Husqvarna YTH22V46 Owner's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Mower
  5. OWNER'S YTH22V46
  6. Owner's manual

Husqvarna YTH22V46 Owner's Manual

Instruction manual
Hide thumbs Also See for YTH22V46:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
YTH22V46
Owner's Manual / 96043010100 / 2009-12
532 43 33-16

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna YTH22V46

Summary of Contents for Husqvarna YTH22V46

  • Page 1 YTH22V46 Owner's Manual / 96043010100 / 2009-12 532 43 33-16...

  • Page 2: Safety Rules

    SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Slow down before turning. WARNING: In order to prevent ac ci den tal •...
  • Page 3 SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to GENERAL SERVICE the presence of children. Children are often attracted to • Never operate machine in a closed area. the ma chine and the mowing activity.

  • Page 4: Table Of Contents

    PRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. Gasoline Capacity 2.50 Gallons and type: Unleaded Regular • Follow a regular schedule in maintaining, caring for and using your tractor. Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) •...

  • Page 5: Assembly

    UNASSEMBLED PARTS Slope Sheet (1) Oil Drain Tube (2) Keys ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Stan dard LABEL wrench sizes are listed.

  • Page 6: Assembly

    ASSEMBLY ✓ CHECKLIST NOTE: You may now roll your tractor off the skid. Follow the BEFORE YOU OPERATE YOUR NEW TRAC TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST instructions below to remove the tractor from the skid. PERFORMANCE AND SATISFACTION FROM THIS WARNING: Before start ing, read, un der stand and fol low QUALITY PRODUCT.

  • Page 7: Operation

    OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. FAST SLOW REVERSE HIGH NEUTRAL CHOKE IGNITION SWITCH ENGINE START MOWER HEIGHT MOWER LIFT REVERSE ENGINE ON PARKING BRAKE ENGINE OFF OPERATION SYSTEM (ROS) CLUTCH/BRAKE...
  • Page 8 OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Fig.
  • Page 9 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles.
  • Page 10 OPERATION TO USE CRUISE CONTROL (J) (See Fig. 7) TO ADJUST GAUGE WHEELS (See Fig. 9) The cruise control feature can be used for forward travel Gauge wheels are prop er ly ad just ed when they are slight ly only.
  • Page 11 OPERATION TO TRANSPORT (See Figs. 3 and 11) REVERSE OPERATION SYSTEM (ROS) When pushing or towing your tractor, be sure to disengage Your tractor is equipped with a Reverse Operation System transmission by placing freewheel control in free wheel ing (ROS).

  • Page 12: Before Starting The Engine

    OPERATION TO START ENGINE (See Fig. 3) BEFORE STARTING THE ENGINE When starting the engine for the first time or if the engine CHECK ENGINE OIL LEVEL has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

  • Page 13: Operation

    OPERATION MOWING TIPS PURGE TRANSMISSION • Mower should be properly leveled for best mowing CAUTION: Never engage or disengage performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. freewheel lever while the engine is •...

  • Page 14: Maintenance Schedule

    MAINTENANCE BEFORE EVERY EVERY EVERY EVERY EVERY BEFORE MAINTENANCE EACH SEASON STORAGE SCHEDULE HOURS HOURS HOURS HOURS Check Brake Operation Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Clean Debris Off Steering Plate ck Transaxle Cooling...

  • Page 15: Maintenance

    MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Re place Always observe safety rules when per form ing any bent or damaged blades. main te nance. CAUTION: Use only a replacement blade ap- BRAKE OPERATION proved by the manufacturer of your tractor.

  • Page 16: Transaxle Cooling

    MAINTENANCE V-BELTS OIL DRAIN VALVE Check V-belts for deterioration and wear after 100 hours CLOSED of operation and replace if necessary. The belts are not ad just able. Re place belts if they begin to slip from wear. LOCKED POSITION TRANSAXLE COOLING DRAIN The transmission fan and cooling fins should be kept clean...
  • Page 17 MAINTENANCE MUFFLER DECK WASHOUT PORT (See Fig. 19) Inspect and replace corroded muffler and spark arrester (if Your tractor’s deck is equipped with a washout port on equipped) as it could create a fire hazard and/or damage. its surface as part of its deck wash system. It should be utilized after each use.

  • Page 18: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. •...
  • Page 19 SERVICE AND ADJUSTMENTS • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO • Insert end of link (E) into hole in front mower bracket CHASSIS - Position hole in arm over pin (B) on outside and secure with washer and retainer spring (J). of tractor chassis and secure with retainer spring.
  • Page 20 SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see step in Visual Adjust- ment instructions above. Make sure tires are properly inflated to the PSI shown on • Recheck measurements, adjust if necessary until both tires. If tires are over or under inflated, it may affect the sides are equal.

  • Page 21: To Replace Mower Blade Drive Belt

    SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT TO REPLACE MOTION DRIVE BELT (See Fig. 30) (See Fig. 31) Park the tractor on level surface. En gage parking brake. The mower blade drive belt may be replaced without tools. For as sis tance, there is a belt installation guide decal on Park the tractor on level surface.
  • Page 22 SERVICE AND ADJUSTMENTS TO REMOVE WHEEL (See Fig. 32) TO REMOVE CABLES, REVERSE ORDER - • BLACK cable first from chassis and then from the fully • Block up axle securely. charged battery. • Remove axle cover, retaining ring and washers to allow •...

