Kenmore 40289032011 Installation Manual

Size : 420 X 297 (ram)
REMOVE PACKING MATERIAL
Cut the straps oil he carton and lift the carton off the drye*
Remove the dryer from the carton base
Check the dryer drum for all of the componen%
shown here
Literature Pack
CHECK AND CONNECT VENTING
1 Check the length of the exhaust vent it MUST NOT be longer than the
lengths shown in the chart below If it is too long, have it repaired or vented
elsewhere
2 Connect the dryer exhaust to the home exhaust system with rigid or semi
rigid metal duct DO NOT USE vinyl or foil duct for connecting the dryel
Make the transition as short as possible for best results
3 Check the exhaust hood on the outside wall Make sure it is not damaged
and that it is clear of lint buildup Make sure the damper is working properly
4 Check the exhaust for lint buildup or damage Make sure the duct is clean
and in good condition
Reeemm_ded 0 80 it 124 4 m) 41 fl (12 4 m)
_ _# 1 68 fl (207 m) 37 Jt ill 2"n)
2 5711 (]Z4 m) 33fl ri0]m)
4" (10.16 era) 3 47it (14 3 m) 29 fl (90 m)
Use only for short-run installation 0 74 it (226 m) 33 it (101 m)
1 6211 f189m) 29fl (88m)
2 51ft 1155 m) 251t 176m)
25" (6.35
¢m)
3 41 fl (12 5 m) 21 fl (6 5 m)
CONNECT POWER CORD
For gas dryers only.
#or electric dryers proceed to step #3b on the right
Plug the dryer into a 120 VAC, 60Hz
grounded 3 prong outlet
For electric dryers only.
For gas dryers proceed to step #30 on the IdL
FOUR-WIRE POWER CORD CONNECTION
(REQUIRED inall new constructionafter Jan 1,19%)
4-Wire system connections
A. External ground connector
A _ D
B. Greet, or bare copper wire of power cord
C. _f_" (]9 cm} UL listed strain relief
D. Center silver colored terminal block screw B
E
E. Neutral Grounding wire (green yellow} C J _ _ F
E Neutral wire (white or center wire}
U
i Remove the External ground connector
screw
2 Connect the ground wire (green or unwrapped} of the power cord to the
external ground connector scre_ If you want to connect B(Green or bare
copper wire of power cord} to the Neutral Post without assembling with
A(cabinet ground}, call the service technician
3 Looser, or remove the center terminal block screw
4 Connect the neutral wire (white or center wire} of the power cord and the
appliance ground wire (greet, with yellow stripes} under the cenhal screw
of the terminal block
5 Connect the other wires to the outer terminal block screws Tighter, screws
B Tighten the strain relief screws
X [nsed the tab of the terminal block cover into your Dryer's rear panel slot
Secure the cover with a hold dowr, screw
THREE-WIRE POWER CORD CONNECTION
(NOT permitted in new constructionafter Jan 1,19%)
3-Wire system connections
A. External ground connector
B. Neutral grounding wire (green/yellow)
C. Cer, ter silver colored terminal block screw
D. Neuhal wire (white or center wire}
E. s/4_' (19 cm} UL listed strain relid
] Looser, or remove the center terminal block
screw
2 Connect the neutral wire (white or center wire} of the power cord to the
centel, silver colored terminal screw of the terminal block Tighter, screw
3 Connect fl:e other wires to outer terminal block screws
fighter, screws
4 Tighter, the strain relief screws
5 Insert fi:e tab of the terminal block cover into your DryeFs rear par,el slot
Secure the cover with a hold dowr, screw
CONNECT GAS SUPPLY
For gos mode_ only
1 Connect the dryer to your laundry room s gas supply using a new flexible
stainless steel connector with a 3/8" NPT fitting
Never reuse an old flex connecto_
2 Securely tighten all connections be+ween the dryer and he laundry room's
gas supply Turn on the gas supply and check all connections for leaks with
a non corrosive leak detection fluid
3/8" NPT Gas /8" NPT Pipe Plug
Connection
AGA!CSA-42ertifled
Stainless Steel Shutoff: Valve
Flexible Connector
LEVELINGTHE DRYER
1 To set the dryer to the
same height as the washel,
fully retract the leveling
feet by t_urning them coun
terclockwise, then loosen
the legs by turning them
clockwise
.evel
Leveling Feet
2 Adiust the leveling feet only as
much as necessary to level the
dryec Extending the leveling fee+
more than necessary can cause
the dryer to vibra'e
HEATERCHECK
Perform the following steps to check heater operation after
removing the literature pack and any other obiects from the
drum
1 Close the door and press the POWER button to turn oil the controls
2 Rotate the CYCLE SELECTOR KNOB to select a hea'ed cycle, such as
NORMAL.
3 Press the START/PAUSE button to start the cycle
After approximately one minute, open the door and check for hea" if no
heat is felt after approximately 2 minutes, consuft the troubleshooting sec
tion of the owner's manual
FINAL CHECKS
Use the following checklist to ma ke sure you have complet
ed all of the installation steps
INSTALLATION STEP
1 - REMOVE PACKING MATERIAL
2 - CHECK AND CONNECT VENTING
3 - CONNECT POWER CORD
4 - CONNECT GAS SUPPLY (For gas models only)
5- LEVEL THE DRYER
6 - HEATER CHECK
Screws
For more information, refer to Installation Instructions included in the pedestal
For accessory installation instructions, consult the ins:allafion instructions
included with each accessory
LP CONVERSION KiT
SiDE VENT KIT - DV ]A XAA
STACKING KIT- SK 5AXAA
Test for proper operation by running the dryer through a
complete cycle.
Please consult your owner's manual for complete details.
P/No. DC68-O289gA-O1