Page 1
Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E2R EUT DBP-2012UDCI DBP-2012UD UNIVERSAL AUDIO/VIDEO PLAYER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
WARNING AND LASER SAFETY INSTRUCTIONS WARNING WAARSCHUWING Alle IC’s en vele andere halfgeleiders zijn gevoelig All ICs and many other semi-conductors are voor elektrostatische ontladingen (ESD). susceptible to electrostatic discharges (ESD). Onzorgvuldig behandelen tijdens reparatie kan de Careless handling during repair can reduce life levensduur drastisch doen verminderen.
INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
Refer to "MEASURING METHOD AND WAVEFORMS". When you repair the BD MECHA UNIT, you can use the following JIG. Please order it from Denon Offi cial Service Distributor in your region if necessary. Do not supply it : 2-Dimensional Bar Code Reader (DS6708 made by Symbol Co. etc.) : 1 Set Do not supply it : 232C (TTL) –...
Page 8
DISASSEMBLY • Disassemble in order of the arrow in the following fi gure. • In the case of the re-assembling, assemble it in order of the reverse of the following fl ow. • In the case of the re-assembling, observe "attention of assembling". •...
1. FRONT PANEL ASSY → FRONT PANEL ASSY Proceeding : TOP COVER (1) Detach the LOADER PANEL. Shooting direction: B (2) Disconnect the connector wire and FFC cable. FFC cable (3) Lift up to unhook the claw and move in the direction of arrow to gradually pull out the assembly. Shooting direction: C Shooting direction: D View from the bottom...
Page 10
2. BD MAIN UNIT ASSY → → Proceeding : TOP COVER REAR PANEL ASSY BD MAIN UNIT (1) Detach the LOADER PANEL. Shooting direction: B (2) Disconnect the connector wires and FFC cables. FFC cable FFC cable FFC cable BD MAIN UNIT FFC cable BACK PANEL ASSY (3) Remove the screws.
Page 11
(5) Remove the screws, then remove the BD MAIN UNIT. BD MAIN UNIT BACK PANEL ASSY Please refer to "EXPLODED VIEW" for the disassembly method of MAIN P.W.B included in BD MAIN UNIT 3. DC FAN Proceeding : TOP COVER DC FAN →...
REMOVING DISCS (1) Remove the Top Cover. (2) Open the CD tray by turning the Drive gear counterclockwise. Drive gear Shooting direction: D...
Page 13
DIAGNOSTICS OF OPTICAL PICKUP d Laser drive current initial value: T 2 1 : m m m m : n n n n T 2 2 : m m m m : n n n n T 2 3 : m m m m : n n n n...
1. Iop checked Method Select the laser ON/OFF(CD/DVD/BD)mode of the test mode, and check the Iop value of CD laser, DVD laser or BD laser. (Refer to "6. Test mode") FL Display (The display part of 13 digits) L a s e r O n O f f Laser current check Press the 8 or 9...
Page 15
HOW TO REPLACE THE BD MAIN UNIT OR BD MECHA UNIT ASSY NOTE: The light pick-up laser diode (LD) is instantly degraded or damaged by static electricity or a power surge. When handling the BD MECHA UNIT, always be sure to earth yourself, and use an earth mat on the workbench and fl...
Page 16
[Connection] (1) Connect the PC and bar code reader. (2) Connect the 232C (TTL) side 4P PH connector of the USB - 232C (TTL) conversion jig to the MAIN PWB UNIT (CN601) of the set. (3) Connect the USB side of the USB - 232C (TTL) conversion jig to the PC. USB - 232C(TTL) conversion jig MAIN PWB UNIT 4P RE-PH CONN CORD (1000mm)
Page 17
(5) On the screen below, select "ComPort XX". Select the USB - 232C (TTL) conversion jig port. (6) Check "Directory".
Page 18
Click the left edge of the "Bar Code" window, and the cursor begins to fl ash. Click (8) Place the bar code reader over the bar code attached to the replacement BD MECHA UNIT ASSY. When the reader has fi nished reading the barcode, the read data is displayed. b If the 2-dimensional barcode data has already been read by the 2-dimensional barcode reader, and the converted data obtained, copy the data from the data file, and paste it into this section.
