Crosley BRT18S6GW0 Owner's Care & Use Manual

TO BE REMOVED BYTHE CUSTOMER AFTER iNSTALLATiON iS COMPLETE
f
[] iNSTALLATiON CHECKOFF LIST
Doors
[] Handles are secure and tight
[] Door seals completely to cabinet on all sides
[] Freezer door is level across the top
Leveming
[] Refrigerator is level, side to side and tilted 1/4" (6ram) front to back
[] Toe grille is property attached to refrigerator
[] Cabinet is setting solid on all corners
Emectrica[ Power
[] House power turned on
[] Refrigerator plugged in
lee Maker
[] House water supply connected to refrigerator
[] No water leaks present at all connections - recheck in 24 hours
[] be Maker is turned ON.
FinamChecks
[] Shipping material removed
[] Fresh Food and Freezer controls set
[] Crisper Humidity controls set
[] Registration Card sent in
J
ToolsNecessary:
Phillips he(_d
@uodrex heod Socket Adjustc/ble
sorewddt/er VWench Set Wrench
HAND TRUCKING
,, Load refrigerator from side of cabinet only,
_, Do not run retaining straps over handbs.
_, Do not over-tighten retaining straps.
,, Never use refrigerator handles to move the
refrigerator=
_, Remove tape from doors only after unit is in
place=
SHiPPiNG MATERIAL
2 PIECES OF TAPE --
1 SHELF SPACER--
TOE GRULLE
2 PUECES OF FOAM
AND rAPE
2 PmECES OF TAPE
1 PUECEOFTAPE
2 PmECES OF TAPE _
4 PIECES OF rAPE
2 PIECES OF TAPE .....
2 PIECES OF FOAM
1 PIECE OF TAPE
.... 1 PUECE OF "TAPE
2 PIECES OF TAPE
2 PUECE5 OF TAPE
Remove Shipping material, (Features may vary per model,)
J
WATER SUPPLY
Connect water supply - check for water
baks, Turn icemaker OFF if water supply
is not connected immediateJyo
Connecting to a reverse osmosis system
is not recommended.
/Hnclude enough tubing in loop to aUlow
moving refrigerator out for cba_ing.)
J
iNSTALLATiON CLEARANCES
Allow the following clearances for ease of installation, proper air circulation, and
plumbing and electrical connections:
,, Sides & Top.......... 3/8"
,, Back ....................... 1"
LEVEUNG AND ADJUSTING
All four corners of your refrigerator must rest firmly on a solid floor. Your refrigerator
is equipped with adjustable front rollers or front leveling screws to help level your
unit.
To [eve[ cabinet or change door height:
1, Remove toe grille,
2, Use fiat-blade screwdriver or 3/8" socket wrench to adjust front rollers. Use
adjustable wrench to adjust bveling screws.
Toe Grille
Adjustable Front Roller
(some models)
Stationary Front Roller
with Leveling Screw
(some models)
f
When changing controls, wait 24
hours before making additiona!
adjustments.
Humidity Control
\
Ensure icemaker is turned ON.
Signal Arm
DOOR REMOVAL (IFNECESSARY)
if you need to remove the doors to get your refrigerator into the house please see
"Door Removal and Reversal instructions" in your Use & Care Manual
........ J D0_r
See "Normal Operating Sights & Sounds" in the Use & Care Manua/
so you understand the sounds you may hear once your refrigerator is
running=
Please read entire Use & Care Manua/to become aware of important
safety instructions and to become familiar witrh your new refrigerator=
Send in Registration card to register your refrigerator.
Congratulations! You are ready to enjoy your new refrigerator.