Denon DBP-1611UD Service Manual

Universal audio/video player

Hide thumbs Also See for DBP-1611UD:

Specifications (2 pages)

Specifications (2 pages)

Owner's manual (70 pages)

Table Of Contents

Table of Contents

Quick Links

Need help?

Do you have a question about the DBP-1611UD and is the answer not in the manual?

Questions and answers

Summary of Contents for Denon DBP-1611UD

Page 1 Ver. 7 P e se refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E2R EUT DBP-1611UD P P P P P P UNIVERSAL AUDIO VIDEO PLAYER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set. D M oldings Inc. S0309-1V07DM D 1106...
Page 2: Safety Precautions
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
Page 3 NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
Page 4 WARNING AND LASER SAFETY INSTRUCTIONS WARNING WAARSCHUWING Alle IC’s en vele andere halfgeleiders zijn gevoelig All ICs and many other semi-conductors are voor elektrostatische ontladingen (ESD). susceptible to electrostatic discharges (ESD). Onzorgvuldig behandelen tijdens reparatie kan de Careless handling during repair can reduce life levensduur drastisch doen verminderen.
Page 5 INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M ) that is properly grounded to remove any static electricity that may be charged on the body. 2.
Page 6 TEC NICAL SPECIFICATIONS n Audio perfor Audio output characteristics : (1) Frequency response Signal format : NTSC, PAL q BD (Linear PCM) : 2Hz ~ 22kHz (48kHz sampling) Applicable discs /memory device : : 2Hz ~ 44kHz (96kHz sampling) (1) BD-Video disc : : 2Hz ~ 88kHz (192kHz sampling) 12 cm, 1 side, 1 layer;...
Page 7 CAUTIONS IN SERVICING Initi i in BD p BD player initiali ation should be performed when the com, peripheral parts of com, and MAIN P.W.B. were replaced. 1. Turn on this model s power. "NO DISC" is displayed on the FL tube. 2. P ress the this model s 2 and DISC LAYER buttons simultaneously. "INITIALI IN " is displayed on the FL tube. 3. T he display on the FL tube switches to "INITIALI ED", the "NO DISC" display reappears and initiali ation is completed. Note •If step 3 does not work, start over from step 1. • A ll user settings will be lost and this factory setting will be recovered after the set is initiali ed. So make sure to note down your setting beforehand for restoring after the initiali ation. DISC LAYER ON STANDBY Ser ice too s...
Page 8 DISASSEMBLY f • Disassemble in order of the arrow in the following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling". • I f wire bundles are untied or moved to perform adjustment or replace parts etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. TOP COVER FRONT PANEL ASSY REMOTE PWB UNIT Refer to "DISASSEMBLY Refer to "DISASSEMBLY Refer to "DISASSEMBLY 1. FRONT PANEL ASSY" 3. REMOTE PWB UNIT" 4. FAN" and "EXPLODED VIEW" and "EXPLODED VIEW"...
Page 9 1. FRONT PANEL ASSY Proceedin TOP COVER FRONT PANEL ASSY → (1) Detach the LOADER PANEL. Shooting direction: B (2) Disconnect the connector wire and FFC cable. FFC cable (3) Lift up to unhook the claw and move in the direction of arrow to gradually pull out the assembly. Shooting direction: C Shooting direction: D View from the bottom Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY.