Page 19
(9) Click Write(F2). (10) When “Pass” changes to green, writing to the Flash ROM of the MAIN PWB UNIT is complete. (11) Switch off the set unit power, and remove the 232C (TTL) side 4P PH connector of the USB - 232C (TTL) conversion jig from the MAIN PWB UNIT (CN601).
2.4. Replace the BD MECHA UNIT ASSY (1) Remove the old BD MAIN UNIT from the set unit (see "DISASSEMBLY"). (2) Remove the MECHA COVER. MECHA COVER (3) Cut wire clamp band, then disconnect the connector wire and FFC cable. MAIN PWB UNIT FFC cable HA700...
Page 21
(5) Attach the BD MECHA UNIT ASSY for replacement to the set unit. (When assembling the unit, perform the steps in reverse order.) (6) Check that the 45P-FFC, 9P-FFC and 5P-PH connector cords have been connected. 2.4. Confi gure the settings of the set that contains the new BD MECHA UNIT (1) Check the laser amperage (see laser on/off mode in the test mode (page 25)).
SERVICE MODE 1. Initial setting mode 1.1. preparation (1) Equipment used: None (2) Unit setting: No spec other than the following procedure. 1.2. procedure b Initialize the BD player when com, peripheral parts of com, or MAIN P.W.B. unit has been replaced in servicing. b All user setting will be lost and its factory setting will be restored when this initialization is made.
Page 23
3. Tray lock mode g 3.1. preparation (1) Equipment used: None (2) Unit setting: No spec other than the following procedure. 3.2. procedure [Setting] (1) Pressing the 1 and 8 buttons for simultaneously, plug the AC cord into a power outlet. (2) "TRAY LOCK"...
6. Test mode f 6.1. Entering the test mode The test mode is entered by pressing the 5 and 3 buttons simultaneously, plug the AC cord into a power outlet. When the test mode is set, the " 1 " and " 3 " indicators light. FL tube display when test mode entered FL Display (The display part of 13 digits) When the test mode is set, the choice screen of the mode appears on the monitor.
Page 25
6.3. About each mode ・ With the mode selected, press the 1 button to set that mode. (1) Laser on/off (CD/DVD/BD) mode Press the 8 or 9 button to select [X] and press the 1 button to set it. Laser on/off control is executed and the laser current is displayed. FL Display (The display part of 13 digits) (X=1 : CD laser mode, 2 : DVD laser mode, 3 : BD(SL) laser mode) (mmmm[mA] : Stored data, nnnn[mA] : Current value)
Page 26
(3) Accumulated laser on time display mode Press the 8 or 9 button to select [Y] and press the 1 button to set it. The accumulated laser on time is displayed. FL Display (The display part of 13 digits) (Y=1 : CD, 2 : DVD , 3 : BD, mmmmmm : Time(Fractions of hours are counted up one hour on the display.) When the 2 button is pressed, the layer above the current layer is displayed.
Page 27
6.4. Stopping the mode When the 2 button is pressed, the layer above the current layer is displayed. The relationship between the different modes and the display of the different layers is shown on the table below. Mode 1 layer 2 layer 3 layer Laser on/off (CD/DVD/BD) mode...
Error rate display details for each media type Measurement Remarks position The inner It is invalid. It is invalid. It is invalid. When this is selected for BD, DVD or circumference of CD, T84 FFFFFFFFFF display. 2-layer The inner LDC error detection PI error detection It is invalid.
PROCEDURE FIRMWARE FOR UPGRADING THE VERSION OF THE FIRMWARE You can update by downloading the latest version from the Internet. 1. Update from the Internet 1.1. preparation (1) System requirements • Internet Connection by Broadband Circuit • Modem • Router •...
TROUBLE SHOOTING 1. POWER UNIT The power cannot be turned on. Defect of primary circuit component. ・[D101] (RBV1506) ・[U102] (STR-W6753) Check FUSE condition. ・[U103] (STR-A6059H) ・FUSE [F101] ・[T101] (AEP-ERL28075 (SW_TRANS)) ・[T102] (AEP-EE16202 (SW_TRANS)) and other circuits. Check parts and soldering. ・[U103] (STR-A6059H) Check 5.5V_STBY output.
