides you with a collection of sample “scenes” that show a variety of different types of shooting conditions. When you need to change the setup of the camera, simply find the scene that matches what you are trying to achieve, and the camera sets up for it automatically.
Page 84
Press [SET] to configure the camera with the settings for the currently selected scene. This returns to the REC mode. • To select a different BEST SHOT scene, repeat the above procedure from step 2. Press the shutter button (if you are shooting a snapshot) or [0] (Movie) (if you are shooting a movie).
Creating and Using Your Own Setups (CUSTOM SHOT) You can register up to 999 setups, based on snapshots shot with the camera, as “CUSTOM SHOT” scenes. Selecting a registered “CUSTOM SHOT” scene configures the camera with its settings. The setups of snapshots recorded with the following modes and features can be registered as “CUSTOM SHOT”...
. To record with a registered CUSTOM SHOT scene Align the mode dial with [b] (BEST SHOT). Press [SET]. Use [8] and [2] to select , and then press [SET]. Select the registered “Custom Scene”, and then press [SET]. Press the shutter button to shoot. Shooting with a Face Brightening Effect (Brightening) This effect can be used to brighten the facial tones of subjects.
Shooting with High Speed Anti Shake (HS Anti Shake) When you press the shutter button while HS Anti Shake is enabled, the camera records multiple images and automatically combines them in a way that produces a final image with minimal blur. You can shoot with this feature to minimize the effects of camera movement when shooting with optical Anti Shake does not produce the desired results.
Shooting Bright Images in the Dark without Flash (HS Night Shot) The camera shoots a series of images and then merges them into a final image. The result is a bright image, even if shot in the dark without a flash. Shot with “Program Auto”, without flash Shot with “HS Night Shot”...
Digitally Correcting for Overexposure and Underexposure (HDR) With HDR (High Dynamic Range), the camera shoots a series of CS images using different exposure settings and combines them into a final image to correct for overexposure or underexposure of subjects of different brightness levels. Align the mode dial with [b] (BEST SHOT).
Shooting with a Blurred Background (Blurred Background) This function analyzes a burst of consecutive images and then blurs the background behind the main subject. This creates an effect that really makes the subject stand out, just like photographs taken with a single-lens reflex camera. The blur effect can be set to one of three levels.
NOTE • With this function, the flash setting automatically becomes ? (Flash Off). • Shooting with this function automatically sets Anti Shake to “Standard” (page 116), but large movement of the camera or subject make it impossible to achieve the desired shot.
NOTE • When shooting with this function, zoom is fixed at wide angle. • When shooting with this function, the flash setting automatically becomes ? (Flash Off). • Shooting with this function automatically sets Anti Shake to “Standard” (page 116), but large movement of the camera or subject make it impossible to achieve the desired shot.
Shooting a Burst of Images (High Speed CS) You can use the procedures in this section to specify the speed, number of images, and other settings for High Speed CS (Continuous Shutter). . Shooting with High Speed CS With High Speed CS, recording continues as long as you CS speed keep the shutter button depressed.
Use [8] and [2] to select the (Maximum CS Shots) Control Panel option and then press [SET]. Use [8] and [2] to select the maximum number of shots and then press [SET]. Press the shutter button the rest of the way and hold it down. Shooting of images will continue as long as you depress the shutter button or until the maximum number of images specified by “High Speed CS fps”...
Use [8] and [2] to select the (Maximum CS Shots) Control Panel option and then press [SET]. Use [8] and [2] to select the maximum number of shots and then press [4]. Use [8] and [2] to select the (Pre-record CS Shots) Control Panel option and then press [SET].
• Single SR Zoom cannot be used when shooting with this function. Shooting with Priority on Subject Faces (HS Best Selection) With HS Best Selection, the camera automatically shoots a series of images, and selects the best one based on facial image blur, and facial expression (whether the subject is smiling or blinking).
Shooting a Panorama Image (Slide Panorama) With Slide Panorama, you move the camera to compose and record multiple images, which are then combined to a panorama. This feature lets you shoot a panorama of up to 360 degrees, which is dramatically greater than the physical capabilities of the lens.
Page 98
Press the shutter button the rest of the way down and a slide cursor will appear on the monitor screen. Slowly move the camera in the direction indicated by the arrow on the screen until the slide cursor reaches the other end of its movement range (i.e.
