AEG B 99852G User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

B 99852G

Hob

User Manual

Table of Contents

Summary of Contents for AEG B 99852G

Page 1 B 99852G User Manual...
Page 2: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations.
Page 3 Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance.
Page 4: Table Of Contents
Contents Instructions for the User Important Safety Information Description of the Hob Operation Maintenance and Cleaning Something Not Working? Service and Spare Parts Customer Care Guarantee Conditions European Guarantee Instructions for the Installer Important safety requirements Installation Building In Electrical connections Wiring diagram Fault Finding Commissioning...
Page 5: Description Of The Hob
Description of the Hob Hob Top Semi-rapid Burners Auxiliary Burner Ultra-rapid Burner (triple crown) Control knobs INSTALLATION Any gas installation must be carried out by a competent person, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown.
Page 6: Operation
Operation Hob burners To light a burner: Push in the relevant control knob and turn it to maximum position. Upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (fig. 1 - letter D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted.
Page 7 To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Burner minimum maximum diameter diameter Large (ultra-rapid) 180 mm 260 mm Medium (semi-rapid) 120 mm 220 mm Small (Auxiliary) 80 mm...
Page 8: Maintenance And Cleaning
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water...
Page 9: The Burners
Pan Supports To keep the pan supports in the correct position, they are mounted on metal pins located in the back of the hob. After cleaning the hob, ensure the pan supports are properly placed as shown in fig. 3. The pan supports are dishwasher proof.
Page 10: Something Not Working
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown...
Page 11: Service And Spare Parts
Instructions for the Installer Instructions for the Installer Engineers technical data Overall dimensions Burner Dia. Tap By-pass 1/100 mm Width: 880 mm Depth: 510 mm Auxiliary Semi-rapid Cut out dimensions Ultra-rapid Width: 830 mm Depth: 480 mm Aeration adjustment none Supply Connections Semi-rapid Burner 1.9 kW (6,483 BTU/HR) Gas: RC 1/2 inch (1/2 inch male) Rear right...
Page 12: Important Safety Requirements
Instructions for the Installer Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations.
Page 13: Installation
Instructions for the Installer Installation Important This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored.
Page 14: Building In
Instructions for the Installer Cut Out Size The dimensions of the cut-out are given in the diagram. FO 2349 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
Page 15: Building Over A Kitchen Unit With Door
Instructions for the Installer ON/OFF SWITCH ON/OFF SWITCH FLEX OUTLET FLEX OUTLET FO 0764 FO 0763 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated.
Page 16: Fitting The Hob To The Worktop
Instructions for the Installer Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below.
Page 17: Electrical Connections
Instructions for the Installer Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply.
Page 18: Wiring Diagram
Instructions for the Installer Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations.
Page 19: Fault Finding
Instructions for the Installer Fault Finding Blue Brown Green Yellow Preliminary Electrical Systems Check START Blue Isolate appliance and carry out: Green Brown Yellow A: Earth Continuity check. Carry out: Carry out: D: Resistance to C: Polarity check. Earth check. Has inlet fuse blown? Electricity supply should now be...
Page 20 Instructions for the Installer A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω...
Page 21 Instructions for the Installer Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse and Light burner manually replace if necessary Check by pass simmer Check polarity and earth adjusted continuity of supply point Check fitting of Check position of the Check earth continuity...
Page 22: Commissioning
Instructions for the Installer Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
Page 23: Conversion From Natural Gas To Lpg
Instructions for the Installer Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit.
Page 24: Customer Care
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area.For the address of your local Service Force Centre and further informa- tion about Service Force, please visit the website at www.serviceforce.co.uk...
Page 25: Guarantee Conditions
Guarantee Conditions Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG- Electrolux appliance or any part thereof is pro-ved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: •...
Page 26: European Guarantee
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed be-low the appliance guarantee will move with you subject to the following qualificati-ons: The appliance guarantee starts from the date you first purchased the appliance which •...

AEG B 99852G User Manual

Quick Links

Related Manuals for AEG B 99852G

Summary of Contents for AEG B 99852G

Table of Contents