Supero SUPERSERVER 6016T-URF User Manual
  1. Manuals
  2. Brands
  3. Supero Manuals
  4. Server
  5. SUPERSERVER 6016T-URF
  6. User manual

Supero SUPERSERVER 6016T-URF User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S
UPER
S
S
UPER
S
S
UPER
S
S
UPER
S
S
UPER
USER'S MANUAL
6016T-URF
ERVER
6016T-UF
ERVER
6016T-NTRF
ERVER
6016T-NTF
ERVER
1.0b
®

Advertisement

Table of Contents
loading

Related Manuals for Supero SUPERSERVER 6016T-URF

Summary of Contents for Supero SUPERSERVER 6016T-URF

  • Page 1 UPER ® 6016T-URF UPER ERVER 6016T-UF UPER ERVER 6016T-NTRF UPER ERVER 6016T-NTF UPER ERVER USER’S MANUAL 1.0b...
  • Page 2 The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.

  • Page 3: About This Manual

    Preface About This Manual This manual is written for professional system integrators and PC technicians. It pro- vides information for the installation and use of the SuperServer 6016T-URF/6016T- UF/6016T-NTRF/6016T-NTF. Installation and maintenance should be performed by experienced technicians only. Manual Organization Chapter 1: Introduction The fi...
  • Page 4 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Chapter 5: Advanced Serverboard Setup Chapter 5 provides detailed information on the X8DTU-F serverboard, including the locations and functions of connections, headers and jumpers. Refer to this chapter when adding or removing processors or main memory and when reconfi guring the serverboard.
  • Page 5 Preface Notes...

  • Page 6: Table Of Contents

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Table of Contents Chapter 1 Introduction Overview ......................1-1 Serverboard Features ..................1-2 Processors ...................... 1-2 Memory ......................1-2 UIO ........................1-2 Serial ATA ....................... 1-2 Onboard Controllers/Ports ................1-2 Graphics Controller ..................1-3 Other Features ....................1-3 Server Chassis Features ................
  • Page 7 Table of Contents Installing the Server into the Rack ..............2-6 Installing the Server into a Telco Rack ............2-7 Checking the Serverboard Setup ..............2-8 Checking the Drive Bay Setup ................ 2-9 Chapter 3 System Interface Overview ......................3-1 Control Panel Buttons ..................
  • Page 8 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Adding PCI Cards ..................5-10 Serverboard Details ..................5-11 X8DTU-F Quick Reference ................5-12 Connector Defi nitions ..................5-13 Jumper Settings .................... 5-19 5-10 Onboard Indicators ..................5-22 5-11 SATA Port Connections ................. 5-23 5-12 Installing Software ..................5-24 Super Doctor III .....................

  • Page 9: Chapter 1 Introduction

    Chapter 1: Introduction Chapter 1 Introduction Overview The SuperServer 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF is a high-end server comprised of two main subsystems: the SC815TQ-R650UBP (6016T- URF/6016T-NTRF)/SC815TQ-560UBP (6016T-UF/6016T-NTF) 1U server chassis and the X8DTU-F dual processor serverboard. Please refer to our web site for information on operating systems that have been certifi...

  • Page 10: Serverboard Features

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Serverboard Features At the heart of the SuperServer 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF lies the X8DTU-F, a dual processor serverboard based on the Intel® IOH-36D (North Bridge) + ICH10R (South Bridge) chipset. Below are the main features of the X8DTU-F. (See Figure 1-1 for a block diagram of the chipset).

  • Page 11: Graphics Controller

    Chapter 1: Introduction Graphics Controller The X8DTU-F features an integrated Matrox G200eW graphics chip, which includes 8 MB of DDR2 memory. Other Features Other onboard features that promote system health include onboard voltage moni- tors, auto-switching voltage regulators, chassis and CPU overheat sensors, virus protection and BIOS rescue.

  • Page 12: Front Control Panel

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual 6016T-NTRF/6016T-NTF: A riser card (RSC-R1UU-E8PR, optional) on the right side of the chassis can support AOC-PG-i2+ add-on card to provide two Gb LAN ports. The left side supports two PCI-E x8 cards. See section 5-6 for details. (Right and left refer to the side when viewed from the front of the system.

  • Page 13: System Block Diagram

    Chapter 1: Introduction Figure 1-1. Intel IOH-36D/ICH10R Chipset: System Block Diagram Note: This is a general block diagram. Please see Chapter 5 for details. CPU 1 CPU 2 Port 1 Port 0 Gen2 x4 Gen2 x16 Intel 82576 Ports 7,8,9,10 Ports 1,2 (Lane Reversal) Intel 5520...

  • Page 14: Contacting Supermicro

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V.

  • Page 15: Chapter 2 Server Installation

    Unpacking the System You should inspect the box the SuperServer 6016T-URF/6016T-UF/6016T- NTRF/6016T-NTF was shipped in and note if it was damaged in any way. If the server itself shows damage you should fi le a damage claim with the carrier who delivered it.