Page 10 2. BD MAIN UNIT ASSY s Proceedin TOP COVER FRONT PANEL ASSY BD MAIN UNIT ASSY → → (1) Disconnect the connector wires and FFC cables, then remove the screws. FFC cable BD MAIN UNIT ASSY POWER PWB UNIT FFC cable BAC PANEL ASSY (2) Remove the screws. Shooting direction: A (3) Remove the screw. View from the bottom...
Page 11 (4) Remove the screws, then remove the BD MAIN UNIT. BD MAIN UNIT ASSY POWER PWB UNIT BAC PANEL ASSY Please refer to "EXPLODED VIEW" for the disassembly method of MAIN P.W.B included in BD MAIN UNIT 3. REMOTE PWB UNIT Proceedin TOP COVER → REMOTE PWB UNIT Please refer to "EXPLODED VIEW" for the disassembly method of IR PWB UNIT. 4. FAN Proceedin TOP COVER → Please refer to "EXPLODED VIEW" for the disassembly method of FAN. 5. POWER PWB UNIT Proceedin TOP COVER → → POWER PWB UNIT Please refer to "EXPLODED VIEW" for the disassembly method of POWER PWB UNIT.
Page 12 REMOVING DISCS (1) Remove the Top Cover. (2) Open the CD tray by turning the Drive gear counterclockwise. Drive gear Shooting direction: D...
Page 13 DIAGNOSTICS OF OPTICAL PIC UP d Make failure diagnostics of the Optical Pickup as follows. q If the laser drive current (Iop) becomes more than BD : 6 mA , DVD or CD : 12 mA of the initial value, the Optical Pickup should be replaced. The laser drive current initial value is checked by "Iop checked Method" of ne t page. w L oad five times of following disc again and playing it for one minute. It becomes the aim of the Optical Pickup e change when it cannot play. BD-RE ABD-RE 40W(made by ALMEDIO) In case of replacing the Pickup, change the whole part of the BD MAIN UNIT (including the MAIN PWB UNIT) or BD MEC A UNIT ASSY. No mechanical adjustment is necessary after the replacement. ( OW TO REPACE T E BD MAIN UNIT OR T E BD MEC A UNIT ASSY (page 1 )) L ser dri e current initi FL Display (The display part of 13 digits) CD : T 2 1 : m m m m : n n n n...
Page 14 1. Iop chec ed Method Select the laser ON OFF(CD DVD BD)mode of the test mode, and check the Iop value of CD laser, DVD laser or BD laser. (Refer to "6. Test mode") FL Display (The display part of 13 digits) L a s e r O n O f f L ser current chec Press the 8 or 9 button to display the laser current value, and then select X . Check the current value of Iop (nnnn) FL Display (The display part of 13 digits) T 2 X : m m m m : n n n n (X 1 : CD laser mode, 2 : DVD laser mode, 3 : BD(SL) laser mode (mmmm mA : Initial value, nnnn mA : Current value) 2.
Page 15 OW TO REPLACE T E BD MAIN UNIT OR BD MEC A UNIT ASSY f NOTE The i ht pic up ser diode LD is inst nt de r ded or d ed b st tic e ectricit or po er sur e. When h nd in the BD MEC A UNIT s be sure to e rth ourse f nd use n e rth...
