Advertisement
Quick Links
PX-D1
The Electro-Voice® PX-D1 accessory consists of a pair of dolly plates with assembled casters for use with the Phoenix
PX2122 and PX2152 Loudspeakers. Each dolly plate is capable of rotating out of the way when the dolly is not in use. This
is especially useful for when the speakers are being shipped or arrayed, whether on a groundstack or hanging from a grid.
1. Remove (2) 5/16" bolts from rear of the PX2122 or PX2152 enclosure.
2. Align the plastic standoffs with the recesses in the enclosure so the dolly board is perpendicular to the length of
the enclosure. Turn the wing screw into the enclosure until tight (see Figure 1).
3. When not being used for transport, rotate the dolly boards so they are parallel to the length of the enclosure.
Loosen the wing screw until the dolly board is able to rotate freely. Turn the dolly board 90°, and tighten the wing
screw (see Figure 2).
CAUTION! If the dolly boards are removed, replace the (2) 5/16" bolts into the rear of the
enclosure. If the bolts are not replaced, the speaker will have air leaks resulting in undesirable
performance.
Remove Existing
Screws, Install
Dolly Plates, then
Attach Wing
Screws (2 Places)
Figure 1: Assembling the PX-D1 to a Phoenix
PX2122 or PX2152 Loudspeaker
Loosen Wing
Screws, Rotate and
Align Grooves, then
Re-attach Wing
Screws
Figure 2: Rotating the PX-D1 on the rear of a
Phoenix Loudspeaker for shipping or arraying
Phoenix Series
Accessories
User Instructions
Advertisement
Summary of Contents for Electro-Voice PX-D1
- Page 1 PX-D1 The Electro-Voice® PX-D1 accessory consists of a pair of dolly plates with assembled casters for use with the Phoenix PX2122 and PX2152 Loudspeakers. Each dolly plate is capable of rotating out of the way when the dolly is not in use. This is especially useful for when the speakers are being shipped or arrayed, whether on a groundstack or hanging from a grid.
- Page 2 PX-D2 The Electro-Voice® PX-D2 accessory consists of a pair of dolly plates with assembled casters for use with the Phoenix PX2181 Loudspeaker. The dolly plates double as skid plates for extra protection of the PX2181’s back panel. 1. Remove (16) 5/16” bolts from rear of the PX2181 enclosure.
- Page 3 PX-G1 The Electro-Voice® PX-G1 is an array kit that allows for suspension of up to (3) PX2122’s or (2) PX2152’s on a material lift. There are multiple horizontal splay and vertical tilt options that make the PX-G1 useful in many applications.
- Page 4 Note final orientation of eyebolts. For permanent installations, use a thread locker (not included) on the button head screws and eyebolts (See Figures 5 and 6). WARNING! Electro-Voice strongly recommends that M10 forged shoulder eyebolts that are compliant with DIN580 standards are used as redundant safety points for the array (See Figure 5 for recommended locations).
- Page 5 Installation of the PX-G1 (continued) 4. Install the material lift adaptors to the material lift by Long Pin sliding the tube over the fork, and installing the long Material Lift Forks pin through the hole in the fork (See Figure 9). WARNING! Make sure the pins for each material lift adaptor Material Lift Adaptors...
- Page 6 Installation of the PX-G1 (continued) 6. Following safe rigging practices, attach rated safety cabling (not included) from the material lift to the eyebolts (See Figure 12). WARNING! The center of gravity of the array is located below the hole on the material lift forks.