  • Page 16: Choosing A Setup Location

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Choosing a Setup Location • Leave enough clearance in front of the rack to enable you to open the front door completely (~25 inches) and approximately 30 inches of clearance in the back of the rack to allow for suffi cient airfl ow and ease in servicing.This product is for installation only in a Restricted Access Location (dedicated equipment rooms, service closets and the like).

  • Page 17: Rack Mounting Considerations

    Chapter 2: Server Installation • Allow the hot plug SATA drives and power supply modules to cool before touch- ing them. • Always keep the rack's front door and all panels and components on the servers closed when not servicing to maintain proper cooling. Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating tempera-...

  • Page 18: Installing The System Into A Rack

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Installing the System into a Rack This section provides information on installing the 6016T-URF/6016T-UF/6016T- NTRF/6016T-NTF into a rack unit with the rack rails provided. If the system has already been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6. There are a variety of rack units on the market, which may mean the assembly procedure will differ slightly.

  • Page 19: Installing The Outer Rails

    Chapter 2: Server Installation Installing the Outer Rails Begin by measuring the distance from the front rail to the rear rail of the rack. Attach a short bracket to the front side of the right outer rail and a long bracket to the rear side of the right outer rail.

  • Page 20: Installing The Server Into The Rack

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Installing the Server into the Rack You should now have rails attached to both the chassis and the rack unit. The next step is to install the server into the rack. Do this by lining up the rear of the chassis rails with the front of the rack rails.

  • Page 21: Installing The Server Into A Telco Rack

    Chapter 2: Server Installation Installing the Server into a Telco Rack To install the 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF into a Telco type rack, use two L-shaped brackets on either side of the chassis (four total). First, determine how far follow the server will extend out the front of the rack. Larger chassis should be positioned to balance the weight between front and back.

  • Page 22: Checking The Serverboard Setup

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Checking the Serverboard Setup After you install the 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF in the rack, you will need to open the top cover to make sure the serverboard is properly installed and all the connections have been made. Accessing the Inside of the System 1.

  • Page 23: Checking The Drive Bay Setup

    Chapter 2: Server Installation Figure 2-5. Accessing the Inside of the System Checking the Drive Bay Setup Next, you should check to make sure the peripheral drives and the SATA drives and SATA backplane have been properly installed and all connections have been made.
  • Page 24 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Checking the Airfl ow 1. Airfl ow is provided by four sets of 4-cm fans (each set of fans consists of two fans that are mounted back to back). The system component layout was carefully designed to direct suffi cient cooling airfl ow to the components that generate the most heat.

  • Page 25: Chapter 3 System Interface

    Chapter 3: System Interface Chapter 3 System Interface Overview There are several LEDs on the control panel as well as others on the SATA drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of specifi...

  • Page 26: Control Panel Leds

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Power The main power button is used to apply or remove power from the power supply to the server system. Turning off system power with this button removes the main power but keeps standby power supplied to the system. Control Panel LEDs The control panel located on the front of the SC815TS-R560U/SC815TS-560UBP chassis has fi...
  • Page 27 Indicates network activity on LAN2 when fl ashing. NIC1 Indicates network activity on LAN1 when fl ashing. On the SuperServer 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF, this light indicates SATA and/or DVD-ROM drive activity when fl ashing. Power Indicates power is being supplied to the system's power supply units. This LED...

  • Page 28: Hard Drive Carrier Leds

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Hard Drive Carrier LEDs Each hard drive carrier has two LEDs. • Green: When illuminated, the green LED on the front of the drive carrier in- dicates drive activity. A connection to the drive backplane enables this LED to blink on and off when that particular drive is being accessed.

  • Page 29: Chapter 4 Standardized Warning Statements For Ac Systems

    Chapter 4: Warning Statements for AC Systems Chapter 4 Standardized Warning Statements for AC Systems About Standardized Warning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance.
  • Page 30 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befi nden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut.
  • Page 31 Warning Statements for AC Systems ‫ﺟﺴﺪﻳﺔ‬ ‫ﺍﺻﺎﺑﺔ‬ ‫ﺗﺘﺴﺒﺐ ﻓﻲ‬ ‫ﺣﺎﻟﺔ ﻳﻤﻜﻦ ﺃﻥ‬ ‫ﺍﻧﻚ ﻓﻲ‬ ‫ﺧﻄﺮ‬ ‫ﻳﻌﻨﻲ‬ ‫ﻫﺬﺍ ﺍﻟﺮﻣﺰ‬ !‫ﺗﺤﺬﻳﺮ‬ ‫ﺍﻟﺪﻭﺍﺋﺮ‬ ‫ﺑﺎﻟﻤﺨﺎﻁﺮ ﺍﻟﻨﺎﺟﻤﺔ ﻋﻦ‬ ‫ﻦ ﻋﻠﻰ ﻋﻠﻢ‬ ، ‫ﻛ‬ ‫ﻣﻌﺪﺍﺕ‬ ‫ﺗﻌﻤﻞ ﻋﻠﻰ ﺃﻱ‬ ‫ﻗﺒﻞ ﺃﻥ‬ ‫ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ‬ ‫ﺣﻮﺍﺩﺙ‬ ‫ﺃﻱ‬ ‫ﻭﻗﻮﻉ‬ ‫ﻤﻨﻊ‬ ‫ﻟ‬ ‫ﺍﻟﻮﻗﺎﺋﻴﺔ‬...

