Subscribe to Our Youtube Channel
Related Manuals for BEGLEC MOVING HEAD SPOT
Summary of Contents for BEGLEC MOVING HEAD SPOT
- Page 1 Professional Lighting Technology WWW. BEGLEC.COM User Guide Please read these instructions carefully before use...
-
Page 2: Table Of Contents
Note TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 2.1 Inserting/Exchanging rotating gobos 3. Lamp 4. How To Set The Unit 4.1 Control Panel 4.2 Main Function 5. How To Control The Unit 5.1 Master/Slave Built-In Preprogrammed Function. 5.2 Easy Controller 5.3 Universal DMX Controller 5.4 DMX512 Configuration 5.5 DMX512 Connection... -
Page 3: Safety Instruction
1. Safety Instruction 7. Fixture Cleaning Please read carefully the instruction, which includes important The cleaning of internal and external optical lenses and/or mirrors must be carried out information about the installation, usage and maintenance. periodically to optimize light output. Cleaning frequency depends on the environment in which WARNING the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. - Page 4 Warning G. If The pan belt is broken To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or 1. Turn off the main power. moisture. 2. Unscrew all the screws (A) and open the base-housing cover (B). Never touch bulb with bare fingers, as it is very hot after using.
-
Page 5: Technical Specification
2. Technical Specification 6. Troubleshooting Power supply Following are a few common problems that may occur during operation. Here are some - AC 120V~60Hz or 230V/240V/250V 50/60Hz suggestions for easy troubleshooting: Lamp A. The unit does not work, no light and the fan does not work - Discharge lamp MSD 250W GY9.5 1. -
Page 6: Inserting/Exchanging Rotating Gobos
5.5. DMX512 Connection Luminous intensity: The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. 2.1. Inserting/Exchanging rotating gobos DANGER! Install the gobos with the device switched off only. Unplug from mains before changing gobos! Open the cover by loosening the fastening screw at the sides of the cover. -
Page 7: Lamp
3. Lamp In case of replacement of the lamp or maintenance, do not open the fixture within 15 minutes until the unit cools down after switching off. Because of its high internal pressure, there might be a risk that the Discharge lamp would explode during operation. -
Page 8: How To Set The Unit
5.4. DMX512 Configuration 4. How To Set The Unit 4.1. Control Panel Display To show the various menus and the selected functions. DMX input present MASTER Master mode SLAVE Slave mode SOUND Flashing Sound activation Button MENU To select the programming functions DOWN To go backward in the selected functions To go forward in the selected functions... -
Page 9: Main Function
4.2. Main Function 5.2. Easy Controller To select any of the pre-set functions, press the MENU button up to when the required one is shown on the display. Select the function by ENTER button and the display will blink. Use The easy remote controller is used only in master/slave mode. -
Page 10: How To Control The Unit
5. How To Control The Unit Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to change the DMX512 address. You can operate the unit in three ways: Once the address has been selected, press the ENTER button to setup or automatically 1. - Page 11 Color Mode Focus Adjust Press the MENU button up to when the is shown on the display. Pressing ENTER Press the MENU button up to when the is blinking on the display. Pressing ENTER button, the unit will focus on tilt 90°, and then the unit will focus on pan 0°, pan 90°, pan180°, button and the display will blink.
Need help?
Do you have a question about the MOVING HEAD SPOT and is the answer not in the manual?
Questions and answers