NAD VISO THREE Owner's Manual page 7

6 REMOTE SENSOR
Point the VR 3 remote control at the remote sensor and press the
buttons. Do not expose the remote sensor of the VISO THREE to a strong
light source such as direct sunlight or illumination. If you do so, you may
not be able to operate the VISO THREE with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
7 VACUUM FLUORESCENT DISPLAY (VFD)
Provide visual information about the current settings like displaying the
active Source, volume level, playback information, applicable RDS/DAB
display information and other related indicators.
8 SOURCE
Toggle these buttons to select through the following SOURCE modes
– CD, iPod, Tuner (AM, FM or DAB as applicable), USB, Audio 1, Audio 2
and Front.
9 VOLUME
The VOLUME control adjusts the overall loudness of the signal being fed
to the loudspeakers or headphones.
·
Turn clockwise to increase the volume level; counter clockwise to
lower it.
· The VOLUME knob is also used to increment/decrement the Bass
and Treble levels as well as in shifting BALANCE levels.
10 PHONES
• Accepts stereo headphone using a standard 1/4-inch stereo phone
plug (use a suitable adaptor for headphones equipped with a
smaller plug).
•
Plugging in headphones automatically mutes output from the
speakers.
11 FRONT INPUT
Use these convenience jacks for occasional sources such as tape player
or any analog audio sources.
• If your source has a single audio out jack only or is marked "mono
output", plug this into the VISO THREE's Front Input "R (Mono)".
• On the other hand, if your source has two output jacks indicative of
stereo output, insert both jacks into the VISO THREE' s corresponding
Front Input "L" and Front Input "R (Mono)" to achieve stereo output as well.
USB
Connect a USB memory stick to this input. Refer also to the item about USB
MODE at the USING THE VISO THREE section of the OPERATION page.
12 DISC TRAY
• With the disc tray open, insert a CD or other compatible media disc
face down onto the tray. Place the disc in the drawer, centered in
the smaller circular recess, with its label facing UP.
• "No Disc" appears on the VISO THREE's VFD if the drawer is closed
with a disc placed upside down or no disc loaded.
IDENTIFICATION OF CONTROLS
13 OPEN/CLOSE
• Press this button to open and close the disc drawer and
simultaneously select the internal CD player.
• Pressing the [OPEN/CLOSE] button will also automatically switch
ON the VISO THREE from standby mode and at the same time draw
open the disc tray.
• If the current Source is not CD mode (i.e., FM mode) and [OPEN/
CLOSE] is pressed, the VISO THREE will immediately switch to CD
mode as the disc tray draws open.
14 PLAY/PAUSE
•
Press this button to toggle between Play and Pause of a CD or other
compatible media disc.
•
Press to start play or resume play after Pause. The icon "
illuminated in the VFD indicating the VISO THREE is in playback
mode.
•
If the disc tray is open, press this button to automatically close the
tray and start playback if a disc is loaded.
•
During playback, press this button to stop playback temporarily,
keeping the optical pickup at its current position on the disc. The
icon " " is illuminated in the VFD indicating the VISO THREE is
in pause mode. To resume playback at the exact point where it
stopped, press [PLAY/PAUSE] again.
• Pressing the [PLAY/PAUSE] button will also automatically switch ON
the VISO THREE from standby mode and start playback if a disc is
loaded.
15 STOP
• During disc playback, press this button to STOP disc or file playback.
The display reverts to showing the number of tracks and total
playing time on the disc; for WMA/MP3 files, the display will revert
to the total number of files.
• Pressing [STOP] button will result to full stop of current track/file
playback. Pressing [PLAY/PAUSE] after stop mode will start playback
of the first track/file/program.
• If the VISO THREE was programmed to play a selection of tracks/files,
the program will be retained in the player's memory. Pressing the
[STOP] button twice during program playback will delete the whole
program list.
FRONT PANEL
" is
7