Setting The Bass Control; Setting The Treble Control - Alpine CDA-9852RB Owner's Manual

Setting the Bass Control

You can change the Bass Frequency emphasis to create your own tonal
preference.
1
Press MENU to select the BASS ENGINE mode, then
press MODE.
BASS ENGINE SETUP
2
Press or to select the BASS (bass Centre
frequency) control mode.
BASS TREBLE
Setting the Bass Centre Frequency
3
-1 Press SOURCE/POWER to select the desired bass
centre frequency.
80Hz 100Hz 120Hz
Emphasizes the displayed bass frequency ranges.
Setting the Bass Bandwidth
3
-2 Press BAND to select the desired bass bandwidth.
(Narrow)
Changes the boosted bass bandwidth to wide or narrow. A
wide setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.
Setting the Bass Level
3
*1
-3 Turn the Rotary encoder to select the desired
bass level (–7~+10).
You can emphasize or weaken the bass
4
Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
• If no operation is performed within 60 seconds, the bass control
setting will be turned off automatically.
• The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass band width settings adjusted for one source
are effective for all other sources (FM, MW (LW), CD etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, Bass Level is still adjustable if an
audio processor with the Bass function is connected.
• This function is inoperable when DEFEAT is set to ON.
• If you press or in the bass control mode, the unit
changes to the treble control mode.
1
* The adjustment can also be made by pressing MODE. Refer to
"Adjusting Bass/Treble/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat" (page 14).
RETURN (OFF) BASS ENGINE
60Hz 80Hz
(Wide)
.
level
Bass level indicator's display

Setting the Treble Control

You can change the Treble Frequency emphasis to create your own tonal
preference.
1
Press MENU to select the BASS ENGINE mode, then
press MODE.
BASS ENGINE SETUP
2
Press or to select the TREBLE (treble
Centre frequency) control mode.
BASS TREBLE
Setting the Treble Centre Frequency
3
-1 Press SOURCE/POWER to select the desired treble
Centre frequency.
10.0kHz 12.5kHz 15.0kHz
Emphasizes the displayed Treble frequency ranges.
Setting the Treble Level
3
*2
-2 Turn the Rotary encoder to select the desired
treble level (–7~+7).
You can emphasize the treble
4
Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
• If no operation is performed within 60 seconds, the treble control
setting will be turned off automatically.
• The treble level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for all
other sources (FM, MW (LW), CD, etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, Treble Level is still adjustable if
an audio processor with the Treble function is connected.
• This function is inoperable when DEFEAT is set to ON.
• If you press or in the treble control mode, the unit
changes to the bass control mode.
2
* The adjustment can also be made by pressing MODE. Refer to
"Adjusting Bass/Treble/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat" (page 14).
Bass level is usually displayed.
RETURN (OFF) BASS ENGINE
7.5kHz 10.0kHz
.
level
15
-EN