Page 16 Connection (1) Connect the PC and bar code reader. (2) C onnect the 232C (TTL) side 4P P connector of the USB - 232C (TTL) conversion jig to the MAIN PWB UNIT (CON601) of the set. (3) Connect the USB side of the USB - 232C (TTL) conversion jig to the PC. PC (USB)へ USB - 232C(TTL) conversion sig MAIN PWB UNIT CON601 4P RE-P CONN CORD (1000mm) umper pin : 3.3V f mark Writin ne i ht pic up d t • Barcode position of light pick-up unit BD MEC A UNIT ASSY for replacement 2-Dimensional Bar Code (The 2-dimensional bar code can be photographed with a digital camera, and the barcode data can be converted with a 2-dimensional barcode reader.) View from the bottom (1) Switch on the power on of the set before the BD MEC A UNIT ASSY is replaced. (2) Decompress the D M ScanBarcode Rpower 2.16.60( ES460) MP function. ip folder and start the "Rpower.e e". (3) A pop-up is displayed. Click "O ".
Page 17 ( ) O n the screen below, select "ComPort XX". Select the USB - 232C (TTL) conversion jig port. (6) C heck "Directly".
Page 18 (7) C lick the left edge of the "Bar Code" window, and the cursor begins to flash. Click (8) P lace the bar code reader over the bar code attached to the replacement BD MEC A UNIT ASSY. When the reader has finished reading the barcode, the read data is displayed. b I f the 2-dimensional barcode data has already been read by the 2-dimensional barcode reader, and the converted data obtained, copy the data from the data file, and paste it into this section. NOTE Be sure not to e the i ht pic up b r code d t settin s ith d t fro different pic up. Writin incorrect d t i c use ser de r d tion.
Page 19 (9) C lick Write(F2). (10) W hen Pass changes to green, writing to the Flash ROM of the MAIN PWB UNIT is complete. (11) S witch off the set unit power, and remove the 232C (TTL) side 4P P connector of the USB - 232C (TTL) conversion jig from the MAIN PWB UNIT (CON601).
Page 20 2.4. Rep ce the BD MEC A UNIT ASSY (1) Remove the old BD MAIN UNIT from the set unit (see "DISASSEMBLY"). (2) Remove the MEC A COVER. DRIVE MEC A UNIT TOP COVER (3) Disconnect the connector wire and FFC cable. MAIN PWB UNIT FFC cable A700 (4) Move the optical pickup to the outer circumference, remove the FFC Cable, and remove the screws. OPTICAL PIC UP FFC cable...
Page 21 ( ) A ttach the BD MEC A UNIT ASSY for replacement to the set unit. (When assembling the unit, perform the steps in reverse order.) (6) Check that the 4 P-FFC, 9P-FFC and P-P connector cords have been connected. 2.4. Con ure the settin s of the set th t cont ins the ne BD MEC A UNIT (1) C heck the laser amperage (see laser on off mode in the test mode (page 2 )). Check that the values are 6 mA from the initial value for BD, and 12 mA from the initial value for DVD CD. (2) C lear the total laser usage time (see the procedure for clearing the accumulated laser on time in test mode (page 26)).
Page 22 SERVICE MODE 1. Initi settin 1.1. prep r tion (1) E uipment used: None (2) U nit setting: No spec other than the following procedure. 1.2. procedure b I nitiali e the BD player when com, peripheral parts of com, or MAIN P.W.B. unit has been replaced in servicing. b A ll user setting will be lost and its factory setting will be restored when this initiali ation is made. Be sure to memori e your setting for restoring again after the initiali ation. (1) T urn on this model s power. "NO DISC" is displayed on the FL tube. (2) P ress the this model s 2 and DISC LAYER buttons simultaneously. "INITIALI IN " is displayed on the FL tube. (3) T he display on the FL tube switches to "INITIALI ED", the "NO DISC" display reappears and initiali ation is completed.
