GE PGP953 Installation Instructions Manual

30" sealed gas cooktop
Table of Contents

Advertisement

Available languages

Available languages

I stallatio
I struction
30" SealedGasCooktop
PGP953, PGP959, CGP350
i r_l
ouestions? call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
i
IN THE COMMONWEALTH
OF
MASSACH USETTS:
, This product
must be installed by a licensed
plumber
or gas fitter.
. When using ball-type
gas shut-off valves, they
shall be the T-handle type.
. A flexible gas connector,
when used, must not
exceed 3 feet.
BEFORE YOU BEGIN
Read these instructions
completely
and carefully.
.IMPORTANT
- Save these
instructions
for local inspector's
use.
" IMPORTANT
- Observe all governing
codes and ordinances.
, Note to Installer-
Be sure to leave these
instructions
with the Consumer.
Note to Consumer
- Keep these instructions
for
future reference.
, Product failure due to improper
installation
is not
covered under the Warranty.
AWARNING
- Thisappliancemust be
properly grounded.
.
IMPORTANT
- Leak testing ofthe
appliance
shall be conducted
according
to the
manufacturer's
instructions.
, Proper installation
is the responsibility
of the
installer and product failure due to improper
installation
is NOT covered under warranty.
WARN ING - Disconnect
all electrical
power at the main circuit breaker or fuse box
before installing.
FOR YOUR SAFETY:
WARNING
- Iftheinformation
in this manual
is not followed
exactly,
a fire,
explosion
or gas leak may result causing
property
damage,
personal
injury or death.
Do not store or use gasoline
or other flammable
vapors and liquids
in the vicinity
of this or any
other appliance!
Do not install this product
with air curtain
hood
or other range hood that blows air down on the
cooktop.
Airflow
may interfere
with operation
of
gas burners
resulting
in fire or explosion
hazard,
WHAT
TO DO IFYOU SMELL
GAS:
Do not try to light any appliance.
Do not touch
any electrical
switch;
do not use any phone in
your building.
Immediately
call your gas supplier
from a
neighbor's
phone. Follow the gas supplier's
instructions.
, If you cannot
reach your gas supplier,
call the
fire department.
Installation
and service must be performed
by
a qualified
installer,
service agency or the gas
supplier,
This cooktop
has been certified
by UL. You'll find
safety precautions
in your Owner's Manual.
Read them carefully.
Installation
of this cooktop
must conform
with
local codes or in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.Z/NFPA
54-Latest
edition.
Be sure your cooktop
is installed properly
by a
qualified
installer or service technician.
To eliminate
reaching over surface burners,
cabinet storage above burner should be avoided.
Do not install the unit near an outside door or
where a draft may affect its use.
31-10858-1
(08-12GE)
1

Advertisement

Table of Contents
loading

Summary of Contents for GE PGP953

  • Page 1 30" SealedGasCooktop I struction PGP953, PGP959, CGP350 In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca i r_l ouestions? call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com FOR YOUR SAFETY: IN THE COMMONWEALTH MASSACH USETTS: WARNING - Iftheinformation...
  • Page 2: Installation

    Installation Instructions IMPORTANT SAFETY INSTRUCTIONS PARTS INCLUDED ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having 2 Screws Regulator amperage as noted on the rating plate.
  • Page 3: Pre-Installation

    Installation Instructions PRE-INSTALLATION CHECKLIST Remove Installation Instructions from When preparing cooktop opening, make sure the inside of the cabinet and the literature pack and read them carefully cooktop do not interfere with each other. before you begin. (See section on preparing the opening.) Be sure to place all literature (Owner's Manual,...
  • Page 4: Preparing The Opening

    MAKE SURE WALL COVERINGS, side wall 30" or wider COUNTERTOP AND CABINETS cabinet base 2-1/2" MIN from cutout to front of counterto u AROUND COOKTOP CAN WITHSTAND HEAT (UP TO 200°F) PGP953 6" 2-i/4" 3-3/4" GENERATED BY COOKTOP PGP959 12" 12" 2-718" CGP350 12"...
  • Page 5: Installing The Cooktop Unit

