Video Setup - Denon DBP-4010UD Owner's Manual

ENGLISH
HDMI Setup
Setting items
Audio Setup GMulti LPCM BM OffH : Decoded Linear PCM multi-channel signal is
output by the DBP-4010UD. This setting is not made in speaker setting.
(BM: Bass Management)
G2ChH : Output the downmixsed 2-channel LPCM signal.
GMuteH : Do not output audio from HDMI.
SA-CD Audio Out On : Super Audio CD audio is output.
Set to output stereo/multi Off : Super Audio CD audio is not output.
area audio of Super Audio
CD to the HDMI terminal.
The Super Audio CD audio signal is a 44.1 kHz/16-bit Linear PCM output.
HDMI Control
GControlH
Can operate the unit in • Off : Disable the HDMI control function.
conjunction with an HDMI On : Link with the device connected to HDMI.
•
control support device.
GPower Off ControlH
• On : Turns the DBP-4010UD's power to standby through linkage to the
TV.
Off : Does not turn the DBP-4010UD's power to standby through linkage
•
• For the HDMI control function to operate, it is necessary for the DBP-
4010UD or HDMI-compatible TV connected to the DBP-4010UD to have
an HDMI connection.
• Refer to "HDMI Control Function" (vpage 47) for more information
about the HDMI control function.
• The HDMI control function from the connected device becomes valid
when, on the GUI menu, "DENON LINK Setup" – "DENON LINK Mode"
is set to "4th" (vpage 28).
• After the "HDMI Control" setting has been changed, always turn off the
power to the connected equipment and then turn it back on.
NOTE
If you set "DENON LINK Setup" – "DENON LINK Mode" on the GUI menu to "4th", you will no longer
be able to change the "HDMI Control" – "Control" setting. To change the setting, switch "DENON LINK
Mode" to a setting other than "4th" fi rst and then change the setting.
Remote control operation
2 buttons
Setting contents
to the TV.
: Displaying the menu
Cancel the menu

Video Setup

Set the video output signal according to the connected TV.
Setting items
TV Aspect (Aspect ratio) 16:9 Squeeze Auto : Output to a wide screen TV. For 4:3 video, display in
Set the screen type and the center of the screen without changing the aspect ratio. z1
display mode of the TV. WIDE (16:9) : Output to a wide screen TV.
4:3 PS : Output to a 4:3 TV. For wide video, trim the left and right side of
the image and display in 4:3 aspect ratio. z2
4:3 LB : Output to a 4:3 TV. Display all of the wide video.
480/576i, 480/576P, 720P, 1080i,
Component Resolution z3
Source Direct : Output video using its source resolution. Convert the
Set the component output
1080p video source to 1080i.
resolution.
Progressive Mode Auto : Detect the type of video material and automatically switch the
Set an appropriate mode. Normally, this setting is used.
progressive conversion Video1 : Suitable for playing video material discs.
Video2 : Suitable for playing video material discs or 30-frame fi lm material
mode for the source video
material. discs.
TV Active Area Full : Set when a home-use monitor is connected.
Sets the horizontal display Normal : This setting is used when video synchronization is disturbed on
range when the analog a professional-use monitor.
video output resolution is
480i/576i.
z1 : This has no effect with the video and S-Video outputs.
z2 : Depending on the video content, even though you set the 4:3 PS ( P an Scan), the content may be
output in 4:3 LB ( L etter Box).
z3 : When video is output from the HDMI terminal, no video signals are output from the component
terminals.
: Moves the cursor
:Decision the setting
(Up/Down/Left/Right)
Default settings are underlined.
Setting contents
This is not available for HDMI output.
:Return to previous menu