Page 23 (1) E uipment used: None (2) U nit setting: No spec other than the following procedure. 4.2. procedure Settin (1) P ressing the PURE DIRECT and 3 buttons for simultaneously. (2) Lock-On is displayed on the FL tube, and operations with the remote control and the REMOTE CONTROL input terminal on the back of the DBP-1611UD are disabled. C nce (1) P ressing the PURE DIRECT and 3 buttons for simultaneously. (2) " Lock-Off" is displayed on the FL tube and remote lock mode is made canceled. 5. A Lit A Off ode for the FL tube 5.1. prep r tion (1) E uipment used: None (2) U nit setting: No spec other than the following procedure.
Page 24 . Test ode f .1. Enterin the test The test mode is entered by pressing the 5 and 3 buttons simultaneously, plug the AC cord into a power outlet. When the test mode is set, the " 1 " and " 3 " indicators light. FL tube display when test mode entered FL Display (The display part of 13 digits) When the test mode is set, the choice screen of the mode appears on the monitor. .2. Se ectin the ・ The following modes are available. (1) Laser on off (CD DVD BD) mode : T2 (2) Error rate (skew) measurement mode : T7 (3) Accumulated laser on time display mode : TC (4) Picking up No. display mode : T ( ) Test mode cancel : TI...
Page 25 .3. About e ch ・ With the mode selected, press the 1 button to set that mode. (1) Laser on off (CD DVD BD) mode Press the 8 or 9 button to select X and press the 1 button to set it. Laser on off control is e ecuted and the laser current is displayed. FL Display (The display part of 13 digits) (X 1 : CD laser mode, 2 : DVD laser mode, 3 : BD(SL) laser mode) (mmmm mA : Stored data, nnnn mA : Current value) b When the current value is more that BD: 6 mA , DVD or CD: 12 mA of saved data, it becomes the pickup transducer s target.
Page 26 (3) Accumulated laser on time display mode Press the 8 or 9 button to select Y and press the 1 button to set it. The accumulated laser on time is displayed. FL Display (The display part of 13 digits) (Y 1 : CD, 2 : DVD , 3 : BD, mmmmmm : Time(Fractions of hours are counted up one hour on the display.) When the 2 button is pressed, the layer above the current layer is displayed. See "6.4 Stopping the mode". To c e r the ccu u ted ser on ti e Press the 1 button while the accumulated laser on time is displayed ("TC1, "TC2", "TC3" ) until "TC4 ＊ clear " appears at the display. FL Display (The display part of 13 digits) If the 1 button is pressed, the accumulated laser on time of CD, DVD and BD is cleared. FL Display (The display part of 13 digits) When "TC1", "TC2" or "TC3" is selected with the 8 or 9...
Page 27 .4. Stoppin the When the 2 button is pressed, the layer above the current layer is displayed. The relationship between the different modes and the display of the different layers is shown on the table below. Mode Laser on off (CD DVD BD) mode T2 LaserOnOff T2X mmmm nnnn Error rate measurement mode T7 Error Rate TYYFFFFFFFFFF TYYmmmmmmllll Accumulated laser on time display mode TC LaserOnTim TCY mmmmmmh TC4* clear Picking up No. display mode T OPU Number T X YYYYYYY Test mode cancel TI Test E it TI1 Really .5. About the OPEN CLOSE 5 button Even during the test mode, the tray is opened and closed when the 5 button is pressed. .