    Installation Instructions iNSTALLiNG THE COOKTOP UNiT LOCATE ELECTRICAL OUTLET AND [][] ATTACH BRACKETS TO COOKTOP GAS SHUT-OFF VALVE BENEATH Remove the screw from the side of the cooktop CABINET and screw the hold-down bracket to the side of the cooktop unit.
  • Page 6 Installation Instructions INSTALLATION--GAS CONNECTIONS PROVIDE ADEQUATE GAS SUPPLY r3] INSTALL REGULATOR ONTO BURNER BOX BOTTOM This cooktop is designed to operate on natural gas at 5" of water column manifold pressure and Screw the regulator 7" of water column (W.C.) supply pressure. It is onto the burner shipped from the factory set for natural gas.
  • Page 7: Installation Instructions

    Installation Instructions CHECK FOR LEAKS INSTALLATION OVER BUILT-IN OVEN LEAK TESTING OF THE APPLIANCE SHALL BE CONDUCTED ACCORDING TO THE MANUFACTURER'S See built-in oven installation for complete INSTRUCTIONS. installation instructions. Before testing for leaks, make sure all burner knobs are in the OFF position. After connecting the cooktop to gas, check system for leaks with o manometer.
  • Page 8 Installation Instructions INSTALLATION--ELECTRICAL CONNECTIONS , WARNING - Disconnect all electrical power at the main circuit breaker or fuse box before installing. ELECTRICAL SUPPLY AND OUTLET An adequate electrical supply and outlet must be used to operate the electrical parts of your cooktop.
  • Page 9: Cooktop Burners

    Installation Instructions COOKTOP BURNERS E_ ASSEMBLING THE COOKTOP BURNERS The electrode of the igniter is exposed. Be careful not to turn on any cooktop controls while the top of the burner is removed. Do not remove the top or touch the electrode of any burner while another burner is turned on.
  • Page 10: Burner Grates

    Installation Instructions COOKTOP BURNERS (CONT.) BURNER IGNITION BURNER GRATES The three cooktop grates are designed for specific Cooktop Spark Ignition-When you turn the positions. For maximum stability, these grates cooktop knob to LITE, the spark igniter makes a should only be used in their proper position with series of electric sparks (ticking sounds) which light the edges positioned on top of the black bumpers...
  • Page 11: Operation Checklist

    Installation Instructions OPERATION CHECKLIST When ordering parts, always include the serial Moke sure all controls ore left in the OFF position. Check to be sure the cooktop is in the number, model number and a code letter to UNLOCKED position (on models so equipped). ensure proper replacement parts.
  • Page 12: Making The Lp Conversion

    Installation Instructions MAKING THE LP CONVERSION TOOLS YOU WILL NEED SAFETY INFORMATION FOR LP CONVERSION SHOULD KNOW The pressure regulator and burner orifices are set 7mm Nutdriver for natural gas. To use LP gas, the regulator burner orifices must be converted. The LP orifice Safety Glosses spuds for the cooktop...
  • Page 13 Locate the LP orifices attached to the regulator CENTER BURNER along with separate LP conversion instructions. 15,000 BTU/hr Extra Large Burner (PGP953 Models) They will have a digit for size and a letter for type of gas, on the top or side. (IMPORTANT: Save the orifices removed from the appliance for future use.)
  • Page 14 Installation Instructions CHANGE COOKTOP BURNER CHANGE COOKTOP BURNER ORIFICES (CONT.) ORIFICES (CONT.) CENTER BURNER LEFT FRONT BURNER 20,000 BTU/hr Tri-Ring Burner (PGP959 and CGP350 (PGP959 and CGP350 Models) Models) Griddle Screw spuds located through these The griddle screw is marked with N openings.
  • Page 15 Installation Instructions MAKING THE LP CONVERSION (CONT.) ADJUST BURNER FLAMES Testing Flame Stability: Test 1 - Temporarily replace knobs. Turn the Turn all burners full on and check the flames. knob from "HI" to the lowest setting They should be blue in color with some yellow quickly.
  • Page 16 Notes.
  • Page 17 I struction Ta le de cuJsson scell d'i stallat" au gaz de 76 cm (30") PGP953, PGP959, CGP350 Web 8 I'adresse : www.electromenagersge.ca POUR VOTRE Si_CURITI_ AVANT DE COMMENCER Avant de commencer, lisez attentivement la totalit6 AAVERTISSEMENT - de ces instructions.
  • Page 18: Instructions D'installation

