Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Related Manuals for Casio EXILIM EX-ZR310
Summary of Contents for Casio EXILIM EX-ZR310
- Page 1 Adjustment Manual Model: EX-ZR300 EX-ZR310 EX-ZR400 EX-ZR410 EX-ZR500 EX-ZR510 EX-ZR1000 EX-ZR1200 EX-ZR1500...
-
Page 2: Adjustment Item
EX-ZR300 Ver. 1 Date 3/Jul/2012 EX-ZR300 ADJUSTMENT „ Overview „ 1. Adjustment Item After the main PCB or lens unit have been replaced, perform the adjustments shown below. Adjustment OPT CENTER/ Item Writing The SHADING/WB1/WB2/ ZOOM FOCUS Replaced Lens Code ISO/SHUTTER/ Part CCD DEFECTS... -
Page 3: Camera Settings
EX-ZR300 3. Camera Settings Set the Sleep mode to "OFF", and then launch the TEST MODE. (Avoid LCD being turned off during the adjustment as the result of the Sleep mode activation.) <Procedure> (1) Turn the camera on while holding down the [MOVIE] and the [UP]. (2) Press the [DOWN] twice, press the [UP] and then press the [MENU]. - Page 4 EX-ZR300 „ Writing The Lens Code „ 1. Purpose To adjust the settings of the Image Stabilization Unit. 2. Overview The three sets of code numbers (each three-digit number) on the lens unit are taken and written into the ADJ area. NOTE: Be sure to do this before going to the other adjustments.
- Page 5 EX-ZR300 „ Save the USB drivers „ Procedure * The procedures are described with Windows XP. (1) Prepare the following USB drivers. • uusbd.inf • uusbd.sys (2) Save [ uusbd.inf ] on the "\WINDOWS\inf". (3) Save [ uusbd.sys ] on the "\WINDOWS\system32\drivers". * The drivers are only available for Windows.
- Page 6 EX-ZR300 „ Zoom Adjustments „ (1) Launch the TEST MODE. (See "Camera Settings" on page 1.) (2) Select and run "3: LENS" → "7: ZOOM". (3) When "ZOOM START?" appears, press the [SET]. (4) Press the [shutter] button. When "ADJ OK" appears, zoom adjustment is completed. –...
-
Page 7: Adjustment Procedures
EX-ZR300 „ OPT CENTER/SHADING/WB1/WB2/ISO/SHUTTER/CCD DEFECT Adjustments „ (Adjustments for discrepancies between individual cameras) 1. Target Requirements Light source requirements Required Luminance 1: 0 ± 10 cd Equivalent * The requirements to the left luminance are fixed conditions for the Luminance 2: 600 ±... -
Page 8: Block Diagram
EX-ZR300 (22) Select and run "4: PICTURE" → "11: ISO". (23) When "ISO ADJ START" appears, press the [SET]. (24) Set the camera to the luminance box and press the [shutter] button. (25) When "ADJ OK" appears, ISO adjustment is complete. (26) Turn the camera off and then on again. - Page 9 EX-ZR300 „ Focus Adjustment (Adjustment for discrepancies between individual cameras) „ 1. Adjustment And Checking Procedure Focus adjustments • Perform "Focus adjustment [A] – Adjustment at infinity". • Perform "Focus adjustment [B] – Adjustment at MACRO". • Perform "Focus adjustment [C] – Adjustment at SUPER MACRO". NOTE: Adjustments must be performed in the sequence: [A] →...
- Page 10 EX-ZR300 4. Block Diagram Focus adjustment [A] [Adjustment at infinity] Focus adjustment [B] [Adjustment at MACRO] Chart surface Distance from the front end of the lens ring to the chart surface 900 ± 5 mm Auto collimator Light source Focus adjustment [C] [Adjustment at SUPER MACRO] Chart surface Distance from the front end of the lens ring to the chart surface...