Table of Contents
Advertisement
Basic Operation
Preparation before playing:
1. Connect the DVD player to your TV and amplifier.
2. Turn on the TV.
3.
Set the TV to the AV input connected to the DVD player.
4. Turn down the volume on your amplifier, and then power it on.
5.
Set the amplifier to the AV input connected to the DVD player.
STEP 1 - Press POWER to
start the player. The DVD
logo appears on the TV
screen.
STEP 2 - Press OPEN/CLOSE either on
the front panel or remote control. When
the tray is opened, place the disc on the
tray with the label side up. Press OPEN/
CLOSE again to close the disc tray.
Using the remote control
Point the remote control at the remote sensor.
(The pictures below are for reference only.)
7m
Basic Playback
STEP 3 - Press the PLAY/PAUSE
button on the front panel or
remote control. The player will
automatically read and identify
the disc, and begin playback.
Remarks: Do not expose the remote sensor of the
DVD Player to a strong light source, such as direct
sunlight.
Notes:
Point the remote control directly at the
player's remote sensor.
Do not leave the remote control in an
extremely hot or humid place.
Do not spill water or put anything wet
on the remote control.
Battery life is 1 year under normal
conditions.
8
Modes and Features Setup
SETUP
In stop mode, press <SETUP>, and the TV screen
will display the Setup Menu as follows:
Setup Menu
Press
to change items
A. Press <ENTER> to display each submenu
B. Press <SETUP> to exit the Setup Menu
System Setup
Select [SYSTEM SETUP] in the Setup Menu, and
the submenu will arise as follow:
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
VIDEO
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
Press
to select the menu item
A.Press <ENTER> or
to set
B.Press
or
repeatedly to return to the Setup Menu
1. Select [TV SYSTEM] in the System Setup Menu
to display the [TV SYSTEM] Submenu:
SYSTEM SETUP
TV SYSTEM
NTSC
SCREEN SAVER
PAL
VIDEO
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
Press
to select the menu item
A.Press <ENTER> to set
B.Press
or
repeatedly to return to the Setup Menu
C.Press <SETUP> to exit the Setup Menu
[NTSC] -Select if you are using NTSC signal system to match your TV set.
[PAL]
-Select if you are using PAL signal system to match your TV set.
* The default setting is NTSC.
Advanced Features
2. SCREEN SAVER
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
ON
VIDEO
OFF
TV TYPE
PASSWORD
RATING
DEFAULT
EXIT SETUP
If the screen saver is on,when your DVD player is in Stop,Open,or No Disc
state,or there is a frame frozen for more than 180sec,the screen saver will
be displayed.This feature can protect the screen from damage.
[ON] - Choose this setting to activate the screen saver.
[OFF]- Choose the setting to cancel the screen saver.
* The default setting is ON.
3. VIDEO
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
VIDEO
S-VIDEO
TV TYPE
INTERLACE-YUV
PASSWORD
TV-RGB
RATING
P-SCAN YPBPR
DEFAULT
EXIT SETUP
Note: The Composite video and S-video output is always available.
[S-VIDEO]-Select if you connect the DVD player to your TV using
S-VIDEO output.
[INTERLACE-YUV] -Select if you connected the DVD player to your TV
using the YUV(Y,Cb,Cr) output.
[TV-RGB] -not available in North America.
[P-SCAN YPbPr] - Select if you connected the DVD player to your TV
using progressive scan(Y,Pb,Pr).
* The default setting is S-VIDEO.
4. TV TYPE
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
VIDEO
TV TYPE
4:3 PS
PASSWORD
4:3 LB
RATING
16:9
DEFAULT
EXIT SETUP
[4:3 PS] -Pan and scan refes to pictures where part of pictures is cut
off so it fills the whole screen.
[4:3 LB] -Letter Box refers to pictures where black bands appear at
the top and bottom.
[16:9]
-The picture fills the screen of a wide-screen(16:9) television.
* The default setting is 4:3PS.
Note: Not all DVDs offer movies in Full Screen format. If not, the disc
will override your TV Display setting and the movie will be
displayed in Letter box format.
9
Advertisement
Table of Contents