    Instructions d'installation INSTRUCTIONS IMPORTANTES DE SI CURITI PII_CES COMPRISES Cette table de cuisson a 6t6 homologu6e UL Vous trouverez des pr6cautions 6 prendre en mati6re de s6curit6 dans votre Guide d'utilisation et de soins. Lisez-les attentivement. , L'installation de votre table de cuisson dolt se conformer aux codes Iocaux ou, en I'absence de 2vis...
  • Page 19 Instructions d'installation DE VITRIFICATION AVANT INSTALLATION LISTE Enlevez les instructions d'installation de la Pour pr6parer I'ouverture de la surface de trousse de documentation et lisez-les cuisson, vous devez vous assurer que I'int6rieur de I'armoire ne touche pas la table soigneusement avant de commencer.
  • Page 20 76,2 cm 150") 2-2/2" MIN. Entre I'ouverture ou supeneur ASSUREZ-VOUS OUE LES REV['TEMENTS et le devont du comptoir MUR, LE COMPTOIR ET LES ARMOIRES AUTOUR DE LA TABLE DE CUISSON PGP953 9,5cm(3-3/4") Z5,2 cm (6") 5,7cm(2-Z/4") PUISSENT SUPPORTER LA CHALEUR PGP959 30,5cm(12") 30,5cm(12")
  • Page 21: Montage

    Instructions d'instollotion NSTALLATION LA UNITE DE LA TABLE DE CUISSON PLACEZ LA PRISE D'ALIMENTATION FIXEZ LES SUPPORTS DE FIXATION I_LECTRIQUE ET LE ROBINET A LA TABLE DE CUISSON D'ALIMENTATION DE GAZ Enlevez la vis d'un c6t6 de la table de cuisson, vissez AU-DESSOUS DE L'ARMOIRE un support de fixation 6 un c6t6 de la table de...
  • Page 22 Instructions d'installation INSTALLATION--BRANCHEMENT DU GAZ FOURNISSEZ UN BON [31 INSTALLEZ LE REGULATEUR EN APPROVISIONNEMENT EN GAZ BAS DE LA BO'[TE DE BRULEURS Cette table de cuisson est conque pour fonctionner Vissez le r6gulateur dans gaz naturel 6 une pression de tubulure d'admission le raccord du bas de de 4 po.
  • Page 23 Instructions d'installation r57 VERIFIEZ QU'IL N'Y A PAS DE INSTALLATION SUR UN FOUR FUITE ENCASTRE LA VITRIFICATIONDE FUITES SUR L'APPAREIL DOlT Consultez I'installation du four encastr6 pour y I_TREEFFECTUCEEN CONFORMITI_ AVEC LES trouver les instructions d'installation. INSTRUCTIONS DU FABRICANT. Avant de v6rifier qu'il n'y a pas de fuite, assurez- vous que tous les boutons de brQleurs soient en position OFF (arr_t).
  • Page 24 Instructions d'installation INSTALLATION--RACCORDS ELECTRIQUES AVERTISSEMENT - D6branchez tout courant 61ectrique a u niveaudu disjoncteur d e la maison ou de la boTte 5 fusibles a vant d'installer. ALIMENTATION ELECTRIQUE ET PRISE Vous devez utiliser une bonne alimentation 61ectrique et une bonne prise pour faire fonctionner les 616ments 61ectriques de votre table de cuisson.
