Frigidaire SGGR341AS0 Installation Instructions Manual
Frigidaire SGGR341AS0 Installation Instructions Manual

Frigidaire SGGR341AS0 Installation Instructions Manual

Gas & electric dryer

Advertisement

Quick Links

Installation
Instructions
Gas & Electric
Dryer
Before beginning
installation,
carefully read these instructions.
This will simplify the installation
and ensure the dryer
is installed correctly and safely. Leave these instructions
near the Dryer after installation
for future reference.
NOTE: The electrical service to the Dryer must conform
with local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70 or in Canada, CSA C22.1 Canadian Electrical Code Part 1.
NOTE: The gas service to the Dryer must conform
with local codes and ordinances
and the latest edition
of the
National Fuel Gas Code ANSI Z223.1 or in Canada, CAN/CGA B149.12.
NOTE: The Dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 (latest editions) for HOME USE only.
This Dryer is not recommended
for commercial
applications
such as restaurants or beauty salons, etc.
For your safety the information
in
this manual must be followed
to minimize
the risk
of fire or explosion
or to prevent property damage,
personal
injury or loss of life.
- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any other
appliance.
- WHATTO
DO IFYOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electrical
switch; do not use
any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately
call your gas supplier from a
neighbor's
phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the
fire department.
Installation
and service
must be performed
by a
qualified
installer,
service
agency
or the gas
supplier.
Contents
SUBJECT
Prednstallation Requirements
Electrical Requirements
Exhaust System Requirements
Gas Supply Requirements
Location of Your Dryer
Mobile Home Installation
Rough-In Dimensions
Unpacking
Reversing Door Swing
Electrical Installation
Grounding Requirements
Electrical Connections--3-wire
Electrical Connections--4-wire
Installation
Replacement Parts
PAGE
2
2
2-3
3
4
5
5-6
6
6
7
7
8
8
9
9
Printed in U.S.A.
P/N 131751700 (9806)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SGGR341AS0 and is the answer not in the manual?

Questions and answers

Summary of Contents for Frigidaire SGGR341AS0

  • Page 1 Installation Instructions Gas & Electric Dryer Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the dryer is installed correctly and safely. Leave these instructions near the Dryer after installation for future reference. NOTE: The electrical service to the Dryer must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/NFPA 70 or in Canada, CSA C22.1 Canadian Electrical Code Part 1.
  • Page 2: Electrical Requirements

    POWERSUPPLYCORD - The dryer is equipped with a 120 volt PRE-INSTALLATION REQUIREMENTS 3-wire power cord. Tools and Materials Required for Installation: 1. Phillips head screwdriver. NOTE: Do not under its', ,:._ _IL any circumstances 2. Channel-lock adjustable pliers. 3. Carpenter's level. prong from plug.
  • Page 3: Gas Supply Requirements

    Venting vertical through a roof may expose the exhaust MAXIMUM LENGTH system to down drafts causing an increase in vent of 4" (10.2 cm) Dia. Rigid Metal Duct restriction. Running the exhaust system through an uninsulated area VENT HOOD TYPE may cause condensation and faster accumulation of lint.
  • Page 4 4. A minimum of 120 square inches (774.2 square cm) of LOCATION OF YOUR DRYER opening, equally divided at the top and bottom of the door, DO NOT INSTALL YOUR DRYER: is required. Air openings are required to be unobstructed 1.
  • Page 5: Mobile Home Installation

    MOBILE HOME INSTALLATION UNDER COUNTER & STACK MODELS ROUGH-IN DIMENSIONS 1. Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 inches (10.16 cm) in 26 7/8" diameter with no obstructions.
  • Page 6: Unpacking

    UNPACKING TOP CONSOLE MODELS 1. Using the four shipping carton corner posts (two on each ROUGH-IN DIMENSIONS side), carefully lay the dryer on its left side and remove foam shipping base. 26 7/8' prevent damage, do not usethe control panel as a means to pick up or move the dryer.
  • Page 7: Electrical Installation

    ELECTRICAL INSTALLATION For a permanently connected dryer: 1. The dryer MUST be connected to a grounded metal, permanent wiring system; or an equipment grounding ALL ELECTRIC Dryers conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on The following are specific requirements for the appliance.
  • Page 8 GREEN POWER CORD GREEN GREEN GROUND WIRE SILVER TERMINAL GROUND SCREW SILVER TERMINAL SCREW TERMINAL BLOCK GREEN NEUTRAL GROUND WIRE GREEN BLACK TIGHTEN GROUND _/HITE TO THESE WIRE THREADS TIGHTEN NUT TO THESE RED" THREADS RELIEF MOUNTING BRACKET • POWER STRAIN _ CORD STRAIN...
  • Page 9: Installation

    INSTALLATION REPLACEMENT PARTS 1. GAS CONNECTION (Gas dryers only) a. Remove the shipping cap from gas pipe at the rear of If replacement parts are needed for your dryer, contact the the dryer. source where you purchased your dryer. NOTE: DO NOT connect the dryer to L.P.gas service without converting the gas valve.

This manual is also suitable for:

Sger341as0

Table of Contents