2. DISPLAY UNIT 2.1. FL TUBE doesn't light. Check parts (surrounding) and soldering. ・[U3] (MR-6625UYB) ・[J1] (20x1/W/HOUSING) Check ±F output.(4.8V) POWER UNIT (J1 #14 - #16) ・[T101] (AEP-ERL28075 (SW_TRANS)) ※ 4.32V 〜 5.28V ・[D115] (FS34) ・[N101] (20P-FMN) and other circuits. Check parts (surrounding) and soldering.
Page 32
3. MAIN UNIT 3.1 Video out doesn't output. ・Check soldering (U702, U20). Check power supply. ・ C heck the power supply voltage of ・Check the power supply (+5V_AV) of U20. U702(1pin(+12VA)). Check input signal to [U20]. ・ C heck soldering (U20, U100, U20(1pin and 6pin) ・Is data input to 6pin? and surrounding circuitry).
Page 33
3.2. Component out doesn't output. Check power supply. ・ C heck the power supply (1.0V_ABT, 1.8V_ABT, +3.3V_V) of U22. ・ C heck soldering (U7, U13, U17, U702 and ・ C heck the power supply (+3.3V_DDST) of U225. surrounding circuitry).
Page 34
3.3. HDMI out doesn't output. Check power supply. ・ C heck the power supply (1.0V_ABT, 1.8V_ABT, +3.3V_V) of U22. ・ C heck soldering (U7, U13, U17, U702 and ・ C heck the power supply (+3.3V_DDST) of U225. surrounding circuitry).
Page 35
3.4 Digital Out(COAX) doesn't output. Check soldering. Repair soldering. ・[C868][R868][R866][Q212][R862][R864][R863] Check the POWER UNIT. ・[R869][FB861] Check output signal. Replace the MAIN UNIT. ・[FB861] Check the digital signal for 3Vpp. Replace [C868][R868][R866][Q211][R862][R864] [R863][R869]. 3.5. Ether is not connection. Check the input signal of [U901]SMSC8710. Replace the MAIN UNIT.
4. AUDIO UNIT 4.1 Audio doesn't output. ・Check soldering (U9-12 surrounding). Check Power supply and connection to POWER ・ C heck N1 : 5P PH, 1pin (+12V), 3pin(-12V). input UNIT. ・ C heck the local power source, U11 (+9V), from POWER UNIT. ・Check cable insertion.
MEASURING METHOD AND WAVEFORMS To check the waveforms on the Main P.W.B., the GND (-) probe of the oscilloscope to t “CE30” point. Measuring Disc: BLX-104 (Blu-ray disc) Playback Content: Title 1 , chapter 1 Color Bar 100% (Main Menu 59.94Hz 1080i 1.Video signal 1.Color Bar 100%) Component output resolution:...
Page 38
q U20 (NJM2566)_Video out_signal (C32) Video out_signal w - r U20 (NJM2566)_Component out_Y/Cb/Cr signal (Y:C29, Cb:C30, Cr:C31) Component out_Y signal Component out_Cb signal Component out_Cr signal...
Page 39
Terminal output check DBP-2012 Oscilloscope 75ohm Load Video Out terminal check Video out_signal Component Out terminal check Component out_Y signal Component out_Cb signal Component out_Cr signal...
Page 50
RS-232C K202 OPEN S201 OPEN R211 R215 C228 OPEN C218 D201 RB521S 1000P D202 C229 OPEN C219 1SS355 C204 0.1Z 1000P 1608 R212 C205 0.1Z 1608 R218 R217 1SS355 D203 OPEN OPEN C206 R216 R220 R219 D204 OPEN OPEN C220 D205 R201 OPEN...
Page 51
14P-TUCP-SOCKET 9P-TUCP-SOCKET 1608 1608 1608 1608 0.47 0.47 1.8K OPEN OPEN 1.8K 499K 499K UDZS4.7B UDZS4.7B OPEN OPEN 4.7u 4.7u 4.7u 4.7u 0.01 0.01 OPEN OPEN 0.1Z 0.1Z 1000P 1000P OPEN OPEN OPEN. SMD(6.6) OPEN. SMD(6.6) 2125 BLM18PG330SN1D OPEN 2125 OPEN...