  • Page 32: Installation Instructions

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Installation Instructions Warning! Read the installation instructions before connecting the system to the power source. 警告 将此系统连接电源前,请先阅读安装说明。 警告 將系統與電源連接前，請先閱讀安裝說明。 Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.

  • Page 33: Circuit Breaker

    Chapter 4: Warning Statements for AC Systems Circuit Breaker Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 20 A. 警告 此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电 流不大于250V,20A。 警告 此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電 流不大於250V,20A。...

  • Page 34: Power Disconnection Warning

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V, 20A. Power Disconnection Warning Warning! The system must be disconnected from all sources of power and the power cord removed from the power supply module(s) before accessing the chassis interior to install or remove system components.
  • Page 35 Chapter 4: Warning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché...

  • Page 36: Equipment Installation

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Equipment Installation Warning! Only trained and qualifi ed personnel should be allowed to install, replace, or service this equipment. 警告 只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。 警告 只有經過受訓且具資格人員才可安裝、更換與維修此設備。 Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifi ziertem Personal gestattet werden. ¡Advertencia! Solamente el personal califi...

  • Page 37: Restricted Area

    Chapter 4: Warning Statements for AC Systems Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door geschoold en gekwalifi ceerd personeel. Restricted Area Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

  • Page 38: Battery Handling

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual ‫אזור עם גישה מוגבלת‬ !‫אזהרה‬ ‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה. הגישה ניתנת בעזרת‬ .('‫כלי אבטחה בלבד )מפתח, מנעול וכד‬ ‫ﻣﺤﻈﻮﺭﺓ‬ ‫ﻣﻨﺎﻁﻖ‬ ‫ﻟﺘﺮﻛﻴﺒﻬﺎ ﻓﻲ‬ ‫ﻫﺬﻩ ﺍﻟﻮﺣﺪﺓ‬ ‫ﺗﺨﺼﻴﺺ‬ ‫ﺗﻢ‬ ،‫ﺃﺩﺍﺓ ﺧﺎﺻﺔ‬ ‫ﻣﻦ ﺧﻼﻝ ﺍﺳﺘﺨﺪﺍﻡ‬ ‫ﻓﻘﻂ‬...
  • Page 39 Chapter 4: Warning Statements for AC Systems Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant.

  • Page 40: Redundant Power Supplies

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Redundant Power Supplies Warning! This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. 警告 此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。 警告 此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。 Warnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

  • Page 41: Backplane Voltage

    Chapter 4: Warning Statements for AC Systems ‫ﺍﻣﺪﺍﺩ ﺍﻟﻄﺎﻗﺔ‬ ‫ﺑﻮﺣﺪﺍﺕ‬ ‫ﻋﺪﺓ ﺍﺗﺼﺎﻻﺕ‬ ‫ﺠﻬﺎﺯ‬ ‫ﺍﻟ‬ ‫ﻳﻜﻮﻥ ﻟﻬﺬﺍ‬ ‫ﻗﺪ‬ ‫ﺍﻟﻜﻬﺮﺑﺎء‬ ‫ﻋﻦ‬ ‫ﻮﺣﺪﺓ‬ ‫ﺍﻟ‬ ‫ﻟﻌﺰﻝ‬ ‫ﻛﺎﻓﺔ ﺍﻻﺗﺼﺎﻻﺕ‬ ‫ﻳﺠﺐ ﺇﺯﺍﻟﺔ‬ Waarschuwing Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken. Backplane Voltage Warning! Hazardous voltage or energy is present on the backplane when the system is...

  • Page 42: Comply With Local And National Electrical Codes

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual ‫מתח בפנל האחורי‬ !‫הרה‬ ‫אז‬ ‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת. יש להיזהר במהלך‬ .‫העבודה‬ ‫ﺍﻟﻠﻮﺣﺔ‬ ‫ﺃﻭﺍﻟﻄﺎﻗﺔ ﺍﻟﻤﻮﺟﻮﺩﺓ ﻋﻠﻰ‬ ‫ﺍﻟﺘﻴﺎﺭ ﺍﻟﻜﻬﺮﺑﺎﺋﻲ‬ ‫ﻣﻦ‬ ‫ﺧﻄﺮ‬ ‫ﻫﻨﺎﻙ‬ ‫ﻫﺬﺍ ﺍﻟﺠﻬﺎﺯ‬ ‫ﺧﺪﻣﺔ‬ ‫ﻛﻦ ﺣﺬﺭﺍ ﻋﻨﺪ‬ ‫ﻳﻌﻤﻞ‬ ‫ﺍﻟﻨﻈﺎﻡ‬ ‫ﻋﻨﺪﻣﺎ ﻳﻜﻮﻥ‬ Waarschuwing Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het systeem in gebruik is.

