Table of Contents
Advertisement
Instructions for use
GB
English,1
BHWMD 732
WASHING MACHINE
Contents
Installation, 2-3-4-5-6-7
Connecting the electricity and water supplies
Detergent dispenser drawer
Cutting off the water or electricity supply
Troubleshooting, 15-16
Assistance, 17
GB
1
Advertisement
Table of Contents
Related Manuals for Hotpoint BHWMD 732
Summary of Contents for Hotpoint BHWMD 732
-
Page 1: Table Of Contents
Control panel Display Running a wash cycle, 10 Wash cycles and functions, 11 Table of wash cycles Wash functions BHWMD 732 Detergents and laundry, 12 Detergent dispenser drawer Preparing the laundry Special wash cycles Load balancing system Precautions and tips, 13... -
Page 2: Unpacking And Levelling
Installation 2. If the floor is not perfectly level, compensate for any Keep this instruction manual in a safe place for future referen- unevenness by tightening or loosening the adjustable front ce. Should the appliance be sold, transferred or moved, make feet (see figure);... -
Page 3: Electric Connection
Connecting the drain hose • the supply voltage is included within the values indica- ted on the Technical Data Plate fixed on the machine. Connect the drain hose, without bending it, to a • the socket is compatible with the washing machine’s draining duct or a wall drain plug. -
Page 4: The First Wash Cycle
The first wash cycle As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Once the appliance has been installed, and before you use Connect Green & Yellow wire to terminal marked E or it for the first time, run a wash cycle with detergent and no or coloured Green or Green &... -
Page 5: Technical Data
Technical data Model BHWMD 732 width 59.5 cm Dimensions height 81.5 cm depth 54.5 cm Capacity from 1 to 7 kg Electrical please refer to the technical data plate fixed to the machine connections maximum pressure 1 MPa (10 bar) Water connections minimum pressure 0.05 MPa (0.5 bar) -
Page 6: Instructions For The Fitter
Instructions for the fitter Door Mounting Accessories (Fig. 1-2-3-4-5). Mounting the wooden panel onto the door and in- serting the machine into cabinets: In the case where the machine must be shipped for final installation after the wooden panel has been mounted, we suggest leaving it in its original packaging. - Page 7 Using the Drilling Template. - To trace the positions of the holes on the left-hand side of the panel, align the drilling template to the top left side of the panel using the lines traced on the extremities as a referen- - To trace the positions of the holes on the right-hand side of the panel, align the drilling template to the top right side of the panel.
-
Page 8: Description Of The Washing Machine
Description of the washing machine Control panel ON/OFF CHILD LOCK SPIN SPEED button button button DISPLAY MY CYCLE button WASH FUNCTION CYCLE START/PAUSE buttons DELAY SELECTOR Detergent dispenser drawer button with TIMER buttons indicator light TEMPERATURE button button Detergent dispenser drawer: used to dispense deter- CHILD LOCK button: to activate the control panel lock, gents and washing additives (see “Detergents and laundry”). -
Page 9: Display
Display The display is useful when programming the machine and provides a great deal of information. The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa- tion relating to the progress status of the wash cycle. String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the time remaining until the start of the selected wash cycle. -
Page 10: Running A Wash Cycle
Running a wash cycle 1. SWITCH THE MACHINE ON. Press the On/Off 7. START THE PROGRAMME. Press the START/ button ; the text HELLO will appear on the display PAUSE button. The corresponding indicator light will and the START/PAUSE indicator light will flash slowly in become green, remaining lit in a fixed manner, and the a green colour. -
Page 11: Wash Cycles And Functions
Wash cycles and functions Table of wash cycles Detergents Max. Max. Description of the wash cycle temp. speed Wash Fabric (°C) (rpm) softener CLEAN Plus Anti Stain 40° 1300 180’ White Cottons : extremely soiled whites and resistant colours. 90°... -
Page 12: Detergents And Laundry
Do not use hand washing detergents because these such as pollen, mites, cat’s and dog’s hair. create too much foam. Wool: the wool wash cycle on this Hotpoint machine has been tested and approved by The Woolmark Company Open the detergent di-... -
Page 13: Precautions And Tips
Precautions and tips Opening the porthole door manually This washing machine was designed and constructed in accordance with international safety regulations. The fol- In the event that it is not possible to open the porthole lowing information is provided for safety reasons and must door due to a powercut, and if you wish to remove the therefore be read carefully. -
Page 14: Care And Maintenance
Care and maintenance Cutting off the water and electricity To access the pre-chamber: supplies 1. unscrew the lid by rota- ting it anti-clockwise (see • Turn off the water tap after every wash cycle. This will limit figure): a little water may wear on the hydraulic system inside the washing machine trickle out. -
Page 15: Troubleshooting
Troubleshooting Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list. Problem: Possible causes / Solutions: The machine does not switch on. •... - Page 16 The machine is noisy. • There will always be some motor, pump and drum noise during spin. The machine wont spin properly. • Out of Balance detected when attempting to go into a spin cycle - If this happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds - This will increase the programme time accordingly.
-
Page 17: Assistance
Assistance Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. - Page 20 195102743.01 05/2012 - Xerox Fabriano...