Page 28 Error r te disp det i s for e ch edi t pe Me sure ent position The inner It is invalid. It is invalid. It is invalid. When this is selected for BD, DVD or circumference of CD, T84 FFFFFFFFFF display. 2-layer The inner LDC error detection PI error detection It is invalid. When this is selected for 1-layer DVD circumference of signed number number or CD, T8 FFFFFFFFFF display. 2-layer The inner It is invalid. It is invalid. It is invalid. When this is selected for BD, DVD or circumference of CD, T86 FFFFFFFFFF display.
Page 29 PROCEDURE FIRMWARE FOR UPGRADING T E VERSION OF T E FIRMWARE f You can update by downloading the latest version from the Internet. 1. Upd te fro the Internet 1.1. prep r tion (1) System re uirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT- or greater recommended) (2) Setting Internet Computer Modem LAN port Ethernet connector To WAN port Router...
Page 30 TROUBLE S OOTING 1. POWER UNIT The power cannot be turned on. Defect of primary circuit component. ・ BD1 (RBV1 06) ・ IC1 (STR-W67 3) N.G. ・ U (STR-A60 9 ) Check the FUSE condition. ・FUSE ・ T1 (EER28(SW TRANS)) F101 ・ T2 (EI16(SW TRANS)) and other circuits. O. . Check parts and soldering.
Page 31 2. DISPLAY UNIT 2.1. FL TUBE doesn t light. Check parts (surrounding) and soldering. ・ U3 (MR-662 UYB) N.G. POWER UNIT Check F output.（4.8V）・ T1 (EER28(SW TRANS)) ( 1 14- 16) ・ D19 (FR307) ※ 4.32V 〜 .28V ・ 1 (20 1 W OUSIN ) and other circuits. O.
Page 32 3. MAIN UNIT 3.1 Video out doesn t output. Check soldering. N.G. ・U18 (N M2 66AV) and surrounding circuits. Check the input signal to U18 . ・Y6 (U18 6pin) ・ C 44 ・ R 67 R 71 O. . Check the power supply and control signal for U18 . ・ V AV (U18 3pin) ・V MUTE (U18 1pin) N.G. Check the output signal to U18 . Check soldering.
Page 33 3.3. Analog audio doesn t output. Check the power supply voltage for U801 . N.G. ・ 12V (U801 8pin 11V Upper) Check the POWER UNIT. ・-12V (U801 4pin -12V Low） O. . Check the input and output voltage for U702 . N.G. Check the power supply voltage for U802 . Check soldering. ・ V(U802 11pin) ・U702(N M78M0 ) CE20 C88 O. . Check soldering. Check the audio output for U801 . N.G. ・ U801 C 39 R967 R963 C967 R9 6 R964 ・Lch(U801 1pin) C964 C 40 R968 R96...
Page 34 3.4 Digital Out(COAX) doesn t output. Check soldering. N.G. Correction of soldering. ・ C868 R868 R866 211 R862 R864 R863 Check the POWER UNIT. ・ R869 FB861 O. . N.G. Check the output signal. Replace the MAIN UNIT. ・ FB861 Check the digital signal for 3Vpp. O. . Replace C868 R868 R866 211 R862 R864 R863 R869 . 3. . Ether is not connection. N.G.
Page 35 MEASURING MET OD AND WAVEFORMS 1. VIDEO section To check the waveforms(VIDEO) on the MAIN UNIT, the ND (-) probe to " t CE30" point. Measuring Disc: VIDEO BLX-104 (Blu-ray disc) Playback Content : Title 1 , chapter 1 Color Bar 100 (Main Menu 9.94 1080i 1.Video signal 1.Color Bar 100 ) Component output resolution : 1080i (It is better to use wires for e tending between the probe and test points.) Since there are no test points for locations q to r , confirm the signals at the land of a chip resistor. MAIN UNIT TEST POINT AND WAVEFORMS Det i A t ND q U18 (N M2 66) Video out signal Component side qVideo out signal...
