GE Monogram ZDIC150 Installation Instructions Manual
Automatic icemaker
Hide thumbs
Also See for Monogram ZDIC150:
- Owner's manual (16 pages) ,
- Owner's manual (16 pages) ,
- Owner's manual (16 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for GE Monogram ZDIC150
Summary of Contents for GE Monogram ZDIC150
- Page 1 Installation I struct" Automatic Icemaker ZDIC150 ZDIS1S0 Design Guide With Instollotion Instructions monogram.com...
-
Page 2: Table Of Contents
Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner's Manual for warranty information. • Use this appliance only for its intended purpose. -
Page 3: Design Information
Custom Panel Installation Top View *For flush installation of ZDIS150 and ZDIC150 models: Install a !/2"-wide filler strip on the hinge side. The filler strip will act as a spacer between the door case and adjacent cabinets and will prevent interference with the cabinet door swing. Recess the filler strip !"... -
Page 4: Optional Accessories
13/4" panel. See installation instructions on pages 10 and 11. TOOLS AND MATERIALS REQUIRED • 1/4" socket • 3/4" adjustable wrench Level GE SmartConnect Refrigerator Tubing Kit or 1/4" O.D. copper tubing, of sufficient length to reach the installation... -
Page 5: Advance Planning
Installation Instructions ADVANCE PLANNING ADVANCE PLANNING (cont.) CAUTION: Due to excessive weight, Before you begin: TWO PEOPLE ARE REQUIRED TO MOVE AND 1. If a custom panel is to be installed, follow INSTALL THIS ICEMAKER. Failure to do so can the instructions shown on pages 10 and 11. -
Page 6: Power Supply
Installation Instructions POWER SUPPLY REMOVE PACKAGING AND PARTS WARNING: (Please read carefu,y . • Lag the carton on rear face and break open the bottom FOR PERSONAL SAFETY, THIS APPLIANCE MUST flap. BE PROPERLY GROUNDED. Failure to followthese • Set the carton upright instructions c an result indeath,fire or electrical shock. -
Page 7: Watersupply
NOTE: The only GEapproved plastic tubing is supplied in the GE SmartConnecf MRefrigerator Tubing kits. Do CONNECT DRAIN not use ang other plastic water supplg line because the line is under pressure at all times. Other tgpes of plastic... -
Page 8: Connect Water Supply
Line to Icemaker Remove the door (all models}: • Remove the hinge pin from the top hinge. GE SmartConnect'" Tubing: • Insert the molded end of the tubing into the • Lift the door off of the bottom hinge. Place the icemaker connection. - Page 9 Installation Instructions REVERSE THE DOOR SWING {cont.} REVERSE THE DOOR SWING {cont.} Reinstall the door (all models} (cont.}: Reverse the hinges (all models}: • Remove the screws opposite the door hinges, TopHinge top and bottom. Set aside. • Remove the two screws holding top hinge. •...
- Page 10 Installation Instructions for ZIP75BB Kit • BEFORE YOU BEGIN: NOTE: If installing a 3/4" trimless custom panel, a 1-1/2" wide filler strip mag be required. The filler Read these instructions completely and carefully. strip will act as a spacer between the icemaker •...
- Page 11 Installation Instructions for ZIP75BB Kit STEP 2 DISCONNECT POWER STEP5 SECURE SIDE TRIM PIECES TO THE ICE MACHINE TO CUSTOM PANEL • Lay the custom panel appearance-side-down on a clean surface. REMOVE HANDLE STEP 2 • Align top and bottom side trim to the custom AND NAMEPLATE panel sides.
- Page 12 For Monogram ® local service in _lour area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Consumer & Industrial Pub.No. 31-46199-2 Appliances PartNo. 224D188gP001...