  • Page 43: Product Disposal

    Chapter 4: Warning Statements for AC Systems Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. ‫תיאום חוקי החשמל הארצי‬ !‫אזהרה‬ ‫הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬ ‫התקנת‬ ‫ﺍﻟﻤﺘﻌﻠﻘﺔ‬ ‫ﺍﻟﻤﺤﻠﻴﺔ ﻭﺍﻟﻮﻁﻨﻴﺔ‬ ‫ﻘﻮﺍﻧﻴﻦ‬ ‫ﻳﺠﺐ ﺃﻥ ﻳﻤﺘﺜﻞ ﻟﻠ‬ ‫ﺍﻟﻜﻬﺮﺑﺎﺋﻴﺔ‬...

  • Page 44: Hot Swap Fan Warning

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
  • Page 45 Chapter 4: Warning Statements for AC Systems 警告 當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Warnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador del chasis.

  • Page 46: Power Cable And Ac Adapter

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Power Cable and AC Adapter Warning! When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fi re. Electrical Appliance and Material Safety Law prohibits the use of UL or CSA -certifi...
  • Page 47 Chapter 4: Warning Statements for AC Systems Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné. L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit l'utilisation de UL ou CSA câbles certifi...
  • Page 48 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Notes 4-20...

  • Page 49: Chapter 5 Advanced Serverboard Setup

    Chapter 5: Advanced Serverboard Setup Chapter 5 Advanced Serverboard Setup This chapter covers the steps required to install processors and heatsinks to the X8DTU-F serverboard, connect the data and power cables and install add-on cards. All serverboard jumpers and connections are described and a layout and quick reference chart are included in this chapter.

  • Page 50: Processor And Heatsink Installation

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Processor and Heatsink Installation Caution: When handling the processor, avoid placing direct pressure on the label area of the fan. Also, do not place the serverboard on a conductive surface, which can damage the BIOS battery and prevent the system from booting up. Notes: •...
  • Page 51 Chapter 5: Advanced Serverboard Setup 1. After removing the plastic cap, use your thumb and the index fi nger to hold the CPU at the north and south center edges. 2. Align the CPU key (the semi-circle cutout) with the socket key (the notch below the gold color dot on the side of the socket).

  • Page 52: Installing The Heatsink

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Installing the Heatsink 1. Place the heatsink on top of the CPU so that the four mounting holes are aligned with those on the retention mechanism. Thermal Grease 2. Remove the thin layer of protective fi...

  • Page 53: Removing The Heatsink

    Chapter 5: Advanced Serverboard Setup Removing the Heatsink Warning: We do not recommend removing the CPU or the heatsink. If you do need to remove the heatsink, please follow the instructions below to prevent damage to the CPU or other components. 1.

  • Page 54: Connecting Cables

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Connecting Cables Now that the processors are installed, the next step is to connect the cables to the serverboard. These include the data (ribbon) cables for the peripherals and control panel and the power cables. Connecting Data Cables The cables used to transfer data from the peripheral devices have been carefully routed in preconfi...

  • Page 55: I/O Ports

    Chapter 5: Advanced Serverboard Setup See the Connector Defi nitions section in this chapter for details and pin descrip- tions of JF1. Figure 5-1. Front Control Panel Header Pins (JF1) Ground x (key) x (key) Power LED HDD LED UID Switch/Vcc NIC1 NIC2 OH/Fan Fail/UID LED...

  • Page 56: Installing Memory

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Installing Memory Note: Check the Supermicro web site for recommended memory modules. CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage. Installing DIMMs 1. Insert the desired number of DIMMs into the memory slots, starting with slot P1-DIMM1A.
  • Page 57 Chapter 5: Advanced Serverboard Setup memory allocation to system devices, memory remaining available for operational use will be reduced when 4 GB of RAM is used. The reduction in memory availability is disproportional. (Refer to the Memory Availability Table below for details.) Possible System Memory Allocation &...

  • Page 58: Adding Pci Cards

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Adding PCI Cards PCI Expansion Slots Riser cards are used to support add-on cards to the system. See the tables below for the expansion cards that may be used in the SC815TQ-R650U/SC815TQ-560U chassis. PCI Card Installation Before installing a PCI add-on card, make sure you install it into the correct riser card.