Shooting with a Super Wide Angle of View (Wide Shot) With this feature, a number of images are shot and then combined to produce an image with a super-wide angle of view that exceeds the widest angle of view possible with the lens.
Page 100
Point the camera at the subject you want in the center of the image and then half-press the shutter button to focus. • The outer blue boundary on the screen indicates the Desired image recordable range of the image. Blue boundary Center part at the start of the shooting operation Press the shutter button the rest of the way...
Page 101
NOTE • The “14 mm” and “18 mm” angle of view values are approximate and are provided for reference only. Actual angle of view values are not guaranteed. • Zoom operations are not supported during Wide Shot shooting. The zoom setting is fixed at full wide angle.
Shooting Snapshots (Snapshot) This function adjusts exposure and shoots whenever the shutter button is half- pressed. This helps to ensure that you don’t miss the shots you want. This feature comes in handy for daily shooting and when shooting natural scenery. Align the mode dial with [b] (BEST SHOT).
Shooting RAW Images (Raw Image) You can configure the camera to save a RAW image along with a standard JPEG image when shooting snapshots. RAW image data is stored in a camera folder named “RAW” (page 172). A RAW image is image data (file name extension .DNG) that is unprocessed internally by the camera.
Using a TV Screen to Shoot Snapshots (HDMI TV Output) Use the procedure below to configure the camera for shooting snapshots with an aspect ratio of 16:9, as you compose them on a TV screen. Turn off the camera and use a commercially available HDMI cable to connect the camera to a TV.
Page 105
NOTE • For details about connecting to the camera and precautions when connecting, see page 135. • If you want to change the digital video signal format, first unplug the HDMI cable from the camera (page 137). • The settings in the table below are fixed while shooting with this function. Image Size 16:9 AF Area...
Advanced Settings (REC MENU) The following are menu operations you can use to configure various camera settings. • You also can use the Control Panel (page 44) to configure some of the settings that appear on the menu screen. Refer to the page references provided in this section for information about configuring settings using the Control Panel.
. Menu Operations in This Manual Menu operations are represented in this manual as shown below. The following operation is the same as the one described under “Example Menu Screen Operation” on page 106. Press [4] and then use [8] and [2] to select the “...
Assigning Functions to the Control Dial (Control Dial) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Control Dial You can assign any one of the four functions below to the control dial. After you do, you can change the setting of the function by rotating the control dial.
Assigning Functions to the [4] and [6] Keys (L/R Key) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * L/R Key You can select from among the functions described below and assign one to the [4] and [6] keys (Key Customize).
To select the snapshot image size (Image Size) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Image Size Suggested Image Size REC Screen Print Size and Description (Pixels) Icon Display Application Poster Print (4608 3456) Good detail for better clarity even for Poster Print...
Page 111
• Available image sizes are limited for some functions as noted below. This image size cannot be selected when using “HS Night Shot”. Selecting “16M” in another mode and then switching to “HS Night Shot” will cause the image size to change to “10M” automatically. These image sizes cannot be selected when using “High Speed CS”...
Specifying Snapshot Image Quality (Image Quality) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Image Quality REC Screen Icon Setting Description Display Fine Gives image quality priority. Normal Normal • The “Fine” setting helps to bring out details when shooting a finely detailed image of nature that includes dense tree branches or leaves, or an image of a complex pattern.
Page 113
Settings REC Screen Approximate Data Rate (Quality Description Icon Display (Frame Rate) (pixels)) Select this setting record high- definition (HD) movies. The aspect ratio of movies recorded with this setting is 16:9. • “HD” can be selected in place of 10.9 Megabits/second “FHD”...
Specifying ISO Sensitivity (ISO) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * ISO For details, see the Control Panel procedure on page 51. Specifying the ISO Sensitivity Upper Limit (ISO High Limit) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * ISO High Limit REC Screen Settings...
Zooming with Super Resolution (Zoom (SR)) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Zoom (SR) See page 62 for details. Specifying the Auto Focus Area (AF Area) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * AF Area You can use the following procedure to change the Auto Focus metering area for shooting snapshots.
IMPORTANT! • Auto Focus is disabled when “MF” (Manual Focus) is selected for the focus mode (page 49), even if you select an AF area. • Selecting “O Tracking” can cause vibration and noise to occur due to lens operation while tracking a subject. This does not indicate malfunction. •...