Page 36 Ter in output chec Signal: Color Bar 100 DBP-1611 Oscilloscope 7 ohm Load Video out terminal check Video out signal Component out terminal check Component out Y signal Component out Cb signal Component out Cr signal...
Page 37 BLOC DIAGRAM BD Core B oc F E B E Video B oc MAIN PWB MPE DECORDER BD / DVD / CD MT8 30 VIDEO OUT DRIVE UNIT VIDEO DRIVER FE CONT N M2 66AV BD DVD CD COMPONENT OUT Mecha RF Signal AACS CPPM CPRM Pick up...
Page 38 WIRING DIAGRAM DISPLAY UNIT STANDBY-SW UNIT BtoB F-9332H SUB POWER DRIVE MECHA UNIT UNIT PH-PH P1.0 9P FFC 47P FFC 5P PH BtoB BtoB P1.0 P0.5 HA700 J700 HA600 MAIN UNIT P1.0 POWER UNIT PH-PH J306 P1.0 REMOTE UNIT AC INLET...
Page 39 PRINTED WIRING BOARDS MAIN (COMPONENT SIDE) MAIN (FOIL SIDE) 鉛フリー半田半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Le d free So der When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 40 DISPLAY (COMPONENT SIDE) POWER (COMPONENT SIDE) 鉛フリー半田半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Le d free So der When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 41 DISPLAY (FOIL SIDE) POWER (FOIL SIDE) 鉛フリー半田半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Le d free So der When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 42 REMOTE (COMPONENT SIDE) REMOTE (FOIL SIDE) STANDBY-SW (COMPONENT SIDE) STANDBY-SW (FOIL SIDE) SUB POWE (COMPONENT SIDE) SUB POWE (FOIL SIDE) 鉛フリー半田半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Le d free So der When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 43 12k/1% 12k/1% 560/1% 560/1% 1.5k 1.5k 20PIN/FFC/1.0mm 20PIN/FFC/1.0mm LED_A 3.3k/1% 3.3k/1% LED_A LED_B LED_B 0.1uF/50V 0.1uF/50V W_REMOTE U3 TL431 U3 TL431 W_REMOTE FMEN-210A FMEN-210A 1.5k 1.5k PC817 PC817 TH1 2D22 TH1 2D22 3uH/5A 3uH/5A L2 3uH/2A L2 3uH/2A +12V MOTOR+12V 0.5A(Peak 2A) 5.5V_STBY 5V_STB...
Page 44 DBP-2011 only DBP-1611:0ohm 1SS355 9110S-09L NJM7809DL1A +12V +12V FBJ1608HS280NT FBJ1608HS280NT +12V 1SS355 MP2208 91K 1% AGND -12V 1000P EN/SYNC 0.01u 100K 0.01u MP2208 PGND1 PGND2 0.1u 47/16 3.3uH 1SS355 FBJ1608HS280NT 47/16 FBJ1608HS280NT 22/16 100K 0.47[B] 0.1u[Z] DBP-1611:0ohm DBP-2012 only 1SS355 NJM79M09DL1A 9110S-14L FBJ1608HS280NT...
Page 45 MR-6625UYB MR-6625UYB STBY_KEY V+VFD KEY_IN_B VCC_3.3V V+VFD 300R 300R 430R 430R 4.7k 4.3k 4.3k GR12 GR11 V-VFD GR10 -32V 100R 100R VFD_DATA 100k 100k 100R 100R VFD_CLK 1 Q5 KTA1504S KTA1504S KTA1504S KTA1504S 100R 100R VFD_STB SG20 SG20 KEY_IN_A 4.7k 4.7k 100k 100k...
Page 46 0.01 0.01 +5V_NSW_232C OPEN OPEN KRA104S KRA104S KDS160 KDS160 220pF 220pF 3.3K 3.3K OPEN OPEN W_REMOTE KTC3875S KTC3875S 220pF 220pF MINI-JACK MINI-JACK RB521S RB521S 20482E0004 20482E0004 C6 0.1Z C6 0.1Z OPEN OPEN DBP-2012X ONLY KTA1268 KTA1268 TP10 TP10 AMX_POWER DTC144E DTC144E BLM21PG221 BLM21PG221...
Page 47 A_KEY_IN R371 R371 BLM15P BLM15P FB27 FB27 KEY_IN_A PWR_AC_DET W_REMOTE W_REMOTE [13] B_KEY_IN R363 R363 BLM15P BLM15P FB25 FB25 KEY_IN_B PS_ON C1032 C1032 STB_KEY IR_IN IR_IN [13] B_KEY_IN C1034 C1034 KEY_IN_B KEY_IN_B [13] KEY_IN_A 3.3V KEY_IN_A [13] VFD_DATA 100pF/NC 100pF/NC 100pF/NC 100pF/NC VFD_CLK...