  • Page 23: To Replace Headlight Bulb

    SERVICE AND ADJUSTMENTS TRANSMISSION TO REPLACE HEADLIGHT BULB • Raise hood. REMOVAL/RE PLACE MENT • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely Should your transmission require removal for service or back into the hole in the backside of the grill.

  • Page 24: Storage

    STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS WARNING: Never store the trac tor with FROM FORMING IN ES SEN TIAL FUEL SYSTEM PARTS SUCH gas o line in the tank inside a building AS CARBURETOR, FUEL FIL TER, FUEL HOSE, OR TANK...

  • Page 25: Troubleshooting

    TROUBLESHOOTING PROBLEM CAUSE CORRECTION 1. Out of fuel. 1. Fill fuel tank. Will not start 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4.

  • Page 26: Trou Ble Shoot Ing

    TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues 1. Faulty operator-safety presence control 1. Check wiring, switches and connections. If not system. corrected, contact an authorized service center/ to run when oper- department. ator leaves seat with attachment clutch engaged 1. Worn, bent or loose blade. 1.

  • Page 27: Repair Parts

    TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 SCHEMATIC SCH11 BATTERY SOLENOID STARTER FUSE AMMETER BLACK (OPTIONAL) WHITE WHITE ATTACHMENT CLUTCH (CLUTCH OFF) BLACK CLUTCH/BRAKE GRAY (PEDAL UP) REVERSE SWITCH BLACK (NOT IN REVERSE) BLACK BLACK...
  • Page 28 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 ELECTRICAL T06S With 12V Outlet Option With Service Minder Option...
  • Page 29 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 ELECTRICAL PART DESCRIPTION 532 16 34-65 Battery 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 532 19 32-28 Box Battery 532 17 61-38 Switch Interlock Push-In 532 18 37-59...
  • Page 30 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 CHASSIS chassis-tex_TEX GT HUSQ_68...
  • Page 31 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 CHASSIS PART PART DESCRIPTION DESCRIPTION 532 40 50-12 Logo 532 40 41-37 Plug Hole Dash Lower 532 40 87-03 Dash 532 41 45-80 Console Asm. Deck Lift 532 41 10-46...

  • Page 32: Drive Parts

    TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 DRIVE drive-tex_K46_pedal_48...
  • Page 33 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 DRIVE PART PART DESCRIPTION DESCRIPTION 532 42 61-20 Transaxle, Tufftorq K46BT 532 40 31-18 Handle Parking Brake 532 12 35-83 Key Square 872 11 06-22 Bolt 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
  • Page 34 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 ENGINE SPARK ARRESTER KIT...
  • Page 35 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 ENGINE PART DESCRIPTION - - - - - - Engine Briggs Model No. 441777-1195-B1 532 14 97-23 Muffler 532 19 43-20 Keeper Belt Engine 532 40 54-72 Pulley Engine...
  • Page 36 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 STEERING ASSEMBLY 53 8 steering-tex_HUSQHR_1_r1...
  • Page 37 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 STEERING ASSEMBLY PART DESCRIPTION 532 41 64-80 Wheel, Steering 532 19 59-68 Axle Cast Iron 532 40 30-87 Spindle Asm., LH 532 40 30-88 Spindle Asm., RH 532 12 49-31...

  • Page 38: Mower Deck

    TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 MOWER DECK 46_tex_lt_pred_11_r1...
  • Page 39 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 532 41 08-63 Mower Housing 532 19 94-77 Arm Brake Mower 532 40 55-06 Cover Mandrel RH...

  • Page 40: Mower Lift

    TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 MOWER LIFT 101* lift-tex_22 *Key 91 may be substituted for Key 101 PART PART DESCRIPTION DESCRIPTION 532 42 20-27 Shaft Asm., Lift 817 00 06-12 Screw 3/8-16 x .75 Smgml Tap/R.Z 532 19 52-31 Lever Asm., Lift RH...
  • Page 41 TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 SEAT ASSEMBLY seat-tex_6.5SL_3 PART PART DESCRIPTION DESCRIPTION 873 80 05-00 Nut, Lock 5/16-18 unc 532 42 40-68 Seat 532 19 76-61 Handle Slide Seat 532 18 01-66 Bracket Pivot Fender...

  • Page 42: Wheels And Tires

    TRACTOR - - MODEL NUMBER YTH22V46 (96043010100), PRODUCT NO. 960 43 01-01 DECALS PART PART DESCRIPTION DESCRIPTION 532 14 50-05 Decal, Battery Dnge/Poi 532 41 16-58 Decal, Fender Warning 532 16 03-96 Decal, Mower V-Belt Schematic 532 42 20-12 Decal, Hood...
  • Page 43 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
  • Page 44 12.14.09 TH Printed in the U.S.A.

This manual is also suitable for:

917.289620Yth23v48

Table of Contents