Page 117
NOTE • Only camera shake correction can be used during FHD and STD movie recording. • Anti Shake correction is not supported during High Speed Movie, HDR Art Movie recording or Time Lapse. • When Anti Shake is enabled and “Auto” is selected for “ISO” (page 51), ISO sensitivity, aperture, and shutter speed will not appear on the monitor screen when you half-press the shutter button.
Optimizing Image Brightness (Lighting) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Lighting You can use this setting to optimize the balance between bright areas and dark areas when shooting images. Settings Description Performs brightness correction. When this option is selected, it takes longer for the image to be stored after the shutter button is pressed.
Shooting with Face Detection (Face Detection) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Face Detection When shooting people, the face detection feature detects the faces of up to ten individuals and adjusts focus and brightness accordingly. Use [8] and [2] to select “On”...
Turning Digital Zoom On or Off (Digital Zoom) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Digital Zoom Select “On” when you want to use digital zoom (page 58). • Digital zoom is disabled while shooting with the following feature. –...
Correcting Image Brightness (EV Shift) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * EV Shift For details, see the Control Panel procedure on page 54. Adjusting White Balance (White Balance) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * White Balance For details, see the Control Panel procedure on page 47.
Specifying Flash Intensity (Flash Intensity) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Flash Intensity You can specify flash intensity to one of five levels from +2 (brightest flash) to –2 (least bright flash). •...
Using the Auto Focus Assist Light (AF Assist Light) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * AF Assist Light Half-pressing the shutter button while this setting is selected Front lamp causes the front lamp to light, which provides illumination for focusing in areas where lighting is dim.
Using Icon Help (Icon Help) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Icon Help While Icon Help is turned on, a textual description will appear on the display for certain icons when you switch between REC functions. Functions Supported by Icon Help •...
Selecting “On” for this setting displays a semitransparent gray frame on the monitor screen. The area within the frame is what is Movie Range recorded as the movie. Semi-transparent gray frame . How to Use the Histogram A histogram is a graph that represents the lightness of an image in terms of the number of pixels.
Configuring Power On Default Settings (Memory) Procedure Enter the REC Mode * [MENU] * “ r REC MENU” Tab * Memory This setting lets you specify which camera settings should be remembered by the camera when it is turned off, and restored the next time the camera is turned on. To have the camera remember a setting, you should enable the setting’s memory.
Viewing Snapshots and Movies Viewing Snapshots See page 38 for the procedure for viewing snapshots. Viewing a Movie Press [p] (PLAY) and then use [4] and [6] to display the movie you want to view. Press [SET] to start playback. Movie icon: »/»...
Rotate the zoom controller in the direction of z ([). • You can use [8], [2], [4], and [6] to scroll the zoomed image on the monitor screen. You can zoom a movie Zoom image up to 4.5 times normal size. •...
Viewing Continuous Shutter Images Each time you perform a continuous shutter (CS) operation, the camera creates a CS group that includes all of the images for that particular CS session. You can use the following procedure to play back the images in a particular CS group. Press [p] (PLAY) and then use [4] and [6] to display the CS group whose images you want to view.
Playback Controls During playback, changes the playback direction and playback speed. While playback is paused, scrolls forward or back. [4] [6] • Forward and back scrolling can also be performed using the function ring. • Playback speed cannot be adjusted while the displayed image is zoomed.
Page 131
. Deleting Multiple Files in a CS Group While CS image playback is in progress or paused, press [2]. This will display the “CS Frame Edit” menu. Use [8] and [2] to select “Delete” and then press [SET]. Use [8] and [2] to select “Delete Frames” and then press [SET]. This displays a file selection screen.
Dividing Up a CS Group Use the following to divide up a CS Group into individual images. . Dividing Up a Specific CS Group In the PLAY mode, press [MENU]. Press [4], use [8] and [2] to select the “p PLAY MENU” tab, and then press [SET].
Copying a CS Group Image Use the following procedure to copy an image in a CS group to a location outside of the group. While CS image playback is in progress or paused, press [2]. This will display the “CS Frame Edit” menu. Use [8] and [2] to select “Copy”, and then press [SET].
Zooming an On-screen Image In the PLAY mode, use [4] and [6] to scroll through the images until the one you want is displayed. Rotate the zoom controller towards z ([) to Zoom factor zoom. Image area You can use [8], [2], [4], and [6] to scroll the zoomed image on the monitor screen.
