Advertisement
Installation of the PX-G1 (continued)
4. Install the material lift adaptors to the material lift by
sliding the tube over the fork, and installing the long
pin through the hole in the fork (See Figure 9).
WARNING! Make sure the pins
for each material lift adaptor
pass through their respective
holes in material lift forks, and
fully lock or engage other side of material lift adaptors.
Do not lift any array without ensuring pins pass through
forks and are fully locked or engaged.
5. Attach the material lift adaptors to the array bracket
using the short pins (See Figure 10). There are 17
holes on the array bracket (A-Q) that can be used
to approximate the desired vertical tilt angle. See
the table below to determine which holes should be
used to achieve the desired tilt angle.
WARNING! Make sure the pins
for each material lift adaptor
pass through their respective
holes in array bracket, and fully
lock or engage other side of material lift adaptors. Do
not lift any array without ensuring pins pass through
bracket and are fully locked or engaged.
P
- X
G
M
o
d
l e
C
o
f n
g i
- 1
r A
a r
y
- 2
r A
a r
H
o
i r
° z
N
A /
3
° 0
H
o
e l
#
A
+
6
+
8
B
+
4
+
6
C
+
1
5 .
+
4
D
0 -
5 .
+
2
E
2 -
5 .
0
F
5 -
2 -
5 .
G
7 -
4 -
H
9 -
6 -
I
-
1 1
8 -
5 .
J
1 -
3
1 -
0
5 .
K
1 -
5
5 .
1 -
2
5 .
L
1 -
7
5 .
1 -
5
M
1 -
9
1 -
7
N
2 -
1
1 -
9
O
2 -
3
2 -
1
P
2 -
5
2 -
2
5 .
Q
2 -
6
5 .
2 -
4
5 .
Note: All angles shown in chart are approximate. Cabling
and any other supplementary equipment may change the
absolute angle of the entire array from what is shown in the
chart. Do not attempt to tilt an array beyond the angles
shown in the chart.
1
V
e
t r
c i
l a
T
t l i
A
n
g
e l
s
P
X
2
1
2
2
y
- 3
r A
a r
y
- 1
4
° 5
3
° 0
4
° 5
+
1
2
+
1
0
+
1
2
+
1
0
+
8
+
1
0
+
8
+
6
+
8
+
6
+
3
+
6
+
4
+
1
5 .
+
4
+
2
0
+
2
0
3 -
0
2 -
5 -
2 -
4 -
5 .
7 -
4 -
5 .
6 -
5 .
9 -
6 -
5 .
9 -
-
1 1
8 -
5 .
-
1 1
1 -
3
5 .
-
1 1
1 -
3
1 -
5
5 .
1 -
3
1 -
5
1 -
7
5 .
1 -
5
1 -
7
1 -
9
5 .
1 -
7
1 -
9
2 -
1
5 .
1 -
9
2 -
1
2 -
3
5 .
2 -
1
Figure 9: Assembling the Material Lift Adaptors
Short Pin
P
X
2
1
5
2
r A
a r
y
- 2
r A
a r
y
N
A /
4
° 5
Figure 10: Assembling the Array Bracket to the
+
7
+
1 1
5 .
+
5
+
9
5 .
+
2
5 .
+
7
5 .
+
0
5 .
+
5
1 -
5 .
+
3
3 -
5 .
+
1
6 -
1 -
5 .
8 -
3 -
5 .
1 -
0
5 -
5 .
1 -
2
7 -
5 .
1 -
4
1 -
0
1 -
6
-
1 1
5 .
1 -
8
1 -
3
5 .
2 -
0
1 -
5
5 .
2 -
2
1 -
7
5 .
2 -
4
1 -
9
5 .
2 -
5
5 .
2 -
1
5 .
Figure 11: Vertical Tilt Angle Configurations
Long Pin
Material Lift Forks
Material Lift Adaptors
to Material Lift Forks
Material Lift Forks
and Adaptors
Array
Bracket
Material Lift Adaptors
Long Pin
Short Pin
Advertisement
