Trigon Energy User Manual

Integrated amplifier
Hide thumbs Also See for Energy:

Advertisement

USER S MANUAL FOR INTEGRATED AMPLIFIER
Energy
MONO
PROTECT
SPLITT
LS-OFF
MUTE
MODE
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Energy and is the answer not in the manual?

Questions and answers

Summary of Contents for Trigon Energy

  • Page 1 USER S MANUAL FOR INTEGRATED AMPLIFIER Energy MONO PROTECT SPLITT LS-OFF MUTE MODE...
  • Page 2: Table Of Contents

    CONTENTS Introduction General Description Safety Information Installation Information Warranty and Service Information Initial Setup Front Panel Controls Rear Panel Connections Remote Control The MODE Function Balance Control Initial Volume Level Display Brightness Record Output Activation Unity Gain Home Theater Throughput Input Levels Factory Default Settings What to do, if ...
  • Page 3: Introduction

    1 Vorwort 1 Introduction Trigon Valued - Customer, Energy We are excited that you have chosen to purchase the integrated amplifier. This unit was built using the highest quality control to insure utmost precision in manufacturing. Whether you are a beginner to High-Fi or advanced user, it is highly recommended that you read and understand this User s Manual thoroughly before using your new integrated amplifier.
  • Page 4: Safety Information

    2.1 Safety Information Trigon Elektronik GmbH will not assume any responsibility for damages occurred from unsafe handling of the product or from not adhering to the recommend safety instructions below. The amplifier should not be used un-monitored in close proximity to heat producing devices such as Water heaters, Fireplaces or Flammable materials.
  • Page 5: Warranty And Service Information

    Trigon the production cycle to insure that all products meet our quality expectations. Trigon Elektronik GmbH If a problem is experienced, offers a three-year warranty. This warranty covers repairs for any manufacturing defects.
  • Page 6 This LED shines, if the Stereobalance is shifted to the right Volume Knob : This knob is used to set and adjust the volume of the Energy. It is designed as a pulse generator without an end-stop where, at each step, an electronic pulse is transmitted to the microprocessor which in turn handles the electronic volume control.
  • Page 7: Rear Panel Connections

    LED ON : This LED will light up when the Energy is powered on. (operation display) Input pushbutton < : Pressing this button will select every next input before adjustment of the previous one.
  • Page 8 Tuners, CD Players, Tape Deck, etc. Turntables will need a separate phonostage (such as the Trigon Vanguard II or Advance) Energy to amplifier the signal of the phono cartridge to a level which the can accept.
  • Page 9: Remote Control

    3 Ohm are connected. Never short- circuit the binding posts in order to avoid damage to your integrated amplifier. 3.3 Remote Control Energy offers an optional IR Remote called the Director. The Director is a system remote that can control multiple components.
  • Page 10: The Mode Function

    4 The MODE Function We have included many additional features in this integrated amplifier that can be accessed via the MODE menu. The following functions are available in order of access in the MODE menu: - Balance control - Adjusting initial volume level - Adjusting Display brightness - Activating the Record Output - Unity Gain (Home Theater through-put)
  • Page 11 4.2 Adjusting Initial Volume Level Energy uses an electronic volume control system. In addition to offering better performance (over the conventional Potentiometer), it also allows for special features that have previously not been available. One of these features is the ability to adjust the Initial volume level.
  • Page 12 MODE pushbutton or wait for approx. 12 seconds to exit the MODE menu. 4.5 Unity Gain This setting option will by-pass the volume control of a chosen input. This feature is useful Energy if integrating the into a multichannel system. MONO...
  • Page 13: Factory Default Settings

    4.6 Input level adjustments Energy It can be that the various sources connected to the have different output levels. This is usually noted when switching inputs and noticing that different sources Energy play at more loudly than others. The offers the option to adjust the sensitivity for each input.
  • Page 14: What To Do, If

    10 whereas all input level adjustments are changed to "zero , and the PRE-OUT (preamplifier output) is available. Energy All of your settings will be lost! The will be reset to the Factory Default settings.
  • Page 15: There Is A Hum

    This charge can be transmitted to the preamplifier during normal use and Energy may confuse the microprocessor used to control the . This is a common Energy problem with many common computers as well.
  • Page 16: Technical Data

    Size (WxHxD) : 440 x 85 x 360 mm (WxHxD) Warranty : 3 Years Specifications subject to change. Designed and Manufactured by: TRIGON ELEKTRONIK GmbH Korbacher Straße 185 D-34132 Kassel Tel. +49 (0) 561/47 44 62 +49 (0) 561/47 44 63 Email trigon@trigon-audio.de...

Table of Contents