  • Page 59: Serverboard Details

    Chapter 5: Advanced Serverboard Setup Serverboard Details Figure 5-4. SUPER X8DTU-F Layout (not drawn to scale) Fan8 JPW2 (CPU2) P2-DIMM3A JPW3 P2-DIMM3B KB /MS JPW1 P2-DIMM2A P2-DIMM2B JPI2C P2-DIMM1A CPU1 P2-DIMM1B Fan1 Fan2 Battery X8DTU-F CPU2 Fan7 Speaker (CPU1) Fan3 LAN1 P1-DIMM1B P1-DIMM1A...

  • Page 60: X8Dtu-F Quick Reference

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual X8DTU-F Quick Reference Jumper Description Default Setting JBT1 CMOS Clear (See Section 5-9) C1/JI SMB to PCI-Exp. Slots Open (Disabled) ME Mode Select Open (Normal) ME Recovery Open (Normal) JPG1 VGA Enable/Disable Pins 1-2 (Enabled) JPL1 LAN1/2 Enable/Disable Pins 1-2 (Enabled)

  • Page 61: Connector Defi Nitions

    Chapter 5: Advanced Serverboard Setup Connector Defi nitions ATX Power 20-pin Connector Pin Defi nitions (JPW1) Pin# Defi nition Pin # Defi nition ATX Power Connector PS On Ground The primary ATX power supply con- 5VSB Ground nector meets the SSI EPS 12V speci- Ground Ground fi...
  • Page 62 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual HDD LED The HDD (IDE Hard Disk Drive) LED HDD LED Pin Defi nitions (JF1) connection is located on pins 13 and Pin# Defi nition 14 of JF1. Attach the IDE hard drive LED cable to display disk activity. HD Active Refer to the table on the right for pin defi...
  • Page 63 Chapter 5: Advanced Serverboard Setup Power Fail LED Power Fail LED Pin Defi nitions (JF1) The Power Fail LED connection is Pin# Defi nition located on pins 5 and 6 of JF1. Refer to the table on the right for pin defi ni- Ground tions.
  • Page 64 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Universal Serial Bus Headers Universal Serial Bus Headers Pin Defi nitions (USB2/3, USB4/5) Four additional USB headers (USB2/3 USB2, USB4 USB3, USB5 and USB4/5) are included on the Pin # Defi nition Pin # Defi nition serverboard.
  • Page 65 Chapter 5: Advanced Serverboard Setup Power LED/Speaker Speaker Connector Pin Defi nitions (JD1) On the JD1 header, pins 1-3 are for Pin # Function Defi nition a power LED and pins 4-7 are for an Speaker data (red wire) external speaker. See the table on the No connection right for speaker pin defi...
  • Page 66 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Power SMB (I C) Connector PWR SMB Pin Defi nitions (JPI The Power System Management Bus Pin# Defi nition C) header (JPI C) is used to moni- Clock tor the power supply, fan and system Data temperatures.

  • Page 67: Jumper Settings

    Chapter 5: Advanced Serverboard Setup Jumper Settings Explanation of Jumpers To modify the operation of the serverboard, jumpers can be used Connector to choose between optional settings. Pins Jumpers create shorts between two pins to change the function of the Jumper connector.
  • Page 68 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual LAN Enable/Disable LAN Enable/Disable Change the setting of jumper JPL1 to Jumper Settings (JPL1) enable or disable the onboard Ether- Jumper Setting Defi nition net (RJ45) ports LAN1 and LAN2. See Pins 1-2 Enabled the table on the right for jumper set- Pins 2-3 Disabled tings.
  • Page 69 Chapter 5: Advanced Serverboard Setup BMC/PHY Reset Jumper JPRST1 allow the user to reset BMC/PHY Jumper Settings (JPRST1) the Winbond WPCM450 BMC (Base- Jumper Setting Defi nition board Management Controller) chip Closed Reset BMC & PHY and the PHY chip. The default is set Open Normall to Open for normal operation.

  • Page 70: 5-10 Onboard Indicators

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual 5-10 Onboard Indicators LAN1/LAN2 LEDs The Ethernet ports (located beside the LAN LED VGA port) have two LEDs. On each Connection Speed Indicator LED Color Defi nition Gigabit LAN port, one LED indicates No connection or 10 Mb/s activity when blinking while the other LED may be green, amber or off to Green...

  • Page 71: 5-11 Sata Port Connections

    Chapter 5: Advanced Serverboard Setup The LE2 LED (located under SW1) is the UID indicator LED. LE2 illuminates when UID is initiated either by the UID button or via IPMI. If initiated a second time, LE2 will turn off. When the LED blinks blue it means the signal was initiated via IPMI.

  • Page 72: 5-12 Installing Software

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual 5-12 Installing Software After the hardware has been installed, you should fi rst install the operating system and then the drivers. The necessary drivers are all included on the Supermicro CDs that came packaged with your serverboard. Figure 5-5.