Page 52
HDMI RESOLUTION PURE DIRECT (Denon)DISC LAYER OPEN PLAY LED_A1 LED_B1 PAUSE STOP PREV NEXT (Denon)SOURCE OSCI SG35 SG35 OSCO SG34 SG34 RSTB SG33 SG33 VFD_STB SG32 SG32 VFD_CLK CLKB SG31 SG31 VFD_DATA SG30 SG30 SG29 SG29 SG28 SG28 SG27 SG27...
Page 53
100/16 100/16 1SS355 1SS355 OPEN OPEN OPEN OPEN OPEN. DGND 100/50 0.01 +5VA OPEN 100/25 +3.3VD 100/25 2200/16 OPEN. CE(6.8) (TE85L) 100K 1SS301 6800P 6800P 6.8V 0.018 0.018 2.2K UDZS6.8B 2200P 2200P +5VA +5VA DTC114EK DTC114EK 100K 100K TPF3 OPEN OPEN...
PARTS LIST OF EXPLODED VIEW zParts indicated by "nsp" on this table cannot be supplied. zP.W.B. ASS'Y indicated by "nsp" on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts list and order replacement parts. zParts indicated by the "...
Page 78
BLIND SHEET (1611) 4050213365000S LENS (POWER) 3710211123000S POWER KNOB BASE 5090214621000S KNOB CAP (1611BK) 4500210511000S KNOB CAP (1611SP) 4500210511100S DENON BADGE 5630210028300S DENON BADGE 5630210028400S KNOB 3P (1611BK) 5097214601000S KNOB 3P (1611SP) 5097214601100S FUNCTION KNOB (1611BK) 5090214581000S FUNCTION KNOB (1611SP)
PARTS LIST OF PACKING VIEW zParts indicated by "nsp" on this table cannot be supplied. zParts indicated by the " ★ " mark are not illustrated in the exploded view. zThe parts listed below are only for maintenance, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Low(0V) High(3.3V) 10k PU High is for HDMI work normal.And low is for HDMI off. High(3.3V) High(3.3V) MCU setting pin by externail resistance.1 is for DENON P3.5 MCU_SET1 10k PU or Low(0V) or Low(0V) and 0 is for MARANZ High(3.3V) High(3.3V)
I/O Port Defi nition Port Assignment Function PU/PD Function Description Name Normal I2C Data signal that comunicate with MT8530. P1.2 MCU_IIC_SDA High(3.3V) Hi-Z 4.7K PU SW3.3V (Slave mode). High(3.3V)/50Hz High(3.3V)/50Hz P1.1 AC_DET 10k PU Detection signal is for AC power. or 60Hz pulse or 60Hz pulse P1.0 Not use...
Page 84
PT6302 (DISPLAY UNIT : U5) Terminal Function Pin Name Description Pin No. SG5 to SG35 1 ~ 31 Segment driver output pin SG4 to SG1 64 ~ 61 l l i l l i Reset input pin RSTB When this pin is set to "LOW", all functions are initialized. Chip select input pin When this pin is set to "High"...
Page 85
MT8530 (MAIN UNIT : U100) Block Diagram HDMI, CVBS, Component Motor USB 2.0 Driver MT8530 Ethernet Audio DAC FLASH DRAM...
Page 86
LAN8710 (MAIN UNIT : U901) Block Diagram...
Page 87
NJM2566AV (MAIN UNIT : U20) Block Diagram...
Page 88
PCM1795DBR (AUDIO UNIT : U1, U101, U111, U201, U211) ZEROL ZEROR AGND3L MSEL LRCK DATA AGND2 DGND AGND1 AGND3R Block Diagram I OUT L LRCK Current V OUT L Segment DATA Audio I OUT L+ Data Input I/V and Filter V COM L Oversampling Advanced...
Page 89
Terminal Function TERMINAL DESCRIPTIONS DESCRIPTIONS NAME AGND1 Analog ground (internal bias) AGND2 Analog ground (internal bias) AGND3L Analog ground (L-channel DACFF) AGND3R Analog ground (R-channel DACFF) Bit clock input (1) Serial audio data input (1) DATA DGND Digital ground I OUT L+ L-channel analog current output+ I OUT L–...
Page 90
HIN202EIBNZ-T (IR POWER UNIT : U201) 0.1μF +5V TO 10V 0.1μF VOLTAGE INVERTER +10V TO -10V 0.1μF VOLTAGE INVERTER 0.1μF 400kΩ 400kΩ 5kΩ 5kΩ...