Download Print this page

Standard Features And Options - Generac Power Systems SD275 Instruction Manual

275 kw industrial diesel generator set

Advertisement

SD275
GENERATOR SET
˜ Genset Vibration Isolation
™ IBC Seismic Certified/Seismic Rated Vibration Isolators
™ Extended warranty
™ Gen-Link Communications Software
4 of 5
™ Steel Enclosure
™ Aluminum Enclosure
ENGINE SYSTEM
General
˜ Oil Drain Extension
™ Oil Make-Up System
™ Oil Heater
˜ Air cleaner
˜ Fan guard
˜ Radiator duct adapter
Fuel System
˜ Fuel lockoff solenoid
˜ Secondary fuel filter
˜ Stainless steel flexible exhaust connection
˜ Industrial Exhaust Silencer
™ Critical Exhaust Silencer
™ Flexible fuel lines
™ Primary fuel filter
™ Single Wall Tank (Export Only)
™ UL 142 Fuel Tank
Cooling System
™ 120VAC Coolant Heater
™ 208VAC Coolant Heater
˜ 240VAC Coolant Heater
™ Other Coolant Heater_______________________
˜ Closed Coolant Recovery System
˜ UV/Ozone resistant hoses
˜ Factory-Installed Radiator
˜ Radiator Drain Extension
Engine Electrical System
˜ Battery charging alternator
˜ Battery cables
˜ Battery tray
™ Battery box
™ Battery heater
˜ Solenoid activated starter motor
™ 10A UL float/equalize battery charger
˜ Rubber-booted engine electrical connections
ALTERNATOR SYSTEM
˜ UL2200 GENprotect™
™ Main Line Circuit Breaker
™ 2nd Circuit Breaker
™ 3rd Circuit Breaker
™ Alternator Upsizing
™ Anti-Condensation Heater
™ Tropical coating
˜ Permanent Magnet Generator

standard features and options

CONTROL SYSTEM
Control Panel
Std
˜ Digital H Control Panel - Dual 4x20 Display
Opt
™ Digital G-100 Control Panel - Touchscreen
Opt
™ Digital G-200 Paralleling Control Panel - Touchscreen
Opt
˜ Programmable Crank Limiter
Opt
™ 21-Light Remote Annunciator
Opt
™ Remote Relay Panel (8 or 16)
˜ 7-Day Programmable Exerciser
˜ Special Applications Programmable PLC
˜ RS-232
Std
˜ RS-485
Opt
˜ All-Phase Sensing DVR
Opt
˜ Full System Status
Std
˜ Utility Monitoring (Req. H-Transfer Switch)
Std
˜ 2-Wire Start Compatible
Std
˜ Power Output (kW)
˜ Power Factor
˜ Reactive Power
Std
˜ All phase AC Voltage
˜ All phase Currents
Std
˜ Oil Pressure
Std
˜ Coolant Temperature
Std
˜ Coolant Level
Opt
™ Oil Temperature
Opt
˜ Fuel Pressure
Opt
˜ Engine Speed
-
˜ Battery Voltage
Opt
˜ Frequency
˜ Date/Time Fault History (Event Log)
Opt
™ Low-Speed Exercise
Opt
˜ Isochronous Governor Control
Std
˜ -40deg C - 70deg C Operation
-
˜ Waterproof Plug-In Connectors
Std
˜ Audible Alarms and Shutdowns
Std
˜ Not in Auto (Flashing Light)
Std
˜ Auto/Off/Manual Switch
Std
˜ E-Stop (Red Mushroom-Type)
™ Remote E-Stop (Break Glass-Type, Surface Mount)
Std
™ Remote E-Stop (Red Mushroom-Type, Surface Mount)
Std
™ Remote E-Stop (Red Mushroom-Type, Flush Mount)
Std
˜ NFPA 110 Level I and II (Programmable)
Opt
˜ Remote Communication - RS232
Opt
™ Remote Communication - Modem
Std
™ Remote Communication - Ethernet
Opt
™ 10A Run Relay
Std
Alarms (Programmable Tolerances, Pre-Alarms and Shutdowns)
™ Low Fuel
˜ Oil Pressure (Pre-programmed Low Pressure Shutdown)
˜ Coolant Temperature (Pre-programmed High Temp Shutdown)
Std
˜ Coolant Level (Pre-programmed Low Level Shutdown)
Opt
˜ Oil Temperature
Opt
˜ Engine Speed (Pre-programmed Overspeed Shutdown)
-
˜ Voltage (Pre-programmed Overvoltage Shutdown)
Opt
˜ Battery Voltage
Opt
Opt
Other Options
Std
Std
na
na
Std
Opt
Opt
Std
Std
Std
Std
Std
Std
Std
Std
Std
Std
Std
Std
Std
Std
Std
Std
Opt
Std
Std
Std
Std
Std
-
Std
Std
Std
Std
Std
Std
Std
Opt
Opt
Opt
Std
Std
Opt
Opt
Opt
Opt
Std
Std
Std
Std
Std
Std
Std

Advertisement

loading

This manual is also suitable for:

Sd200Sd300Sd250