  • Page 73: Super Doctor Iii

    Chapter 5: Advanced Serverboard Setup Super Doctor III The Super Doctor III program is a Web base management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called SD III Client. The Super Doctor III program included on the CDROM that came with your serverboard allows you to monitor the environment and operations of your system.
  • Page 74 Figure 5-7. Super Doctor III Interface Display Screen (Remote Control) Note: SD III Software Revision 1.0 can be downloaded from our Web Site at: ftp:// ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's Guide at: http://www.supermicro.com/PRODUCT/Manuals/SDIII/UserGuide.pdf. For Linux, we will still recommend Supero Doctor II. 5-26...

  • Page 75: 5-13 Onboard Battery

    Chapter 5: Advanced Serverboard Setup 5-13 Onboard Battery Care must be taken to assure that the chassis cover is in place when the 6016T- URF/6016T-UF/6016T-NTRF/6016T-NTF is operating to assure proper cooling. Out of warranty damage to the system can occur if this practice is not strictly followed. Figure 5-8.
  • Page 76 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Notes 5-28...

  • Page 77: Chapter 6 Advanced Chassis Setup

    Chapter 6: Advanced Chassis Setup Chapter 6 Advanced Chassis Setup This chapter covers the steps required to install components and perform mainte- nance on the SC815TQ-R650U/SC815TQ-560U chassis. For component installa- tion, follow the steps in the order given to eliminate the most common problems encountered.

  • Page 78: Control Panel

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Figure 6-1. Chassis: Front and Rear Views Slim DVD-ROM Drive System LEDs Control Panel Hard Drive Bays System Reset Main Power Power Supply Modules USB Ports PCI Expansion Slots (w/ riser cards) Mouse/Keyboard COM1 Port VGA Port Ethernet Ports Note: the SC815TQ-560UBP chassis (6016T-UF/6016T-NTF) has only a single power supply...

  • Page 79: System Fans

    Chapter 6: Advanced Chassis Setup System Fans Four 4-cm heavy duty counter-rotating fans provide the cooling for the SuperServer 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF. Each fan unit is actually made up of two fans joined back-to-back, which rotate in opposite directions. This counter- rotating action generates exceptional airfl ow and works to dampen vibration levels. It is very important that the chassis top cover is properly installed and making a good seal in order for the cooling air to circulate properly through the chassis and cool the components.

  • Page 80: Drive Bay Installation/Removal

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Figure 6-2. System Cooling Fans Drive Bay Installation/Removal Removing the Front Bezel If your system has a front bezel (optional) attached to the chassis, you must fi rst remove it to gain access to the drive bays. To remove the bezel, fi rst unlock the front of the chassis then press the release knob (see Figure 6-3).

  • Page 81: Accessing The Drive Bays

    Chapter 6: Advanced Chassis Setup Figure 6-3. Removing the Front Bezel 1. Unlock 2. Press release knob 3. Remove bezel assembly Accessing the Drive Bays Hard Drives: Because of their hotswap capability, you do not need to access the inside of the chassis or power down the system to install or replace SATA drives. Proceed to the next section for instructions.

  • Page 82: Hard Drive Installation

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Hard Drive Installation The hard drives are mounted in drive carriers to simplify their installation and removal from the chassis. These carriers also help promote proper airfl ow for the drive bays. For this reason, even empty carriers without drives installed must remain in the chassis.
  • Page 83 Chapter 6: Advanced Chassis Setup Installing/Removing a Hard Drive 1. To remove a carrier, push the release button located beside the drive LEDs. 2. Swing the colored handle fully out and use it to pull the unit straight out (see Figure 6-5).

  • Page 84: Dvd-Rom Drive Installation

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual DVD-ROM Drive Installation The top cover of the chassis must be opened to gain full access to the DVD-ROM drive bay. The 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF accomodates only slim-line DVD-ROM drives. Side mounting brackets are needed to mount a slim-line DVD-ROM drive in the 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF server.

  • Page 85: Power Supply

    Chapter 6: Advanced Chassis Setup Power Supply 6016T-URF/6016T-NTRF The SuperServer 6016T-URF/6016T-NTRF has a 650 watt redundant power supply confi guration consisting of two hot-swap power modules. The power supply modules have an auto-switching capability, which enables them to automatically sense and operate with a 100V - 240V input voltage.

  • Page 86: 6016T-Uf/6016T-Ntf

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual 6016T-UF/6016T-NTF The SuperServer 6016T-UF/6016T-NTF has a single 560 watt power supply, which is auto-switching capable. This enables it to automatically sense and operate with a 100v - 240v input voltage. Power Supply Failure If the power supply module fails, the system will shut down and you will need to replace the module.
  • Page 87 Chapter 6: Advanced Chassis Setup Figure 6-6. Removing/Replacing the Power Supply 6-11...
  • Page 88 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Notes 6-12...

