Genelec 1032A Operating Manual page 4

Figure 5. The curves above left show the effect of the 'bass tilt',
'bass level' and 'bass roll-off' controls on the free field response. The
curves to the right show the effect of the treble and midrange 'level'
controls.
SYSTEM SYSTEM
SYSTEM SYSTEM SYSTEM
SPECIFICATIONS SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS
Lower cut-off frequency, -3 dB: <40 Hz
Upper cut-off frequency, -3 dB: >22 kHz
Free field frequency response
of system: 42 Hz - 21 kHz (±2.5 dB)
Maximum short term sine wave acoustic
output on axis in half space, averaged from
100 Hz to 3 kHz: @1m >113 dB SPL
@0.5m >119 dB SPL
Maximum long term RMS acoustic output in
same conditions with IEC-weighted noise
(limited by driver unit protection circuit):
@1m >103 dB SPL
@0.5m >109 dB SPL
Maximum peak acoustic output per pair on
top of console, @ 1m from the engineer
with music material: >124 dB SPL
Self generated noise level in free field @ 1m
on axis: <10 dB
(A-weighted)
Harmonic distortion at 95 dB SPL at 1m on
axis:
50Hz...100 Hz
freq. >100 Hz
Drivers: Bass 10" (250 mm)
Treble 1" (25 mm) metal dome
Both drivers are magnetically shielded.
Weight: 21,7 kg (48 Ib.)
Dimensions: Height 495 mm (19
Width 320 mm (12
Depth 290 mm (11
Genelec Oy, Olvitie 5 Genelec Oy, Olvitie 5 Genelec Oy, Olvitie 5 Genelec Oy, Olvitie 5 Genelec Oy, Olvitie 5
FIN - 74100 IISALMI, FINLAND FIN - 74100 IISALMI, FINLAND FIN - 74100 IISALMI, FINLAND
FIN - 74100 IISALMI, FINLAND FIN - 74100 IISALMI, FINLAND
Phone: Phone: Phone: Phone: Phone: +358 - 17 - 83 881 +358 - 17 - 83 881 +358 - 17 - 83 881 +358 - 17 - 83 881 +358 - 17 - 83 881
F F F F F ax: ax: ax: ax: ax: +358 - 17 - 812 267 +358 - 17 - 812 267 +358 - 17 - 812 267 +358 - 17 - 812 267 +358 - 17 - 812 267
E-mail: E-mail: genelec@genelec.com genelec@genelec.com
E-mail: E-mail: E-mail: genelec@genelec.com genelec@genelec.com genelec@genelec.com
Web: Web: Web: Web: Web: http://www.genelec.com http://www.genelec.com http://www.genelec.com http://www.genelec.com http://www.genelec.com
Bass amplifier output power with a 4 Ohm
load:
Treble amplifier output power with a 8
Ohm load:
Long term output power is limited by
driver unit protection circuitry.
Slew rate :
Amplifier system distortion at
nominal output: THD
Signal to Noise ratio, referred to full output:
Mains voltage:
Voltage operating range at 115V setting:
Power consumption:
<1%
<0.5%
1
/ ")
2
5 / ")
8
7 / ")
16
Genelec Inc, 7 Tech Circle Genelec Inc, 7 Tech Circle Genelec Inc, 7 Tech Circle Genelec Inc, 7 Tech Circle Genelec Inc, 7 Tech Circle
Natick, MA 01760, USA Natick, MA 01760, USA Natick, MA 01760, USA
Natick, MA 01760, USA Natick, MA 01760, USA
Phone: Phone: Phone: Phone: Phone: +1 - - - - - 508/652-0900 +1 +1 +1 +1 508/652-0900 508/652-0900 508/652-0900 508/652-0900
Fax: Fax: Fax: Fax: Fax: +1 - - - - - 508/652-0909 +1 +1 +1 +1 508/652-0909 508/652-0909 508/652-0909 508/652-0909
E-mail: E-mail: E-mail: E-mail: E-mail: genelec.usa@genelec.com genelec.usa@genelec.com genelec.usa@genelec.com genelec.usa@genelec.com genelec.usa@genelec.com
Figure 6. The upper curve group shows the horizontal directivity
characteristics of 1032A in its vertical configuration measured at 1m.
The lower curve is a 1/3 octave band power response, measured in
an IEC approved reverberation chamber.
AMPLIFIER AMPLIFIER AMPLIFIER AMPLIFIER AMPLIFIER
SECTION SECTION SECTION SECTION SECTION
Short term 180 W
Short term 120 W
80V/µs
<0.05%
SMPTE-IM <0.05%
CCIF-IM <0.05%
DIM 100 <0.05%
Bass >100 dB
Treble >100 dB
100/200V or 115/230V
104 - 126V (±10%)
Idle 50W
Full output 200W
CROSSOVER CROSSOVER
CROSSOVER CROSSOVER CROSSOVER
SECTION SECTION
SECTION SECTION SECTION
Input connector: XLR female
Input impedance: 10 kOhm
Input level for 100 dB SPL output @1m:
variable from +6 to -6 dBu
Input level for maximum short term output
of 113 dB SPL @1m:
variable from +19 to +7 dBu
Subsonic filter below 40 Hz :
18 dB/octave
Ultrasonic filter above 25 kHz:
12 dB/octave
Crossover frequency: 1.8 kHz
Crossover acoustical slopes:
24 - 32 dB/octave
Treble tilt control operating range in 2dB
steps: from+2 to -4dB & MUTE
Bass roll-off control in 2 dB steps:
from 0 to -8 dB
Bass tilt control in 2 dB steps:
from 0 to -8 dB
The 'CAL' position is with all tone controls
set to 'off' and input sensitivity control to
maximum.
Note! All frequency response curves were measured in a Note! All frequency response curves were measured in a Note! All frequency response curves were measured in a
Note! All frequency response curves were measured in a Note! All frequency response curves were measured in a
calibrated, 12 m cube, anechoic chamber at 1 m using grade 1 calibrated, 12 m cube, anechoic chamber at 1 m using grade 1 calibrated, 12 m cube, anechoic chamber at 1 m using grade 1 calibrated, 12 m cube, anechoic chamber at 1 m using grade 1 calibrated, 12 m cube, anechoic chamber at 1 m using grade 1
measuring equipment. Input signal levels were set at -20 dBu. measuring equipment. Input signal levels were set at -20 dBu. measuring equipment. Input signal levels were set at -20 dBu. measuring equipment. Input signal levels were set at -20 dBu. measuring equipment. Input signal levels were set at -20 dBu.
The anechoic chamber error in the free field response is less The anechoic chamber error in the free field response is less The anechoic chamber error in the free field response is less The anechoic chamber error in the free field response is less The anechoic chamber error in the free field response is less
than 0.5 dB down to 60 Hz. than 0.5 dB down to 60 Hz. than 0.5 dB down to 60 Hz. than 0.5 dB down to 60 Hz. than 0.5 dB down to 60 Hz.
Genelec document DR32001
COPYRIGHT GENELEC OY 6/1999
All data subject to change without prior notice
pin1 gnd
pin2 +
pin3 -
@40 Hz
@80 Hz