USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed. INFLUENCE ALCOHOL. WORKSHOP CHILD UNDER DRUGS H7677 18 Gauge Stapler Kit...
Page 3
UNINTENTIONAL FIRING. Do not carry tool with hand on trigger and always disconnect from air when not in use. H7677 18 Gauge Stapler Kit 17. DISCONNECT TOOLS before ser- vicing, changing accessories, or moving to another location. 18. DO NOT OVERREACH. Keep proper footing/balance at all times.
Page 4
COMPRESSED AIR RATING. Do not connect the stapler to com- pressed air that exceeds 120 PSI. CHECK VALVE. Do not use a check valve or any other fitting that allows air to remain in the tool. H7677 18 Gauge Stapler Kit...
Page 5
82 decibels. To protect your hearing, always wear ANSI approved ear protection when operating this stapler. H7677 18 Gauge Stapler Kit Never point this stapler at yourself or another person! Always pay attention to the direction this stapler is pointed.
Foreword We are proud to offer the Grizzly Model H7677 18 Gauge Stapler Kit. This model is part of a growing Grizzly family of fine pneumatic tools. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoy- able operation and proof of Grizzly’s com-...
SECTION 3: SET UP Unpacking Your Model H7677 stapler kit left our ware- house in a carefully packed box. If you discover the stapler is damaged after you have signed for delivery, please immedi- ately call Customer Service at (570) 546- 9663 for advice.
Compressed Air System The Model H7677 is designed to be oper- ated at 60-100 PSI using clean, dry, regu- lated, compressed air. DO NOT exceed the 120 PSI maximum operating pres- sure for your model. Before using your new stapler, regulate the air pressure on your air compressor to the minimum PSI for your model.
Page 9
Serious injury may occur. H7677 18 Gauge Stapler Kit 5. Without pulling the trigger, depress the safety yoke mechanism against a scrap piece of wood that is clean and free of any knots, nails, or other foreign objects.
2. To test for proper staple penetration, hold the stapler perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of staples you have loaded. H7677 18 Gauge Stapler Kit...
Page 11
More air pressure will make the staple go deeper and less air pressure will decrease the staple penetration. H7677 18 Gauge Stapler Kit Single/Bump Fire Operation The stapler is designed to fire one staple at a time, or one after another, using the trigger switch.
Inspect the staple stick. If it is bent or damaged, insert a new staple stick that only contains clean, undamaged staples. DO NOT use dirty or damaged staples! Latch the magazine closed. FROM Cap Screw H7677 18 Gauge Stapler Kit...
Page 13
A replacement piston and O-ring kit, part PH7677069, may be purchased for the Model H7677. Always disconnect air from stapler whenever servicing! During main- tenance, a stapler connected to air...
Lubricating Special oil has been included with your new Grizzly stapler to help maintain its useful life. Place two to three drops of oil in the stapler air inlet (as shown in Figure 9) before every use, or after 2 hours of continuous use.
Page 16
COMPRESSION SPRING CAP SCREW M4-.7 X 16 TALL STOPPER LOCK NUT M4-.7 RUBBER HANDLE CASE O-RING END CAP 1/4" NPT MALE CONNECT AIR PLUG COVER HEX WRENCH 3MM HEX WRENCH 4MM CARRYING CASE PISTON REPAIR KIT H7677 18 Gauge Stapler Kit...
5. Driver or driver guide are worn Stapler does not 1. Staple is jammed in magazine fire. 2. Piston shaft is damaged. 3. Air pressure too low. H7677 18 Gauge Stapler Kit ing are damaged. staples from moving freely in magazine. of lubrication. valve.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 19
____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times.
Page 20
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...