  • Page 89: Chapter 7 Bios

    Chapter 7: BIOS Chapter 7 BIOS Introduction This chapter describes the AMI BIOS Setup Utility for the X8DTU/X8DTU-F. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens. Starting BIOS Setup Utility To enter the AMI BIOS Setup Utility screens, press the <Delete>...

  • Page 90: Main Setup

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Starting the Setup Utility Normally, the only visible Power-On Self-Test (POST) routine is the memory test. As the memory is being tested, press the <Delete> key to enter the main menu of the AMI BIOS Setup Utility. From the main menu, you can access the other setup screens.
  • Page 91 Chapter 7: BIOS AMI BIOS • Version: This item displays the BIOS revision used in your system. • Build Date: This item displays the date when this BIOS was complete. Processor The AMI BIOS will automatically display the status of the processor used in your system: •...

  • Page 92: Advanced Setup Confi Gurations

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Advanced Setup Confi gurations Use the arrow keys to select Boot Setup and hit <Enter> to access the submenu items: BOOT Features Quick Boot If Enabled, this option will skip certain tests during POST to reduce the time needed for system boot.

  • Page 93: Processor And Clock Options

    Chapter 7: BIOS Wait For 'F1' If Error This forces the system to wait until the 'F1' key is pressed if an error occurs. The options are Disabled and Enabled. Hit 'Del' Message Display This feature displays "Press DEL to run Setup" during POST. The options are Enabled and Disabled.
  • Page 94 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Hardware Prefetcher (Available when supported by the CPU) If set to Enabled, the hardware pre fetcher will pre fetch streams of data and instruc- tions from the main memory to the L2 cache in the forward or backward manner to improve CPU performance.

  • Page 95: Advanced Chipset Control

    Chapter 7: BIOS C1E Support Select Enabled to use the feature of Enhanced Halt State. C1E signifi cantly reduces the CPU's power consumption by reducing the CPU's clock cycle and voltage during a "Halt State." The options are Disabled and Enabled. Intel®...
  • Page 96 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual QPI Links Speed This feature selects QPI's data transfer speed. The options are Slow-mode, and Full Speed. QPI Frequency This selects the desired QPI frequency. The options are Auto, 4.800 GT, 5.866GT, 6.400 GT. QPI L0s and L1 This enables the QPI power state to low power.
  • Page 97 Chapter 7: BIOS Hysteresis Temperature (This feature is available when Closed Loop is enabled.) Temperature Hysteresis is the temperature lag (in degrees Celsius) after the set DIMM temperature threshold is reached before Closed Loop Throttling begins. The options are Disabled, 1.5 o C, 3.0 C, and 6.0 Guardband Temperature (This feature is available when Closed Loop is enabled.)
  • Page 98 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual providing the user with greater reliability, security and availability in networking and data-sharing. The options are Enabled and Disabled. SR-IOV Supported Select Enabled to enable Single Root I/O Virtualization (SR-IOV) support which works in conjunction with the Intel Virtualization Technology and allow multiple op- erating systems running simultaneously within a single computer via natively share PCI-Express devices in order to enhance network connectivity and performance.
  • Page 99 Chapter 7: BIOS USB Functions This feature allows the user to decide the number of onboard USB ports to be en- abled. The Options are: Disabled, 2 USB ports, 4 USB ports, 6 USB ports, 8 Ports, 10 Ports and 12 USB ports. USB 2.0 Controller This item indicates if the onboard USB 2.0 controller is activated.
  • Page 100 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual SATA AHCI (Available when the option-AHCI is selected.) Select Enable to enable the function of Serial ATA Advanced Host Interface. (Take caution when using this function. This feature is for advanced program- mers only.) IDE Detect Timeout (sec) Use this feature to set the time-out value for the BIOS to detect the ATA, ATAPI devices installed in the system.
  • Page 101 Chapter 7: BIOS PCI-E Slot from SXB1/PCI-E Slot from SXB2/PCI-E Slot from SXB3 Select Enabled to enable PCI-E SXB1 slot, PCI-E SXB2 slot or PCI-E SXB3 slot. It can also enable Option ROMs to boot computer using a network interface from these slots.