Viewing Snapshots and Movies on a TV Screen Use the optionally available AV cable (EMC-8A) to connect the camera to the TV. • For details about connecting to the camera and precautions when connecting, see page 25. AV cable (EMC-8A) Yellow White Video...
NOTE • Audio is stereo. • Some TVs may not be able to output images and/or audio correctly. • All icons and indicators that appear on the monitor screen also appear on the TV screen. You can use [8] (DISP) to change the display contents. •...
Page 137
NOTE • Use a HDMI cable that with a plug that is compatible with the camera’s HDMI mini connector on one end, and a plug that is compatible with your TV’s HDMI connector on the other end. • Proper image and/or audio output and other operations may not be possible with some devices.
Page 138
Recording Camera Images to a DVD Recorder or Video Deck Use the following method to connect the camera to the recording device using the AV cable (option). – DVD recorder or video deck: Connect the AV cable to the VIDEO IN and AUDIO IN terminals.
Other Playback Functions (PLAY MENU) This section explains menu items that you can use to configure settings and perform other playback operations. For information about menu operations, see page 106. Playing a Slideshow on the Camera (Slideshow) Procedure [p] (PLAY) * [MENU] * “p PLAY MENU” Tab * Slideshow Start Starts the slideshow Images...
Page 140
Effect Select the effect you want. Pattern 1 to 5: Plays background music and applies an image change effect. • Patterns 2 through 4 have different background music, but they all use the same image change effect. • Pattern 5 can be used for playback of snapshots only (except for those that are part of a CS group), and the “Interval”...
Transferring Music from Your Computer to Camera Memory You can replace the built-in slideshow background music with other music from your computer. Supported File Types: • PCM format (16-bit, monaural / stereo) WAV files • Sampling Frequencies: 11.025 kHz/22.05 kHz/44.1 kHz Number of Files: 9 File names: SSBGM001.WAV to SSBGM009.WAV •...
Creating a Snapshot of Movie Frames (MOTION PRINT) Procedure [p] (PLAY) * Movie Screen * [MENU] * “p PLAY MENU” Tab * MOTION PRINT Use [4] and [6] to scroll through the movie frames and display the one you want to use as the image of the MOTION PRINT image. Holding down [4] or [6] scrolls at high speed.
Page 143
Press [2] to display the editing menu and specify one or two cut points. While the frame you want the cut to be up to is Previous Cut displayed, press [2]. While the frame you want the first (From) cut to be is displayed, press [2].
To merge two movies (Movie Merge) Procedure [p] (PLAY) * Display one of the movies you want to merge. * [MENU] * “p PLAY MENU” Tab * Movie Merge This procedure combines two movies. The play times of each movie must be less than 10 minutes, and the two movies must be of the same quality and frame rate.
Optimizing Image Brightness (Lighting) Procedure [p] (PLAY) * Snapshot Screen * [MENU] * “p PLAY MENU” Tab * Lighting You can use this setting to adjust the balance between bright areas and dark areas in existing images in the range of 0 (no optimization) to +2 (bright). NOTE •...
Adjusting the Brightness of an Existing Snapshot (Brightness) Procedure [p] (PLAY) * Snapshot Screen * [MENU] * “p PLAY MENU” Tab * Brightness You can select one of five brightness levels, from +2 (brightest) to –2 (least bright). NOTE • The original snapshot is retained in memory and not deleted. •...
Page 147
IMPORTANT! • Note that even if a file is protected, it will be deleted if you perform the format operation (page 184). . To protect a specific image in a CS group While CS image playback is in progress or paused, press [2]. This will display the “CS Frame Edit”...
Editing the Date and Time of an Image (Date/Time) Procedure [p] (PLAY) * Snapshot Screen * [MENU] * “p PLAY MENU” Tab * Date/Time [8] [2] Changes the setting at the cursor location. [4] [6] Moves the cursor between settings. When the date and time settings are what you want, align the cursor with “Apply”...
Resizing a Snapshot (Resize) Procedure [p] (PLAY) * Snapshot Screen * [MENU] * “p PLAY MENU” Tab * Resize You can reduce the size of a snapshot and save the result as a separate snapshot. The original snapshot is also retained. You can resize an image to one of three sizes: 10M, 3M, VGA.
Copying Files (Copy) Procedure [p] (PLAY) * Snapshot or Movie Screen * [MENU] * “p PLAY MENU” Tab * Copy Files can be copied from the camera’s built-in memory to a memory card or from a memory card to built-in memory. Copies all files from built-in camera memory to a memory card.