  • Page 25 Instructions d'installation BROLEURS DE LA TABLE DE CUISSON ASSEMBLEZ LES BRULEURS DE LA TABLE DE CUISSON L'61ectrode de I'allumeur est expos6e. Veillez 5 n'allumer aucun contr61e de la table de cuisson Iorsque le dessus du brOleur est enlev6. N'enlevezjamais le haut d'un brOleur ou son 61ectrode quand un autre brOleur est allure6.
  • Page 26 Instructions d'installation ALLUMAGE DES BRULEURS LES FLAMMES DU BRULEUR Allumage de la table de cuisson- Quand vous Allumez chaque brOleur. Les flammes doivent @tre mettez le bouton de la table de cuisson en position bleu sans trace de jaune. Les flammes du brQleur LITE (allumage), I'allumeur fait une s6rie d'6tincelles ne doivent pas scintiller ou s'6carter du br01eur.
  • Page 27 Instructions d'installation LISTE DE V(--RIFICATION DE FONCTIONNEMENT Assurez-vous que tousles contr61es restent en q)uand vous commandez des pi6ces, indiquez position OFF (arr#t). V#rifiez que la table toujours le num@o de s6rie, le num@o de de cuisson soit en position UNLOCKED module et les lettres de code pour obtenir les (d#verrouill#e) (sur les modules ainsi #quip#s).
  • Page 28 Instructions d'installation CONVERSION AU GAZ PROPANE (LP) RENSEIGNEMENTS RELATIFS A LA AJUSTEZ VOTRE PLAQUE DE CUISSON #, UN USAGE AU GAZ LP SE_CURITEE Q UE VOUS DEVEZ CONNA'[TRE D6bronchez tout le courant 61ectrique, au niveau du disjoncteur principal ou de la boTte Les diaphragmes du r6gulateur de pression et du 6 fusibles.
  • Page 29 BRULEUR CENTRAL conversion du gaz PL La taille est indiqu#e par BrQleur grand format de 15 000 Btu/h (ModUles PGP953} un chiffre et le type de gaz par une lettre, sur le dessus ou le c6t#. (Important...
  • Page 30 Instructions d'installation CHANGEZ LES DIAPHRAGHES CHANGEZ LES DIAPHRAGHES BROLEURS DE LA TABLE DE BRULEURS DE LA TABLE DE CUISSON (SUITE} CUISSON (SUITE} BROLEUR CENTRAL BROLEUR AVANT GAUCHE Br_leur 6 trois anneaux de 20 000 Btu/h (ModUles (ModUles PGP959 et CGP350) PGP959 et CGP350) Vis de plaque Injecteurs 5 orifice...
  • Page 31 Instructions d'installation CONVERSION AU GAZ PROPANE (LP)(SUITE) . Si les flammes sont trop petites ou si elles AJUSTEZ LES FLAMMES DES clignotent, ouvrez le robinet davantage BROLEURS dans le r6glage original. Allumez tousles br01eurs au maximum . ISi les flammes s'61oignent du br01eur, v6rifiez les flammes.
  • Page 32 Notes.
  • Page 33 Estufa a Gas Sellada de 30°' stal ci" PGP953, PGP959, CGP350 j r_Preguntas? Llame a 800.GE.CARES (800.432.2737) o visite nuestro sitio web en: GEAppliances.com "---" En Canadd, Ilame al 1.800.561.3344 o visite nuestro sitio web en: www.geapplionces.ca PARA SU SEGURIDAD:...
  • Page 34: Instrucciones De Instalaci6N