Page 48 1.8V U101 U101 U102 U102 U100A U100A A_DQ13 A_RA0 A_DQ16 A_RA0 A_DQ9 A_RA1 A_DQ22 A_RA1 1.8V C101 C101 C102 C102 C103 C103 C104 C104 C105 C105 C106 C106 C107 C107 A_DQ8 A_RA2 A_DQ21 A_RA2 0.1uF/16V 0.1uF/16V A_DQ11 A_RA3 A_DQ19 A_RA3 0.1uF/16V 0.1uF/16V 0.1uF/16V...
Page 49 U100B U100B U201 U201 U202 U202 B_DQ0 B_RA0 B_DQ18 B_RA0 B_DQ0 B_DQ4 B_RA1 B_DQ20 B_RA1 AR39 DVSS B_DQ0 B_DQ1 B_DQ2 B_RA2 B_DQ23 B_RA2 AW43 DVSS B_DQ1 B_DQ2 B_DQ1 B_RA3 B_DQ19 B_RA3 AU43 DVSS B_DQ2 1.8V B_DQ3 B_DQ6 B_RA4 B_DQ17 B_RA4 AU41 DVSS B_DQ3...
Page 50 FB200 FB200 1.2V BLM15P BLM15P U100C U100C 1.2V AVDD12_APLL FB206 FB206 HW TRAPPING AVDD12_HDMI C951 C951 BLM15P BLM15P NFREN NFREN [5,6] C927 C927 C953 C953 BE 1.2V:Below 0.1A NFWEN C952 C952 NFWEN [5,6] 0.1uF 0.1uF 0.1uF 0.1uF 10uF/10V 10uF/10V NFALE NFALE [5,6] 3.3V_VDAC...
Page 51 HW TRAPPING NAND U100E U100E 3.3V NFREN NFREN NFWEN FLASH NFWEN TP304 TP304 1.2V NFALE NFALE SFCS AVDD12_STX1 FB308 FB308 BLM15P BLM15P NFCLE 0402 NFCLE SFCS AVDD12_STX1 SFCK AVDD12_SRX1 FB301 FB301 BLM15P BLM15P U300 U300 SFCK AVDD12_SRX1 SFDI BE 1.2V:Below 0.1A NFCEN NFCEN SFDI...
Page 52 U100D U100D VCC3IO_STB 3.3V HW Trapping FB400 FB400 VCC3IO_STB1 BLM15P BLM15P ETCOL VCC3IO_STB1 ETCOL [12] ETCOL ETCRS ETCRS [12] VCC3IO_STB ETCOL C403 C403 C404 C404 ETCRS Close to 0402 (Test Mode) VCC3IO_STB ETCRS 3.3V_STBY VCC3IO_STB:Below 20mA 0.1uF 0.1uF ETMDC ETMDC ETMDC ETMDC [12]...
Page 53 U100F U100F 1.1V 1.1V VOUTVSYNC VCCK VOUTVSYNC V500 V500 VOUTHSYNC 3.3V AB20 VCCK VOUTHSYNC V501 V501 C537 C537 C538 C538 C523 C523 C526 C526 AD20 VCCK 10uF 10uF 0.1uF 0.1uF 4.7uF 4.7uF 4.7uF 4.7uF VOUTCLK1 EFVDDQ_CTL TP732 TP732 AF20 VCCK VOUTCLK1 V502 V502...
Page 54 M3.3V GIO14 /TRST FB604 FB604 AVCC BEFE_EX AVCC A1.2V GIO19 BLM18P BLM18P M3.3V GIO16 FE_RXIN FE_RXIN D3.3V GIO17 R648 R648 FE_RXIP FE_RXIP RTCK A3.3V C996 C996 GIO18 R649 R649 0.1uF 0.1uF C713 C713 C714 C714 GIO15 R652 R652 TGIO15 TGIO15 C691 C691 C690...
Page 55 MOTOR DRIVER GAINSW2 GAINSW2 [8] MOTOR MUTE2 MUTE2 V14REF R700 R700 R702 R702 MUTE1 MUTE1 R701 R701 R704 R704 MOTOR DRIVER V14REF R703 R703 R705 R705 TRAYPWM DRIVER TRAYPWM FB701 FB701 U700 U700 R706 R706 DMSO V14REF V14REF DMSO POWER BLM21P BLM21P DMSO...
Page 56 MIX 2CH L/R AUDIO CNT AMUTE AMUTE [4,6] U702 U702 NJM78L05uA NJM78L05uA AUDIO I2S AOMCLK AOMCLK MIX_+5V_DAC AOLRCK AOLRCK AOBCK 1SS301 1SS301 AOBCK AOSDATA0 CE20 CE20 AOSDATA0 DTA114EUA DTA114EUA 100uF/50v 100uF/50v 0.1uF 0.1uF +12VA SOT-89 SOT-89 MIX_OP+12V MIX_+5V_DAC AOSDATA4 AOSDATA4 CE24 CE24 CB12...
Page 57 ASPDIF CONNECTOR J861 J861 R862 R862 FB861 FB861 RCA2X3 RCA2X3 R863 2.2K R863 2.2K 1.8K 1.8K ASPDIF Q211 Q211 2N3904 2N3904 C868 C868 R868 68 R868 68 BLM15A BLM15A COAXOUT ML_OUT ML_OUT [10] C877 C877 C878 C878 MR_OUT R864 R864 R866 R866 R869...
Page 58 LAN-3.3V LAN_VDDA LAN-3.3V FB903 FB903 LAN_VDDA ETMDC ETMDC ETMDIO ETMDIO R931 10 R931 10 FB/0603 FB/0603 ETTXCLK ETTXCLK C975 C975 C976 C976 C977 C977 C978 C978 C979 C979 ETTXD0 ETTXD0 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF 10uF 0.1uF/16V 0.1uF/16V ETTXD1 ETTXD1 C980...