Combining CS Images into a Single Still Image (CS Multi Print) Procedure [p] (PLAY) * Display CS group. * [MENU] * “p PLAY MENU” Tab * CS Multi Print Use [8] and [2] to select “Create”. • You can use [4] and [6] to select a different CS group, if you want. Press [SET].
Printing Printing Snapshots Professional Print Service* You can take a memory card that contains the images you want to print to a professional print service and have them printed. Printing on a Home Printer* Printing Images on a Printer with Memory Card Slot You can use a printer equipped with a memory card slot to print images directly from a memory card.
. Connecting the Camera to a Printer Use the USB cable that comes bundled with the camera to connect the camera to your printer’s USB port. • For details about connecting to the camera and precautions when connecting, see page 25. USB port Small connector Large connector...
Use [8] and [2] to specify the print option you want. 1 Image : Prints one image. Select and then press [SET]. Next, use [4] and [6] to select the image you want to print. DPOF Printing: Prints multiple images. Select and then press [SET]. With this option, images will be printed in accordance with DPOF settings (page 154).
Page 155
. Configuring DPOF Settings Individually for Each Image Procedure [p] (PLAY) * Snapshot Screen * [MENU] * “p PLAY MENU” Tab * DPOF Printing * Select images Use [4] and [6] to scroll through the files until the image you want to print is displayed.
Page 156
. To specify the number of copies for a specific image in a CS group While CS image playback is in progress or paused, press [2]. This will display the “CS Frame Edit” menu. Use [8] and [2] to select “DPOF Printing” and then press [SET]. Use [8] and [2] to select “Select Frames”...
DPOF settings are not cleared automatically after printing is complete. The next DPOF print operation you execute will be performed using the last DPOF settings you configured for the images. To clear DPOF settings, specify “00” for the number of copies of all images. Tell your print service about your DPOF settings! If you take a memory card to a professional print service, be sure to tell them that it includes DPOF settings for the images to be printed and the number of copies.
Page 158
. Standards Supported by the Camera • PictBridge This is a standard of the Camera and Imaging Products Association (CIPA). You can connect the camera directly to a printer that supports PictBridge, and perform image selection and printing using the camera monitor screen and controls.
Using the Camera with a Computer Things you can do using a computer... You can perform the operations described below while the camera is connected to a computer. Save images to • Save images and view them manually (USB a computer and connection) (pages 160, 164).
Using the Camera with a Windows Computer When you want Operating System Install this software: to do this: Version page: Save images to Windows 8, a computer and Windows 7, Installation not required. view them there Windows Vista, manually Windows XP (SP3) Installation not required.
Page 161
. To connect the camera to your computer and save files Turn on the camera and press [MENU]. On the “¥ SETTING” tab, select “USB” and then press [6]. Use [8] and [2] to select “Mass Storage”, and then press [SET]. Turn off the camera and then USB port use the USB cable that comes...
Page 162
Windows 8 users: On the “Documents” menus, click “Home” and then “Paste”. Windows 7 users: On the “Documents” “Organize” menu, select “Paste”. Windows Vista users: On the “Documents” “Edit” menu, select “Paste”. Windows XP users: On the “My Documents” “Edit” menu, select “Paste”.
Playing Movies To play back a movie, first copy it to your computer and then double-click the movie file. Some operating systems may not be able to play back movies. If this happens, you need to install separately available software. •...
Using the Camera with a Macintosh When you want to Operating Install this software: do this: System Version page: Save images to your Macintosh and view OS X Installation not required. them there manually Save images to your Use iPhoto, which comes Macintosh OS X bundled with some Macintosh...
. To connect the camera to your computer and save files Turn on the camera and press [MENU]. On the “¥ SETTING” tab, select “USB” and then press [6]. Use [8] and [2] to select “Mass Storage”, and then press [SET]. Turn off the camera and then USB port use the USB cable that comes...
. To view copied images Double-click the camera’s drive icon. Double-click the “DCIM” folder to open it. Double-click the folder that contains the images you want to view. Double-click the image file you want to view. • For information about file names, see “Memory Folder Structure” on page 172. •...
. Movie Playback Precautions Proper movie playback may not be possible on some Macintosh models. If you experience problems, try the following. – Try recording movies with a quality setting of “STD”. – Upgrade to the latest version of QuickTime. –...
