Frigidaire GLTF2070DS0 Installation Instructions page 5

Cable
Tie
2.
4.
5.
6.
INSTALLATION
Run some water from the hot
and cold faucets to flush the
water lines and remove
particles that might clog up the
water valve screens.
Remove the inlet hoses and
rubber washers from the
plastic bag and install the
rubber washers in each end
of the inlet hoses.
Carefully connect the inlet hose
(90 ° elbow end) marked "HOT"
to the outside "H" outlet of the
water valve. Tighten by hand, then
tighten another 2/3 turn with
pliers. Carefully connect the other
inlet hose (90 ° elbow end) to the
inside "C" outlet of the water valve.
Tighten by hand, then tighten
another 2/3 turn with pliers. Do
not crossthread or over-
tighten
these connections.
Connect the inlet hose ends to the HOT and COLD water
faucets tightly by hand, then tighten another 2/3 turn with
pliers. Turn the water on and check for leaks.
NOTE: Use only new hoses.
Carefully move the washer to its final location.
NOTE: Do not use the dispenser drawer or door to lift
washer.
With the washer in its final position, place a level on top of
the washer, no rocking of the washer should exist. Adjust the
front leveling legs up or down to ensure the washer is resting
solid. Rear leg adjustment is accessible through the front
service panel. Turn the lock nuts on each leg up towards the
base of the washer and snug with a wrench.
NOTE: Keep the leg extension at a minimum to prevent
excessive vibration. The farther out the legs are
extended the more the washer will vibrate.
Form a U shape on the end of the drain hose with the hose
pointed toward the drain. Place in a laundry tub or standpipe
and secure with the cable tie provided in the enclosure
package.
NOTE: If the drain hose is placed in a standpipe without
forming a U shape, a siphoning action could occur.
There must be an air gap around the drain hose. A
snug hose fit can also cause a siphoning action.
Cable Tie
Cable
Tie
Cable
Tie
8. Plug the power cord into a grounded outlet.
NOTE: Check to ensure the power is off at a circuit
breaker/fuse box before plugging the power
cord into an outlet.
9. Turn on the power at a circuit breaker/fuse box.
10. Read the Operating instructions and Owner's Guide
provided with the washer. They contain valuable
and helpful information that will save you time and
money.
11. Run the washer through a complete cycle. Check for water
leaks and proper operation.
12. If your washer does not operate, please review the
"Avoid Service Checklist" in your Owner's Guide before
calling for service.
13. Place these instructions in a location near the washer
for future reference.
NOTE: A wiring diagram and technical data sheet are located in
an envelope attached to the left hand side panel on the
inside of the washer.
REPLACEMENT PARTS
If replacements parts are needed for your washer,
contact the source where you purchased your
washer, call 1-800-944-9044, or visit our website,
www.frigidaire.com, for the Frigidaire Company
Authorized Parts Distributor nearest you.
r:''i'lzl_l_'li_L_ Destroy the carton and plastic bags
after the washer is unpacked. Children might use them
for play. Cartons covered with rugs, bedspreads, or
plastic sheets can become airtight chambers causing
suffocation. Place all materials in a garbage container
or make materials inaccessible to children.
_The instructions in this manual and all
other literature included with this washer are not meant to
cover every possible condition and situation that may occur.
Good safe practice and caution MUST be applied when
installing, operating and maintaining any appliance.
Maximum benefits and enjoyment are achieved
when all the Safety and Operating instructions are
understood and practiced as a routine with your
laundering tasks.