Page 59 MCU_2.5V C178 C178 R320 R320 MCU_SET1 100pF/NC 100pF/NC P0.5/ADC2 KEY_IN_B KEY_IN_B R323 R323 MCU_SET2 P0.4 MCU_IO_10 MCU_IR_IN MCU_3.3V Default for DENON R298 R298 MCU_SET3 MCU_IO_5 MCU_IO_14 MCU_IO_5 MCU_LED_CTRL_A [1] P0.3/ADB2 KEY_IN_A R356 R356 MCU_SET4 KEY_IN_A KEY_IN_B KEY_IN_B MCU_IO_15 KEY_IN_A MCU_LED_CTRL_B [1]...
Page 60 EXPLODED VIEW f WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要な部品です。従って交換時は必ず指定の部品を使用してください。...
Page 61 PARTS LIST OF EXPLODED VIEW dfgh zParts indicated by "nsp" on this table cannot be supplied. zP.W.B. ASS'Y indicated by "nsp" on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts list and order replacement parts. zParts indicated by the "...
Page 62 BLIND SHEET (1611) 4050213365000S LENS (POWER) 3710211123000S POWER KNOB BASE 5090214621000S KNOB CAP (1611BK) 4500210511000S KNOB CAP (1611SP) 4500210511100S DENON BADGE 5630210028300S DENON BADGE 5630210028400S KNOB 3P (1611BK) 5097214601000S KNOB 3P (1611SP) 5097214601100S FUNCTION KNOB (1611BK) 5090214581000S FUNCTION KNOB (1611SP)
Page 63 Ref.No. Part No. Part Name Remarks Q'ty WIRES 12P FFC ★ 60 00MYU12090540 (for BD MAIN PWB and REMOTE PWB connection) ★ 61 00MYU15080520 15P FFC N711150833810S ★ 62 5P CON. L002261050050S ★ 63 13P CON. L002201130050S ★ 64 00MYU20100520 20P FFC N711201033810S PARTS LIST OF P.W.B.
Page 64 PACKING VIEW dfh 1 3 4 5 6 11 121314...
Page 65 PARTS LIST OF PACKING VIEW dfgh zParts indicated by "nsp" on this table cannot be supplied. zParts indicated by the " ★ " mark are not illustrated in the exploded view. zThe parts listed below are only for maintenance, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Page 66 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC s P FP44 M in UNIT U1 VDD25 P1.2 SDA SWC P1.3 SCL SWC1 RSTN P1.4 SWC2 P2.4 T2EX CMPD P1.5 SWC3 P2.5 T2 CMPC T1 SWB1 PINT . CMPB PINT .1 P FP 44 CMPA SWA P4.2 SWB3 CEX2 SWA1 CMPA...
Page 67 I O Port De nition Assi n ent Function Function Description igh(3.3V) 0 igh(3.3V) 0 AC DET Detection signal is for AC power. or 60 pulse or 60 pulse Muting signal is for component video(YUV) output. igh is COMP MUTE igh(3.3V) i- (0V) for component video output is enabled. And low disable the component video output. RXD 0 igh(3.3V) igh(3.3V) Not use TXD 0 igh(3.3V) igh(3.3V) Not use EY IN B igh(3.3V)
Page 68 PT 3 2 Disp UNIT U5 Ter in Function Pin N Description Pin No. to S 3 1 31 Segment driver output pin S 4 to S 1 64 61 y l a l l l l i Reset input pin RSTB When this pin is set to "LOW", all functions are initiali ed. Chip select input pin CSB When this pin is set to " igh" Level, the serial data transfer is disabled.
Page 69 MT 53 M in UNIT U1 B oc Di DMI, CVBS, Component Motor USB 2.0 Driver MT8 30 Ethernet Audio DAC FLAS DRAM...
Page 70 PCM1 1 M in Unit U TOP VIEW EROA DEMP0 DEMP1 MUTE A ND DATA TEST Ter in Function TERMINAL DESCRIPTION NAME A ND round Audio data bit clock input DATA Audio data digital input (1) (2) DEMP0 De-emphasis control (1) (2) DEMP1 De-emphasis control...
Page 71 SMSC M in UNIT U B oc Di...
Page 72 N M25 AV M in UNIT U1 B oc Di...
Page 73 2. FL DISPLAY FL TUBE 15 BT 114GN Disp UNIT U3...
Page 74 Personal notes:...

Denon DBP-1611UD Service Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Denon DBP-1611UD

Summary of Contents for Denon DBP-1611UD

Page 2: Safety Precautions

Table of Contents