Page 168
IMPORTANT! • Recorded images are transferred over wireless LAN. Do not use the Eye-Fi card or turn off Eye-Fi card communication (page 175) when on an aircraft or in any other location where use of wireless communication is limited or prohibited. •...
Using a Smartphone to Play Back Images Stored on a FlashAir Card (FlashAir) Loading a commercially available FlashAir card in the camera makes it possible to view images on and copy them to a smartphone or computer over a wireless LAN connection.
Page 170
IMPORTANT! • When on an aircraft or in any other location where use of wireless communication is limited or prohibited, do not use a FlashAir card, or change the camera’s “FlashAir” setting (page 175) and the FlashAir card’s setting to those shown below. FlashAir: Off Memory Card: Start with the control image •...
Files and Folders The camera creates a file each time you shoot a snapshot, record a movie, or perform any other operation that stores data. Files are grouped by storing them in folders. Each file and folder has its own unique name. •...
File System (DCF). . About DCF The following operations are supported for DCF-compliant images. Note, however, that CASIO makes no performance guarantees concerning these operations. • Transferring this camera’s DCF-compliant images to another manufacturer’s camera and view them. • Printing this camera’s DCF-compliant images on another manufacturer’s printer.
. Supported Image Files • Image files shot with this camera • DCF-compliant image files This camera may not be able to display an image, even if it is DCF-compliant. When displaying an image recorded on another camera, it may take a long time for the image to appear on this camera’s monitor screen.
Other Settings (SETTING) This section explains menu items that you can use to configure settings and perform other operations in both the REC mode and PLAY mode. For information about menu operations, see page 106. Enabling Power Saving (ECO Mode) Procedure [MENU] * “¥...
Turning off Eye-Fi Card Communication (Eye-Fi) Procedure [MENU] * “¥ SETTING” Tab * Eye-Fi Select “Off” to disable Eye-Fi card communication (page 167). Configuring FlashAir Card Communication Settings (FlashAir) Procedure [MENU] * “¥ SETTING” Tab * FlashAir Selecting “Start with the control image” for the FlashAir card setting and selecting “On”...
Creating an Image Storage Folder (Create Folder) Procedure [MENU] * “¥ SETTING” Tab * Create Folder Creates a folder with a unique number (page 171). Files will be Create Folder stored in the new folder starting from when you record your next image.
Auto Image Orientation Detection and Rotation (Auto Rotate) Procedure [MENU] * “¥ SETTING” Tab * Auto Rotate Automatically rotates snapshots shot with the camera held vertically 90 degrees. Images not rotated automatically. The camera automatically detects whether a snapshot image was shot in portrait or landscape orientation and displays it accordingly.
Configuring Sleep State Settings (Sleep) Procedure [MENU] * “¥ SETTING” Tab * Sleep This feature turns off the monitor screen and lights the back lamp (green) whenever no camera operation is performed for a preset period of time. Press any button to turn the monitor screen back on.
Specifying the Operation when the Monitor Screen is Tilted (Screen Tilt) Procedure [MENU] * “¥ SETTING” Tab * Screen Tilt Power On Turns on the camera whenever the monitor screen is tilted. Turns on the camera whenever the monitor screen is tilted, and On/Off turns it off when the monitor screen is returned to its normal position.
Configuring World Time Settings (World Time) Procedure [MENU] * “¥ SETTING” Tab * World Time You can use the World Time screen to view the current time in a zone that is different from your Home City when you go on a trip, etc. World Time displays the current time in 162 cities in 32 time zones around the globe.
Setting the Camera’s Clock (Adjust) Procedure [MENU] * “¥ SETTING” Tab * Adjust When the date and time settings are what you want, select “Apply” and then press [SET] to apply them. [8] [2] Change the setting at the cursor location [4] [6] Move the cursor between settings •...
Specifying the Display Language (Language) Procedure [MENU] * “¥ SETTING” Tab * Language . Specify the display language you want. Select the bottom tab “¥”. Select “Language”. Select the language you want. • Camera models sold in certain geographic areas may not support display language selection.
Selecting the Screen Aspect Ratio and Video Output System (Video Output) Procedure [MENU] * “¥ SETTING” Tab * Video Output You can use the procedure in this section to select either NTSC or PAL as the video output system. You can also specify an aspect ratio of 4:3 or 16:9. NTSC Video system used in Japan, the U.S., and other countries Video system used in Europe and other areas 4:3 aspect ratio...
