Srm450 Specifications - Mackie SRM450 V2 User Manual

SRM450 SPECIFICATIONS

System Specifications
Frequency Response (–3 dB)
55 Hz – 18 kHz
Frequency Range (–10 dB)
45 Hz – 0 kHz
Directivity Factor; Q (DI) 9.95 (9.98), averaged  kHz to 10 kHz
Max SPL Long-term @ 1m
14 dB
Max SPL Peak @ 1m 17 dB
Crossover Linkwitz-Riley,
4 dB/octave @ 1600 Hz
Audio
Input Type Balanced Differential
Input Impedance 0 kohms
Input Protection RFI and level protected
Sensitivity
Line: +4 dBu (center detent)
Mic: –6 dBu
Maximum Input Level + dBu
Low-Cut Frequency 75 Hz, Second-order filter
Acoustic Contour Equalization
Peaking: + dB @ 100 Hz,
+ dB @ 1 kHz
Operating Temperature Range
–10ºC to 45ºC (14ºF to 11ºF)
Power Amplifiers
Low-Frequency Power Amplifier
Rated Power 00 watts*
Rated THD < 0.1%
Cooling Convection Extrusion
Design Class D, Parametric Servo Feedback
High-Frequency Power Amplifier
Rated Power 100 watts*
Rated THD < 0.1%
Cooling Convection Extrusion
Design Conventional Class AB
*Rated power is continuous rms wattage into transducer's rated impedance @ 5 kHz
for the HF amplifier and @ 500 Hz for the LF amplifier.
Transducers
Low-Frequency Transducer
Diameter 1 in/00 mm
Voice Coil Diameter .0 in/75 mm
Sensitivity (1W@1m) 98 dB
Nominal Impedance 8 ohms
Power Handling 600 watts, program
45 Hz –  kHz
Frequency Range
High-Frequency Transducer
Diaphragm Diameter 1.75 in/44.5 mm
Heat treated titanium
Diaphragm Material
Sensitivity (1W@1m) 106 dB
Nominal Impedance 8 ohms
Power Handling 100 watts, program
Frequency Range 1 kHz – 0 kHz
Horn Design
Type Conical and Exponential
Mouth Size 1 in/04.8 mm (W) x 7 in/177.8 mm (H)
Throat Diameter 1 in/5.4 mm
Horizontal Coverage 90º (1 kHz–0 kHz)
45º (.8 kHz–0 kHz)
Vertical Coverage
Line Input Power
US 10 VAC, 60Hz
Recommended amperage service .5 amps
Europe 0 VAC, 50Hz
Recommended amperage service 1.5 amps
100 VAC, 50/60Hz
Japan
Recommended amperage service .0 amps
AC Connector -pin IEC 50 VAC
Control System Function
Electronic Crossover
Phase Alignment
Equalization
Parametric Equalization
Safety Features
Over-Excursion Protection
Second-Order High-Pass Filter
Thermal Protection Amplifier shutdown, auto-reset
Low-Line Voltage Shut Down
60% Nominal line
Driver Protection Independent LF and HF compressors
Low-Freq Roll-Off Dynamic, signal-level dependent
Construction Features
Basic Design Asymmetrical Trapezoidal
Enclosure Alignment Sixth-Order
Material Polypropylene
Finish Midnight Blue, textured finish
Handles One on each side, one on top
Mounting Methods
Integrated mounting points, M10
Two each located on each side, top, bottom, and
rear of enclosure
Grille Perforated metal with weather-resistant coating
Display LEDs Signal Present, Peak, Power ON, and Thermal
Physical Properties
6.0 in/660 mm
Height
Width 15.4 in/90 mm
Depth 14.8 in/76 mm
Weight 40 lb/18 kg
Options
PA-A1 forged shoulder eyebolt hardware (M10 x 1.5 mm x 0 mm)
SPM100 (Speaker Pole Mount)
Disclaimer
Since we are always striving to make our products better by incor-
porating new and improved materials, components, and manufacturing
methods, we reserve the right to change these specifications at any time
without notice.
"Mackie.," the "Running Man" figure, and "FR Series" are registered
trademarks of LOUD Technologies Inc.
All other brand names mentioned are trademarks or registered
trademarks of their respective holders, and are hereby acknowledged.
©00-008 LOUD Technologies Inc.
All Rights Reserved.
R
17