    Instrucciones d e Instalaci6n INSTRUCCIONES IMPORTANTES DE SEGURIDAD REOUISITOS ELI_CTRICOS PARTES INCLUIDAS Este electrodom6stico deber6 ser suministrado con la frecuencia y el voltaje adecuados, y set conectado a un circuito derivado individual correctamente conectado a tierra, protegido por un 2 Tornillos Regulador disyuntor o fusible con el amperaje...
  • Page 35 Instrucciones d e Instalaci6n LISTA DE CONTROL DE PRE-INSTALACION AI preparar la abertura de la estufa, Retire las instrucciones de instalaci6n asegOrese de que el interior del gabinete y paquete de instrucciones y lea las mismas de la estufa no interfieran uno con otto.
  • Page 36 Instrucciones d e Instalaci6n PREPARACION DE LA ABERTURA MANTENGA LAS SIGUIENTES UBICACI6N DEL SUMINISTRO DE DIMENSIONES MINIMAS DE DESPEJE GAS RECOMENDADA DESDE LA 13" de I PARED TRASERA 1"coma m inima, m6×ima debajo R - Despeje minima desde Io Pared Trasera de gabinetes desde la apertura desprotegidos...
  • Page 37 Instrucciones d e Instalaci6n INSTALACION DE LA UNIDAD DE LA ESTUFA ADHIERA LOS SOPORTES A LA UB!OUE EL TOMACORRIENTE ELECTRICOV LA VALVULA DE CIERRE ESTUFA DE GAS DEBAJO DEL GABINETE Retire el tornillo del costado de la estufa y atornille el soporte al costado de la unidad de la estufa.
  • Page 38 Instrucciones d e Instalaci6n INSTALACION -CONEXIONES DE GAS r_1 BRINDE EL SUMINISTRO DE GAS INSTALACI6NDELREGULADOR EN LA ADECUADO PARTE INFERIOR DELA CAJADELOS QUEMADORES Esta estufa fue diseBada para funcionar con gas natural con una presi6n de admisi6n de columna Atornille el regulador de agua de 5"...
  • Page 39 Instrucciones d e Instalaci6n PI_RDIDAS CONTROLE LAS INSTALACI6N SOBRE EL HORNO INCORPORADO EL CONTROL DE PERDIDAS DEL ELECTRODOMESTICO SE DEBERA REALIZAR DE ACUERDO CON LAS Para acceder a instrucciones de instalaci6n INSTRUCCIONES DEL FABRICANTE completas, consulte la instalaci6n del homo incorporado.
  • Page 40 Instrucciones d e Instalaci6n INSTALACION - CONEXIONES ELECTRICAS ,tkADVERTENCIA - De_co_ecte todas las fuentes el6ctricas del disyuntor principal o de la caja de fusibles antes de realizar la instalaci6n. SUIvlINISTRO V TOIACORRIENTE ELECTRICO Se deber6 usar un suministro y tomacorriente el6ctrico adecuado para utilizar las partes el6ctricas de su estufa.
  • Page 41 Instrucciones d e Instalaci6n QUEMADORES DE LA ESTUFA ENSAP1BLE DE LOS QUEMADORES DE LA ESTUFA El electrodo del encendido est6 expuesto. AsegOrese de no encender ningOn control de lu estufo mientrus se retiro lu porte superior del quemudor. No retire Io porte superior ni toque el electrodo de ningQn quemudor mientros otro quemudor...
  • Page 42 Instrucciones d e Instalaci6n QUEMADORES DE LA ESTUFA (CONT.) E_] ENCENDIDO DE LOS QUEMADORES PARRILLAS DE LOS QUEMADORES Las tres parrillas de los quemadores fueron Encendido a Chispa de la Estufa- AI girar la dise_adas para posiciones especificas. Para una perilla de la estufa a la posici6n LITE,el encendido m6xima estabilidad, estas parrillas s61odeberian produce una serie de chispas el6ctricas (sonidos...
  • Page 43 Instrucciones d e Instalaci6n LISTA DE CONTROL DE FUNCIONAHIENTO combustible y presi6n adaptados para la estufa AsegOresede que todos los controles queden en al salir de f6brica. la posici6n OFF (Apagado). AsegOresede que la estufa se encuentre en la posici6n UNLOCKED AI ordenar piezas, siempre incluya el n0mero de (Desbloqueada) (en modelos con este serie, n0mero de modelo y un c6digo de letra...
  • Page 44 Instrucciones de Instalaci6n C6MO REALIZAR LA CONVERSION A LP HERRAMIENTAS QUE NECESITARA PARA INFORMACI6N DE SEGURIDAD LA CONVERSI6N A LP QUE DEBERIA CONOCER Los orificios del quemador y el regulador de presi6n Llave de tuercas de est6n configurodos para gas natural. Para usar gas LP, los orificios del quemador y el regulador Gafas de Seguridad...
  • Page 45 Estas marcas denotan la ubicaci6n Cabeza quemador central extra grande coda orificio con el quemador de la estufa. 020201 ©uemador Para Modelos PGP953 Extendida IM(is colto) Espita Para Modelos PGP959y CGPS50 Base Espita del orificio ubicada a trav6s de...
  • Page 46 Instrucciones d e Instalaci6n COMO REALIZAR LA CONVERSION A LP (CONT.) _7 CAMBIE LOS ORIFICIOS DEL CAMBIE LOS ORIFICIOS DEL QUEMADOR DE LA ESTUFA (CONT.) QUEMADOR DE LA ESTUFA (CONT.) QUEMADOR CENTRAL Quemador Frontal Izquierdo Quemador de Tres Anillos de 20,000 BTU/hr (Modelos PGP959 y CGP350) (Modelos PGP959 y CGP350)
  • Page 47 Instrucciones d e Instalaci6n C6MO REALIZAR LA CONVERSION A LP (CONT.} Prueba de Estabilidad de la Llama: AJUSTE LAS LLAMAS DEL QUEMADOR Perillas de reemplazo temporario. Prueba 1- Gire todos los quemadores al m6ximo y controle las llamas. Deberian ser azules con Gire la perilla de "HI"...
  • Page 48 Notas.

This manual is also suitable for:

Pgp959Cgp350

Table of Contents