Formatting Built-in Memory or a Memory Card (Format) Procedure [MENU] * “¥ SETTING” Tab * Format If a memory card is loaded in the camera, this operation will format the memory card. It will format built-in memory if no memory card is loaded. •...
• The battery is intended for use with a CASIO Digital Camera only. Use with any other device creates the risk of the battery damage, or deterioration of battery performance and service life.
Page 186
DANGER • Failure to observe any of the following precautions creates the risk of battery overheating, fire, and explosion. – Never use or leave the battery near open flame. – Do not expose the battery to heat or fire. – Make sure the battery is oriented correctly when charging it. –...
Page 187
Also, remove the battery from the camera, taking care to protect yourself against burn injury. 3. Contact your retailer or nearest CASIO authorized service center. . Keep Away From Fire • Never expose the camera to fire, which can cause it to explode and creates the risk of fire and personal injury.
Page 188
Also, remove the battery from the camera, taking care to protect yourself against burn injury. 3. Contact your retailer or nearest CASIO authorized service center. . Disassembly and Modification • Never try to take the camera apart or modify it in any way. Doing so creates the risk of electric shock, burn injury, and other personal injury.
Also, remove the battery from the camera, taking care to protect yourself against burn injury. 3. Contact your retailer or nearest CASIO authorized service center. . Memory Cards • Memory cards are small and present a risk of accidentally being swallowed by infants and young children.
Page 190
CAUTION . Rechargeable Battery • If battery charging does not end normally within the specified charging time, stop charging anyway and contact your local CASIO authorized service center. Continued charging creates the risk of battery overheating, fire, and explosion. • Be sure to read the user documentation that comes with the camera and special charger unit before using or charging the battery.
CAUTION . Monitor Screen • Do not apply strong pressure to the LCD panel surface or subject it to strong impact. Doing so can cause the display panel glass to crack and lead to personal injury. • Should the monitor screen ever become cracked, never touch any of the liquid inside the monitor screen.
Page 192
CAUTION . Camera Jacket • When wearing the strap around your neck, the camera can unexpectedly bump into objects, fall, or become caught in a door, creating the risk of malfunction or personal injury. Hold the camera in your hand or take other precautions to avoid such problems. Never swing the jacket around by the strap.
Precautions During Use . Data Error Precautions Your digital camera is manufactured using precision digital components. Any of the following creates the risk of corruption of data in camera memory. – Removing the battery or memory card while the camera is performing some operation –...
. Lens • Never apply too much force when cleaning the surface of the lens. Doing so can scratch the lens surface and cause malfunction. • You may sometimes notice some distortion in certain types of images, such as a slight bend in lines that should be straight.
Page 195
Note that CASIO COMPUTER CO., LTD. shall not be held liable for use of this product in any way that infringes on the copyrights of others or that violates copyright laws.
If problems persist after you perform the above steps or if the battery fails to charge after 5 hours, it could mean that the battery is faulty. Contact your nearest CASIO authorized service center. Appendix...
Battery Precautions . Precautions during Use • Operation provided by a battery under cold conditions is always less than operation under normal temperatures. This is due to the characteristics of the battery, not the camera. • Charge the battery in an area where the temperature is within the range of 15°C to 35°C (59°F to 95°F).
Using a Memory Card See page 29 for information about supported memory cards and how to load a memory card. . Using a Memory Card • SD memory cards, SDHC memory cards, and SDXC memory cards have a write protect switch. Use the Write enabled switch when you need to guard against accidentally deleting data.
Reset Initial Default Settings The tables in this section show the initial default settings that are configured for menu items (displayed when you press [MENU]) after you reset the camera (page 184). Menu items depend on whether the camera is in the REC mode or PLAY mode. •...
Page 200
. p PLAY MENU Images: DPOF Printing – All images / Protect – Slideshow Time: 30 min / Date/Time – Interval: 3 sec / Effect: Pattern 1 Rotation – MOTION PRINT Create Resize – Movie Editing – Trimming – Movie Merge –...
2)The battery may be dead. Charge the battery (page 23). If the battery goes dead soon after being charged, it means the battery has reached the end of its life and needs to be replaced. Purchase a separately available CASIO NP-130A or NP-130 rechargeable lithium ion battery. The camera 1)Auto Power Off may have activated (page 178).