  • Page 102: Hardware Health Monitor

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Serial Port Mode This feature allows the user to set the serial port mode for Console Redirection. The options are 115200 8, n 1; 57600 8, n, 1; 38400 8, n, 1; 19200 8, n, 1; and 9600 8, n, 1.
  • Page 103 Chapter 7: BIOS The options are: • The Early Alarm: Select this setting if you want the CPU overheat alarm (includ- ing the LED and the buzzer) to be triggered as soon as the CPU temperature reaches the CPU overheat threshold as predefi ned by the CPU manufacturer. •...
  • Page 104 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual User intervention: No action is required. However, consider checking the CPU fans and the chassis ventilation for blockage. High – The processor is running hot. This is a ‘caution’ level since the CPU’s ‘Tem- perature Tolerance’ has been reached (or has been exceeded) and may activate an overheat alarm.
  • Page 105 Chapter 7: BIOS High Performance Event Timer Select Enabled to activate the High Performance Event Timer (HPET) that produces periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in synchronizing multimedia streams, providing smooth playback and reducing the de- pendency on other timestamp calculation devices, such as an x86 RDTSC Instruc- tion embedded in the CPU.
  • Page 106 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Status of BMC Working The Baseboard Management Controller (BMC) manages the interface between system management software and platform hardware. This item displays the status of the current BMC controller.  View BMC System Event Log This feature displays the BMC System Event Log (SEL).
  • Page 107 Chapter 7: BIOS  Set LAN Confi guration Set this feature to confi gure the IPMI LAN adapter with a network address as shown in the following graphics. Channel Number - Enter the channel number for the SET LAN Confi g com- mand.
  • Page 108 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual  SET PEF Confi guration PEF Support Select Enabled to enable the function of Platform Event Filter (PEF) which will interpret BMC events and perform actions based on pre-determined settings or 'traps' under IPMI 1.5 specifi cations. Powering the system down or sending an alert when a triggering event is detected.

  • Page 109: Security Settings

    Chapter 7: BIOS BMC Watch Dog TimeOut [Min:Sec] This option appears if BMC Watch Dog Timer Action (above) is enabled. This is a timed delay in minutes or seconds, before a system power down or reset after an operating system failure is detected. The options are [5 Min], [1 Min], [30 Sec], and [10 Sec].
  • Page 110 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Supervisor Password This item indicates if a Supervisor password has been entered for the system. "Not Installed" means a Supervisor password has not been used. User Password This item indicates if a user password has been entered for the system. "Not In- stalled"...

  • Page 111: Boot Confi Guration

    Chapter 7: BIOS Boot Confi guration Use this feature to confi gure boot settings. Boot Device Priority This feature allows the user to specify the sequence of priority for the Boot Device. The settings are 1st boot device, 2nd boot device, 3rd boot device, 4th boot device, 5th boot device and Disabled.

  • Page 112: Exit Options

    UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Exit Options Select the Exit tab from the AMI BIOS Setup Utility screen to enter the Exit BIOS Setup screen. Save Changes and Exit When you have completed the system confi guration changes, select this option to leave the BIOS Setup Utility and reboot the computer, so the new system con- fi...

  • Page 113: Appendix A Bios Error Beep Codes

    Appendix A: BIOS Error Beep Codes Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
  • Page 114 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Notes...

  • Page 115: Appendix B Installing Windows

    Appendix B: Installing Windows Appendix B Installing Windows After all hardware components have been installed, you must fi rst confi gure Intel South Bridge RAID Settings before you install the Windows OS and other software drivers. To confi gure RAID settings, please refer to RAID Confi guration User Guides posted on our web site at www.supermicro.com/support/manuals.
  • Page 116 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual B-2 Installing the Windows OS for a Non-RAID System 1. Insert Microsoft's Windows Setup CD in the CD drive, and the system will start booting up from the CD. 2. Continue with the OS installation. The Windows OS Setup screen will display. 3.

  • Page 117: Appendix C System Specifi Cations

    Appendix C: System Specifi cations Appendix C System Specifi cations Processors Single or dual Intel® 5500 Series processors in LGA1366 sockets Note: Please refer to our web site for a complete listing of supported processors. Chipset Intel IOH-36D/ICH10R chipset BIOS 32 Mb AMI®...
  • Page 118 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual Expansion Slots 6016T-URF/6016T-UF: Right side: (optional) 2x Gb LAN ports w/ RSC-R1UU-E8PR riser card and AOC-PG-i2+ add-on card Left side: one UIO card and one PCI Express x16 slot 6016T-NTRF/6016T-NTF: Right side: (optional) 2x Gb LAN ports w/ RSC-R1UU-E8PR riser card and AOC-PG-i2+ add-on card Left side: two PCI Express x8 slots Serverboard...
  • Page 119 Appendix C: System Specifi cations Operating Environment Operating Temperature: 10º to 35º C (50º to 95º F) Non-operating Temperature: -40º to 70º C (-40º to 158º F) Operating Relative Humidity: 8% to 90% (non-condensing) Non-operating Relative Humidity: 5 to 95% (non-condensing) Regulatory Compliance Electromagnetic Emissions: FCC Class A, EN 55022 Class A, EN 61000-3-2/- 3-3, CISPR 22 Class A...
  • Page 120 UPER ERVER 6016T-URF/6016T-UF/6016T-NTRF/6016T-NTF User's Manual (continued from front) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency com- munication devices or other critical systems whose failure to perform be reasonably expected to result in signifi...

This manual is also suitable for:

Superserver 6016t-ufSuperserver 6016t-ntfSuperserver 6016t-ntrf

Table of Contents