Jenn-Air JGC1430 Installation Manual page 5

2, IFTHISUNITWILLHAVE A JENN-AIR MODEL
WALLOVENINSTALLED BELOW THISCOOKTOP.
NOTE1: Thisappliance anditsgasandelectrical supply
sources mustbeinstalled before thewallovenis installed.
Seeillustration ( Electrical WiringInformation - page7;
figure6)forrecommended electrical supply source
locations.
NOTE2"It maybenecessary t o extend gassupply piping
forthisappliance i ntoadjacent u nder-counter cabinetry
when a wallovenis installed below thisappliance.
Joina 3/8"NPTpipeelbow(locally available) tothemale
threads atthemanifold entrance. Whenjoined, e nsure
openthreads oftheelbowfacetoward therightsideof
theappliance. Install t heappliance i n itscounter c utout.
Joina 3/8"NPTpipenipple totheelbowusinga pipe
section of sufficient length toextend, h orizontally, beyond
therightsideofthewalloven.(Toaccomplish t hisit may
benecessary t o extend thepipesection intoadjacent
cabinetry.) Joinadditional 3/8"NPTelbow(s) a ndpipe
nipples, a s necessary, toaccomplish t hefollowing:
Jointheoutlet o ftheappliance pressure regulator
supplied w iththisappliance t othemalethreads ofthe
newly installed gassupply piping. I nstall t heappliance
regulator ina location which willbeaccessible b eside or
below thewalloven.Insure theappliance regulator is
installed withitsdirectional arrowpointing inthedirection
ofgasflow.Tighten the appliance r egulator to 20to 30
ft-lbsoftorque.
ILLUSTRATIVE GAS SUPPLY PIPING
(WALL OVEN INSTALLED BELOW 30" COOKTOP)
_1 -'/ BURNER BOX
_:I I /
_ (REAR OF APPLIANCE)
_i_I/" _:::::'.
::::::::::::::::::::: ::::::::::::::::::::::: MANIFOLD ,,
: 'i':':+: .","_:':" _ (3/8N PT)
:l_i.;:::i_:_;.:::_ LJ ENTRANCE "'"
iii! iiiiill ii! iiii_" __ _gE"-- ELBOW _PTAPI;R_-_AS_ sE
APPLIANCE MANUAL
PRESSURE SHUTOFF
REGULATOR VALVE
k iNkEr
ALL UNIT StDE APPROXIMATE CROSS SECTION ALL SUPPLY SIDE
PiPE JOINTS PROFILE OF WALL OVEN PIPE JOINTS
318" N.P.T. 1/2" N.P.T.
FIGURE4
Never tighten to more than 35 ft-lbs of torque. Always
use an approved pipe joint compound resistant to the
action of LP gas.
Locate and join a manual shut-off valve in an accessible
location in the gas line ahead of the appliance regulator
and external to the appliance for the purpose of turning on
or shutting off gas to the appliance.
Make additional pipe connections as necessary ahead of
the shut-off valve to the gas supply source. Assure all
pipe joint connections are gas tight.
II [e] I;tll/T;51#I li
Apply a non-corrosive leak detection fluid to all joints and
fittings in the gas connection between the supply line
shut-off valve and the cooktop. Include gas fittings and
joints in the cooktop if connections were disturbed during
installation. Check for leaks! Bubbles appearing around
fittings and connections will indicate a leak. If a leak
appears, turn off supply line gas shut-off valve, tighten
connections, turn on the supply line gas shut off valve,
and retest for leaks. Never test for gas leaks with an open
flame.
Note, regarding Figure 4, above:
° For convenience in service a union (not shown: locally
available) should be included in the piping illustrated in
figure 4, in a location most practical for the installation.
Generally, a practical location is in the cabinet below
this appliance, near the manifold entrance, rather than
in an adjoining cabinet.
If the alternative piping method shown in figure 5 is
selected for the installation, no union is required. (The
flexible appliance connector illustrated provides the
union joints necessary for servicing.) When a dividing
wall is present and a flexible connector is used, it is
recommended for convenience in both installation and
service, that the flexible connector pass through the
dividing wall. Any flexible connector used with this
appliance must satisfy all requirements stated in
the text accompanying figure 5.