Page 202
(page 55) or select a different BEST SHOT scene (page 83). The red ? (Flash The flash unit may be malfunctioning. Contact a CASIO Off) icon is authorized service center or your original retailer. Note that...
Page 203
Problem Possible Cause and Recommended Action A recorded image 1)Camera power may have been turned off before the save was not saved. operation was complete, which will result in the image not being saved. If the battery indicator shows , charge the battery as soon as possible (page 27).
Page 204
Problem Possible Cause and Recommended Action Playback The color of the Sunlight or light from another source may be shining directly playback image is into the lens when you are shooting. Position the camera so different from what sunlight does not shine directly into the lens. appears on the monitor screen when shooting.
Page 205
If the same message appears after you turn power back on, contact your retailer or a CASIO authorized service center. There are various The monitor screen shows indicators and other information indicators and about shooting conditions and the image you are recording.
The Anti Shake unit of the camera may be malfunctioning. LENS ERROR 2 If the same message appears after you turn power back on, contact your retailer or a CASIO authorized service center. Load paper! The printer ran out of paper while printing.
Page 207
Your camera system is corrupted. Contact your retailer or a SYSTEM ERROR CASIO authorized service center. The LOCK switch of the SD, SDHC, or SDXC LOCK memory card loaded in the camera is in the The card is locked.
Number of Snapshots/Movie Recording Time Snapshot Built-in Memory SD Memory Card Image Size Quality File Size Recording Recording (Pixels) Capacity Capacity Fine 10.71 MB 1072 (4608 3456) Normal 5.57 MB 1654 Fine 9.43 MB 1214 (4608 3072) Normal 4.92 MB 1873 16:9 Fine...
Page 209
Movies Maximum Built-in Continuous Image Size/ Recording File Size of Approximate Data Maximum Memory Recording Pixels Time with 1-minute Rate (Frame Rate) File Size Recording Time per (Audio) SD Memory Movie Capacity Movie Card 14.2 Megabits/ 2 hours (1920 1080) second 25 seconds 106.5 MB...
Page 210
YouTube Maximum Built-in Continuous Image Quality Recording Approximate Data Maximum Memory Recording (Pixels) / Time with Rate (Frame Rate) File Size Time per Recording (Audio) SD Memory Movie Capacity Card YouTube (FHD) 14.2 Megabits/second 2 hours 25 seconds 15 minutes (1920 1080) (30 frames/second)
Page 211
Values when shooting with “ART SHOT”. • Snapshot and movie recording capacity values are approximate and intended for reference only. Actual capacity depends on image contents. • File size and data rate values are approximate and intended for reference only. Actual values depend on the type of image being shot.
Specifications File Format Snapshots: RAW (DNG)*, JPEG (Exif Version 2.3; DCF 2.0 standard; DPOF compliant) Movies: MOV format, H.264/AVC standard, IMA-ADPCM (stereo) * DNG file format is one type of RAW image file, and it is recommended by Adobe Systems Incorporated for use as a standard image file format.
Page 213
Exposure Control Program AE, Aperture Priority AE, Shutter Speed Priority AE, Manual Exposure Exposure –2.0 EV to +2.0 EV (in 1/3EV steps) Compensation Shutter CMOS electronic shutter, mechanical shutter Shutter Speed Snapshot (Program Auto): 1/4 to 1/2000 second Snapshot (Premium Auto PRO): 4 to 1/4000 second Snapshot (Aperture Priority AE): 1 to 1/2000 second Snapshot (Shutter Speed Priority AE): 15 to 1/2000 second Snapshot (Manual Exposure): 15 to 1/2000 second...
Page 214
• Battery: NP-130A (Rated Capacity: 1800 mAh) • Recording Medium: 16GB SDHC memory card (SanDisk Corporation) In accordance with CIPA (Camera and Imaging Products Association) standards In accordance with CASIO standards Other settings Time Lapse scene: Standard, Recording interval: 1/2 seconds, Total time: Off,...
Page 215
The power cord set is not supplied. The power cord used must comply with relevant national and/or international standards. Declaration of Conformity According to EU Directive Manufacturer: CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Responsible within the European Union: CASIO EUROPE GmbH Casio-Platz 1, 22848 Norderstedt, Germany Appendix...
Page 216
CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan MA1308-A 2013...