Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H7678
Summary of Contents for Grizzly H7678
- Page 1 18 GAUGE DEEP STAPLER KIT MODEL H7678 INSTRUCTION MANUAL COPYRIGHT © JULY, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
-
Page 2: Safety Instructions For Pneumatic Tools
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. - Page 3 UNINTENTIONAL FIRING. Do not carry tool with hand on trigger and always disconnect from air when not in use. H7678 18 Gauge Deep Stapler Kit 17. DISCONNECT TOOLS before ser- vicing, changing accessories, or moving to another location. 18. DO NOT OVERREACH. Keep proper footing/balance at all times.
- Page 4 COMPRESSED AIR RATING. Do not connect the stapler to com- pressed air that exceeds 120 PSI. CHECK VALVE. Do not use a check valve or any other fitting that allows air to remain in the tool. H7678 18 Gauge Deep Stapler Kit...
- Page 5 82 decibels. To protect your hearing, always wear ANSI approved ear protection when operating this stapler. H7678 18 Gauge Deep Stapler Kit Never point this stapler at yourself or another person! Always pay attention to the direction this stapler is pointed.
-
Page 6: Contact Info
Foreword We are proud to offer the Grizzly Model H7678 18 Gauge Deep Stapler Kit. This model is part of a growing Grizzly family of fine pneumatic tools. When used accord- ing to the guidelines set forth in this man- ual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s... - Page 7 Unpacking Your Model H7678 left our warehouse in a carefully packed box. If you discover the stapler is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice. Save the containers and all packing mate- rials for possible inspection by the car- rier or its agent.
-
Page 8: Compressed Air System
Compressed Air System The Model H7678 is designed to be oper- ated at 60-100 PSI using clean, dry, regu- lated, compressed air. DO NOT exceed the 120 PSI maximum operating pres- sure for your model. Before using your new stapler, regulate the air pressure on your air compressor to the minimum PSI for your model. - Page 9 Serious injury may occur. H7678 18 Gauge Deep Stapler Kit 5. Without pressing the trigger, depress the safety yoke mechanism against a scrap piece of wood that is clean and free of any knots, nails, or other foreign objects.
- Page 10 Operating connect fitting. hold the stapler perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of staples you have loaded. H7678 18 Gauge Deep Stapler Kit Pusher...
- Page 11 H7678 18 Gauge Deep Stapler Kit Figure 5. Example of staple deflection. 5. Pull the trigger. — If the staple drove into the wood far enough, continue with your intended operations.
-
Page 12: Clearing Jammed Staples
DO NOT use dirty or damaged staples! 8. Slide the magazine forward until the catch lever engages. Cover H7678 18 Gauge Deep Stapler Kit... - Page 13 5. The top of the piston should now be visible inside the cylinder, which is housed in the head of the stapler. H7678 18 Gauge Deep Stapler Kit 6. Open the nose cover as if to clear a jammed staple.
-
Page 14: Cleaning And Lubrication
Lubricating Pneumatic tool oil has been included with your new Grizzly stapler to help maintain its useful life. Place two to three drops of oil in the stapler air inlet (as shown in Figure 7) before every use, or after 2 hours of continuous use. - Page 15 �� � � �� � �� � �� � �� � �� � �� �� �� �� H7678 18 Gauge Deep Stapler Kit �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��...
- Page 16 RUBBER HANDLE PH7678068 O-RING PH7678069 END CAP PH7678070 1/4" NPT MALE CONNECT PH7678071 AIR PLUG COVER PAW03M HEX WRENCH 3MM PAW04M HEX WRENCH 4MM PLW01M LOCK WASHER 5MM PH7678074 CARRYING CASE PH7678075 PISTON REPAIR KIT H7678 18 Gauge Deep Stapler Kit...
-
Page 17: Troubleshooting
5. Driver or driver guide are worn Stapler does not 1. Staple is jammed in magazine fire. 2. Piston shaft is damaged. 3. Air pressure too low. H7678 18 Gauge Deep Stapler Kit ing are damaged. staples from moving freely in magazine. of lubrication. valve. -
Page 18: Warranty And Returns
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. -
Page 19: Warranty Card
____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times. - Page 20 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...